|
Post by andrea on Jan 30, 2021 21:47:43 GMT
I'm trying to install the OEM rear camera, code 8V0827566B. My car is A3 facelift 2019. Could you please help me with the OBDeleven coding? Thanks!
|
|
|
Post by dv52 (Australia) on Jan 31, 2021 21:05:10 GMT
andrea : It's a bit Chinese-ey, but the instruction here might help. Don
|
|
|
Post by andrea on Feb 1, 2021 13:41:56 GMT
This is a summary of what I find (maybe usefull for other users of the forum...):
Coding (OBD eleven):1. Register the module in the 19-gateway (6C or "Camera System Rear View") -> coded
2. Module 76 (or module 10, depends on the car) Parking Assistance - Long code helper - (active rear camera -> installed)
or byte 02, bit 4 -> set to "1" (depends on the car)
3. Module 6C code: (02 73 01 01 22 00 20 01 40 00 40)
4. Finally you have to enter the Module 5F Adaptation Car_Funktion_List_BAP_Gen2_VPS_0x0B Switch to activated Car_Funktion_List_BAP_Gen2_VPS_0x0B_msg_bus dial terminal 15 Wiring:The camera has 6 wires (2 for FBAS, 2 for CAN, 2 for power supply) FBAS (video signal) * Connect the signal cables to the Quadlock (Blue Connector) White Wire from Camera into Blue connector in MMI #6 Black Wire from Camera into Blue connector in MMI #12 (shielding) CAN - twisted pairs * the orange/purple -> gateway pin 10 (Infotainment CAN-low J533 T20A) * the black -> gateway pin 20 (Infotainment CAN-high J533 T20A). or you can connect CAN directly on MMI connector "E" (white/gray housing) 6 - CAN-bus High (Infotainment) 12 - CAN-bus Low (Infotainment) Power supply 7.5A fused power supply (fuse box under the steer - F18 Rear camera) Earth Connection
|
|
|
Post by dv52 (Australia) on Feb 1, 2021 19:39:04 GMT
andrea : In the steps in my link, " if you have installed parking assistance system please code "10" tick rear camera installed" refers to the instructions using VCDS In OBD11 speak, it means go to the Parking Assistance module @ address hex76 - select Coding - navigate to Byte 2 and tick Bit 4Don
|
|
mad74
New Member
Posts: 3
|
Post by mad74 on Feb 3, 2021 19:43:16 GMT
Hi,
Have anybody a picture how to install it?
Regards M.
|
|
|
Post by dv52 (Australia) on Feb 4, 2021 0:31:02 GMT
|
|
mad74
New Member
Posts: 3
|
Post by mad74 on Feb 4, 2021 12:35:58 GMT
Thanks, but ment how to install the hardware, but thanks for the pictures where to find!
|
|
mad74
New Member
Posts: 3
|
Post by mad74 on Oct 25, 2021 17:58:16 GMT
Hi,
I've installed my oem backup Camera and nou I will doe the coding with my obdeleven. The instructions above are changed in the obdeleven menu?? Have someone the new menu layout for me how to code please?
|
|
nickalto
New Member
obd11 activation rear view camera low line Skoda Karoq NU7 help needed
Posts: 8
|
Post by nickalto on Oct 2, 2023 19:12:08 GMT
Hello do you have any instructions for coding with obd11 a retrofited rear camera low line for a skoda karoq 2018 model ?i have also retrofit and rear parking aid with OPC which also needs coding! thanks
|
|
|
Post by dv52 (Australia) on Oct 2, 2023 23:56:32 GMT
|
|
nickalto
New Member
obd11 activation rear view camera low line Skoda Karoq NU7 help needed
Posts: 8
|
Post by nickalto on Oct 5, 2023 18:05:06 GMT
Thank you for your answer Do you have also the coding for rear parking pilot with ops?
|
|
|
Post by dv52 (Australia) on Oct 5, 2023 20:15:02 GMT
|
|
nickalto
New Member
obd11 activation rear view camera low line Skoda Karoq NU7 help needed
Posts: 8
|
Post by nickalto on Oct 7, 2023 6:06:16 GMT
Thank you again. Everything works fine with rear view camera but the park pilot doesn't. The problem is that when I try to activate byte3 bit4 in 76 Parking Assistance I get always the message "not supported".And also when I put in reverse I get a notification in dash panel "Park Pilot malfunction ".I double checked wiring and looks fine.Could this be a problem of compatibility?any suggestions or ideas?
|
|
|
Post by dv52 (Australia) on Oct 7, 2023 20:22:46 GMT
nickalto : hmm........ it's difficult to make comment given that I know absolutely zero about this retrofit project.
Some random thoughts that come to mind (these are wild guesses): - Do you have the correct module for the number of sensors?
- If your module is 5Q0919298 - you should have 12 x sensors (6 x sensors on front and rear)
- If your module is 5Q0919294 - you should have 8 x sensors (4 x sensors on front and rear)
- Double check your wiring:
- Check that pin #1 on each sensor is connected together (this will be the +12V supply when connected to pin #14 on the module)
- Check that pin #3 on each sensor is connected to car earth
- Try entering the security code 20104 BEFORE making the long code change
- Does the SCAN on this car report errors in the hex76 module?
Don
|
|
nickalto
New Member
obd11 activation rear view camera low line Skoda Karoq NU7 help needed
Posts: 8
|
Post by nickalto on Oct 8, 2023 11:41:08 GMT
Thank you again for your valuable help.After searching everything I noticed a small detail: for some reason that I don't understand when I run the long coding I saw that the gearbox of my car was coded to automatic!!!I changed it to manual gearbox and everything now seems working fine!!!It is strange but I suppose that after changing it the CANBUS module can read the 2 new CAN connections I made with the aid parking module J446!!! Here I must notice that with obd11 I had an easy task cause everything is easy to find and understand in long coding or adaptation. Anyway for now everything seems to work fine!I hope that it will continue! Thank you again!
|
|
|
Post by karim13012 on Oct 16, 2023 13:50:51 GMT
andrea : It's a bit Chinese-ey, but the instruction here might help. Don Hello bro Need coding on obdeleven rear camera for Audi a1 2019 please
|
|
|
Post by karim13012 on Oct 16, 2023 13:52:22 GMT
Hello need coding rear view camera for Audi a1 please on obdeleven
|
|
|
Post by dv52 (Australia) on Oct 16, 2023 21:22:04 GMT
karim13012: Hi. OK, you need coding advice - but I need information about this retrofit. What type of RVC- what type of MIB? Don
|
|
|
Post by johnwilliams1 on Oct 31, 2023 12:37:38 GMT
To install the OEM rear camera with code 8V0827566B on your A3 facelift 2019, you'll need to do some coding using OBDeleven. First, ensure that the hardware is properly installed. Then, use OBDeleven to enable the rear camera function in your car's settings.
|
|
|
Post by dv52 (Australia) on Oct 31, 2023 20:17:35 GMT
John: Wow - seldom have I seen such a seamless segue from general coding advice to a marketing advertisement. I wonder which of the two motivated the response? Of course the latter is spam, which is counter to the forum rules!
Don
|
|
nickalto
New Member
obd11 activation rear view camera low line Skoda Karoq NU7 help needed
Posts: 8
|
Post by nickalto on Nov 21, 2023 7:42:21 GMT
Hello again after a retrofit of original rear view camera and rear parking aid with opc in my skoda karoq thé only thing left in diagnostic fault is the U112100 fault :datenbus missing!everything works fine but I still get this message! Maybe I have a sensor malfunction?any ideas?thanks in advance
|
|
|
Post by wb1983 on Jan 14, 2024 11:55:10 GMT
Hi all,
I'm trying to access central elec 09 to enable my rer view camera, however I get security code access denied.
It's for a 2017 S3.
Does anybody know the code, please?
Regards
Wayne.
|
|
|
Post by whataboutthis on Jan 14, 2024 16:50:18 GMT
See my answer to you other question.
|
|