Coding List Golf 8

BCM control unit 9 - Adaptation - Licht Konfig-Abhanging - Allwatterlicht - Not instaled

Similar to phonostar for European models, is there a way for US vehicles to update Radio Station Data? My part number is 5H0035871

After enabling acceleration measurement (1.1.46) I am getting a dynamic cornering light error. I know it says a basic adjustment to headlight is required, but what does that mean? 

*fixed - there is an adaptation call "acknowledge basic settings" that made it go away. 

Yes it did! I didn't get the chance to get a real 0-60 time, but once I hit start, came to a complete stop it showed that it was ready. As soon as I hit the gas the timer started. For reference I have a 2023 R (but not sure about firmware versions) 

And here is my biweekly disclaimer:
Coding 4B will reset all adaptive light settings:
*Automatic leveling
*Matrix

While automatic leveling could be reset (although in a wrong/unchecked basic level), Matrix will need actual measurements from a tuning device. You can read them from basic settings and re-enter or have them recalibrated at a workshop.
Entering bogus values (or all zero) will not correctly enable matrix.

It makes the difference that you either do it according to the specs and have a decent result or you just fake the correct procedure and are lucky or not.

How this works in a workshop:
Auto levelling
*Start leveling basic setting. Leveling is reset to a zero position.
*Level/Adjust headlights with lightbox and screwdriver.
*Aknowledge basic setting
=>The car now has a well levelled setting. When the sensor(s) are indicating that the car is loaded or unloaded, the headlight will adjust.
There is no "feedback loop" with the camera or something. When it is off, it is off.
Pitfalls: When this is done on a non-leveled surface, the lights are still following the car's load, but will always be too high or too low.

You can read the load sensors actual values and basic setting in live data. You could reload the car to match the saved basic setting for this. I expierienced a bug in OBD11 not correctly showing the values, so take care here. There is no way of manually entering these values.

Matrix basic setting:
*Start basic setting. "Reference segments" are lit up.
*With a matrix capable testing device the vertical offset of these segments is measured
*Feed back the positions to the car's tester. No tools needed.

Pitfalls: Everything. There is no way of doing this at home with a best effort strategy.

You can read the offsets from the live data and just write them back in the procedure. Of course, you will need to do this (and write them down) before changing the coding.
Make sure the values are correctly saved, as the live data shows 3 representation, but only one is valid for entering.

hi , this your LINK not work .... have a new link for this PDF codes ? thanks

n3oka

The problem i have now is, it detects empty lane and shows little arrow, but as soon as i indicate it switches off lane assist (as normally it would do without active lane change assist) for a brief time so i can manually change lane. It acts like it sees lane but is unable to turn the wheel by itself. Could be:

So i followed every step to try to code Active Lane Change Assistant. 
Control unit 44 and A5 exactly the same. But in 09 in adaptations i don't have BCM as shown in screenshot. I tried Travel (as travel assist), BCM, body, Fahrerassistenz, Blinkfunktionen, Blinken. There is no such a thing in my 09 control unit. I have (09 control module) HV 5WA937086E, SV 0158. In OBD11 app it shows there a new version for my control unit but i don't know how to update it by myself, tip would help i'm willing to learn and test new thing.

Also even tho i have travel assist, and everything is working fine. In driver assist setting i didn't have Travel Assist as i have now after this coding. But if i tap on it i have this error (screenshot).  Why do you thing i didn't had that menu in setting and why it shows error? Any suggestions? 

newty Thank you. When i switched to German database there it is. Will try and report how well or bad it runs

Hold the steering wheel gently. If it detects that you are not holding the steering wheel, lane change assistant becomes passive. If everything is OK, when it gives the signal, it will make a smooth transition in that direction. good luck

So you have the oldest AID display with software 1400. If you enabled the View 9 and it doesn't show up then it means that it is missing in the software itself.

Hello n3oka, I have been trying to retrofit my rain/light sensor for a while now.
Unfortunately, the setting where I can activate the rain sensor does not appear in the menu.
Could you help me?
I think these are the relevant variables.

LWRKonfiguration:
rain_light:
nicht freigeschaltet
HMI_Wiper_Comfort_Rain_Sensor_OFF:
Active
Regensensorik_Verbauund_ABT_Steuerung:
Regensensor:
nicht verbaut
Front_wiper:
Regensensor aktivieren:
Aktiv
Regensensor aktiv Fahrfreigabe:
nicht aktiv
Identifikation der Subbusteilnehmer:
Sensor für Regen- und Lichterkennung:
Alt
Assistenzlichtfunktionen:
Assistenzfahrlicht bei Regen:
nicht aktiv
Maskierung_Regenlichtmenü:
aktiv

Hi, 

yes i can add that at my excel file.
ill add an translation button soon too.

gentleman
I dont know exactly but check:

09
Regensensorik_Verbau und_ABT_Steuerung

Regensensor             LIN_Regen_Licht_Sensor

Lichtsensor               LIN_Regen_Licht_Sensor
HMI_Wiper_Comfort_Rain_Sensor_OFF    active

4B

coding:
rain_light_sensor: installed