|
|
Post by blikstjinder on Feb 12, 2021 21:05:38 GMT
Seat Leon ST 2020 FR - new model
Software Version: 1664
//the below Confirmed\\
2/ Lane Assist Point Of Intervention: thanks to tommy95
- Select Module A5 (Driver Assistance) ->
- Select Long Coding ->
- Select Point Of Intervention ->
- Set To Early
4/ Remaining Fuel Quantity
1 - Select Control Unit 17 - Instrument panel (Dashboard)
2 - -Select Long Coding- >> go to Adaptions
3 - Adjust Volume to be replenished: Set to Yes if you want to see it. If you have it and don't want it then change to No
Offroad View in the Dashboard:
In 17-Dashboard
go to Adaptions
Set Offroad to Display
Go to View Activation
Change the setting in View_10 to active.
>> only see wheel angle in left side view
1/ Adding new views to cockpit
This was identified firstly on FR Cars showing and there are some cars where these changes did not work.
- Select Control unit 17 (Dashboard)
- Select Long Coding
- Select View Activation
- Tick the non active Views
>> Cupra view added
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 12, 2021 22:35:43 GMT
@bilkstjinder thanks for sharing thats very helpful, have you tried any of the mods on Control unit 09.
|
|
|
|
Post by blikstjinder on Feb 13, 2021 7:32:36 GMT
@testeronline
Yes I tried but I can’t access l.coding or adaptations.
So we need to wait for that.
I’ll still try other stuff in te coming weeks.
Steve
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 13, 2021 8:12:44 GMT
blikstjinder thanks steve that confirms this control unit is locked down for now
Just found another tool that is supporting SFD and I notice they quote the following changes
Seat belt warning off/changed
Control Unit 17 - Long Coding - Text Version (0) -
Select Seat belt warning - Default is Version 1 (European) you can change it to Version 2 (US) or Off
Speed Warning
Control Unit 17 - Long Coding - Text Version (0) -
Speed warning - Default is off on the car i have access to but can be changed to On
Lap timer
Control Unit 17 - Long Coding - Text Version (0) -
Lap Counter - Default is on for the car i have access to but can be changed to Off
Staging
Please note on the Leon's in the past the early dashboards did not support this
Control Unit 17 - Long Coding - Text Version (0) -
Staging - Default is on for the car i have access to is No but can be changed to Yes
Oil Temp Display
Control Unit 17 - Long Coding - Text Version (0) -
Oil temperature display - Set to Yes
Add extra detail to the Tacho
previously this did Original the tacho only displays 0-20-40-60-80-100-etc you can change this so it also (in a smaller font) displays 10-30-50-70 etc. thanks to @denabl
Control Unit 17 - Long Coding - Text Version (0) -
Tachometer erweiterte skalenteilung - Set to Yes
Saves the last temperature of the Heated seats
With this mod, the temperature set in the last instance in the seats will be saved for when you start the car again.
1 - Module 08 - Air conditioning / heating electronics
2 - Adaptation
3 - Retention of driver's seat heater level - Default set to Active for 10 Minutes can be changed to Not Active or Active
4 - Retention of frt.pass. seat heater level - Default set to Active for 10 Minutes can be changed to Not Active or Active
Automatic activation for windscreen de-icing
With this mod, when starting the car if the cold conditions are adequate, the air conditioner will start blowing to the windshield by default to defrost it.
1 - Module 08 - Air conditioning
2 - Adaptations
3 – Automatic Activation of front windshield heater at MAX-Defrost -
4 - Change value to Active
|
|
|
|
Post by blikstjinder on Feb 14, 2021 22:47:55 GMT
This is not working for me;
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 15, 2021 14:52:00 GMT
blikstjinder did you get error or just it saves but does not work - thanks.
|
|
|
|
Post by blikstjinder on Feb 15, 2021 21:58:43 GMT
It saved successfully and is now active but isn’t working.
|
|
|
|
Post by peterhell on Feb 21, 2021 22:45:23 GMT
Driver Assistance 1/ Deactivate overtaking right prevention - Thanks to zelue1995 - Select Control Unit 13 - Select Long Coding (0) - Select overtaking_right_prevention - Change from activated to Deactivated 2/ Lane Assist Point Of Intervention: thanks to tommy95 - Select Module A5 (Driver Assistance) ->
- Select Long Coding ->
- Select Point Of Intervention ->
- Set To Early
3/ Lane Assist Warnings: thanks to tommy95 - Select Module A5 (Driver Assistance) - Select Long Coding - Select Lane Assist Off Text - Change to Set To Disabled
4/ Lane Assist Settings: thanks to tommy95 - Select Module A5 (Driver Assistance) -> - Select Long Coding ->
- Select Configuration For Lane Departure Warning K15 ->
- Set To Last Setting
5/ Deactivate Stop Start
Disabling Stop Start thanks to Phipilipipp on the seat-leon.de forum
I have seen that some users have problems with this coding on MK3 but It has been confirmed that it works fine on MK4.
- Select Control Unit 08 (Air Conditioning)
- Select Adaptation
- Select Deactivation of Start Stop Function
Please note I have got this code from the German Forum, I also had seen this working on the MK3 and some Audi cars. Two guys on the Skoda thread say it dont work for them so all I can think is this is Firmware related.
Virtual Cockpit
1/ Adding new views to cockpit - thanks to darthmike This was identified firstly on FR Cars showing and there are some cars where these changes did not work.
- Select Control unit 17 (Dashboard)
- Select Long Coding
- Select View Activation
- Tick the non active Views
This will display various model (eg FR, Cupra etc) in rev counter
- Select Control unit 17-Dashboard -
- Select Adaptions
- Select Logo menu
- select one of the logo items:
On the Golf8 the following is known.
logo_1 and logo_2 are for the R
Logo_3 for GTE
logo_4 for GTI
logo_5 for GTD
3/ Change ICE Warning temperature - Now confirmed on the Golf by massimo23
With this mod, you can change the warning temperatures of possible danger of ice.
1 - Select Control Unit 17 - Instrument panel -
2 - Select Adaptation
3 - Select outside_temperature:
4 - Adjust p_ice_warning_exit_temperature: - (Change value to the desired one - By default 6ºC)
5 - Adjust p_ice_warning_entry_temperature:- (Change value to the desired one - By default 4ºC)
4/ Remaining Fuel Quantity thanks to massimo23
1 - Select Control Unit 17 - Instrument panel (Dashboard)
2 - Select Long Coding
3 - Adjust Volume to be replenished: Set to Yes if you want to see it. If you have it and don't want it then change to No
5/ Change the Display in 4/ above to different measure
1 - Select Control Unit 17 - Instrument panel (Dashboard)
2 - Select Long Coding 3 - Select Volume 4 - Chose between Liter, gallons (US) or gallongs (UK)
Hello I am trying to disable the Stop / Start on my MY21 T-Roc and Changing the battery voltage to 12.1 is definitely not working the car still stops and re starts. It is stopping the engine immediately after starting the engine from cold ambient temperature 15c. I used gateway 19 Adaptions Search start Set Battery voltage to 12.1 Will any updated Apps be produced to sort this out for 2021 models? Thank you for any help. Regards Peter |
|
|
|
Post by peterhell on Feb 21, 2021 22:46:08 GMT
.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 21, 2021 23:00:05 GMT
Hello I am trying to disable the Stop / Start on my MY21 T-Roc and Changing the battery voltage to 12.1 is definitely not working the car still stops and re starts. It is stopping the engine immediately after starting the engine from cold ambient temperature 15c. I used gateway 19 Adaptions Search start Set Battery voltage to 12.1 Will any updated Apps be produced to sort this out for 2021 models? Thank you for any help. Regards Peter the voltage fix has been turned off by vw sp no longer works Personally I fitted a memory module to solve this problem but i dont know if you have a switch on the new cars. this coding works for some but not all 5/ Deactivate Stop Start Disabling Stop Start thanks to Phipilipipp on the seat-leon.de forum I have seen that some users have problems with this coding on MK3 but It has been confirmed that it works fine on MK4. - Select Control Unit 08 (Air Conditioning) - Select Adaptation - Select Deactivation of Start Stop Function Please note I have got this code from the German Forum, I also had seen this working on the MK3 and some Audi cars. Two guys on the Skoda thread say it dont work for them so all I can think is this is Firmware related. |
|
|
|
Post by peterhell on Feb 21, 2021 23:09:48 GMT
Hi to make the aircon fix work do you have to have the aircon switched on all the time??
Thank you for your help
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 21, 2021 23:13:22 GMT
yes thats what i have been told
|
|
|
|
Post by peterhell on Feb 22, 2021 1:24:27 GMT
Hi
I have a switch for the stop start which memory module did you get
to switch off stop start??
Thanks for your help
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 22, 2021 8:37:52 GMT
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 25, 2021 15:08:36 GMT
New release today
Changelog
v0.34.1
- Fixed an issue where some control units were not detected for Golf MK8 and i presume this is the Leon 4 as well.
The following control units were missing so hopefully now they will be shown.
05-Acc/Start Auth
D6-Light Ctrl Left 2
D7-Light Ctrl Right 2
|
|
|
|
Post by massimo23 on Feb 25, 2021 22:34:02 GMT
I will try it then, great news. What about the subsystems in 09 Central electric can these be shown too?
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 25, 2021 22:36:05 GMT
the release notes as always are poor, i am afraid you will have to try as see if it works if not report to support please
I should also add that IOS had the same upgrade applied.
But today we have yet another release so no idea whats in that one.
|
|
|
|
Post by france84 on Feb 28, 2021 22:31:33 GMT
Hi guys, I bought my Seat Leon 4° series on September 2020. Could you tell me if it's a my2020 or my2021? Differences between the two versions?
Software installed is 1664, no way to update it (at least I think so, I tried many times with esim, also with tethering by mobile, but the car doesn't find any update).
I also tried to activate the views locked, it worked and was easy, but nothing changed trying to set logo adaptions. I tried logo 1, 2 and 5...no positive result. Any for you?
The same with control 17 "volume to be replenished": no effects (in main front cockpit view it was already set, but not near the picture).
Again, setting yes in control 17 "tachometer erweiterte skalenteilung", nothing changed.
In unit control 8, adaption, deactivation start&stop, once again no results (start&stop in infotainment is always set as ON, it appears to be just delayed when you brake to stop, but not really deactivated). I'd like to have it in OFF position when I start the engine, instead the actual automatic ON.
Last, but not least, seat belt warning requires a code to be changed. Do you know that code? Obd app doesn't suggest me anything (while when I deactivated the "overtaking right prevention" was suggested by app for the code that was needed.
Thanks a lot!
|
|
|
|
Post by schwoebbes on Mar 4, 2021 11:56:31 GMT
Hello, i‘m new to this forum, since i recently bought my fr and have the obdeleven now for around 2 weeks.
Tried coding the lane assist so far and it works okay.
No function under 60 km/h but above that it works well.
I changed the setting for the warning to „last setting“ and now i just get the red warning signal but way to often and the only way to deactivate it is with a little wiggle, which is annoying. So i will try to deactivate it completely.
I found some long coding belonging to matrix led but didn‘t activate it right now.
I also found a table with all the login codes for the mqb series i would like to share if i can upload it here somewhere.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Mar 4, 2021 12:40:58 GMT
thanks for update
but as far as we I know they don't apply to mqb evo platform (only because when I have seen others try using them they did not work) there is one code known for that
Update
and i should add I am happy to be proved wrong but dont have access to New car so cant test the old codes fully.
|
|
joiko
New Member
Posts: 3
|
Post by joiko on Mar 10, 2021 8:09:08 GMT
Hi! Did it ask you for a code to be able to access that module?
Thanks!
|
|
joiko
New Member
Posts: 3
|
Post by joiko on Mar 10, 2021 16:51:22 GMT
“Point of intervention” > Early >> CONFIRMED << Works like a charm. Now I need to know how I can disable the warning to put your hands on the steering wheel. 😝 Does anyone know? Hi! I activated that option, but where can I see if its working?? I have lane assist by default but you said this is travel assists, can you post a picture? or a process that how to activate in obd eleven? Im new in this... Thanks! |
|
|
|
Post by blikstjinder on Mar 10, 2021 22:03:58 GMT
Hi joikoAfter you turned this on you just need to drive. Once the car recognizes the road lines. Showed in the dashboard it wil take over. If you take the highway soon enough it will ask you to take over the steering wheel. It is really precise so you hardly need to steer anymore. At least in my case. |
|
|
|
Post by france84 on Mar 10, 2021 22:37:46 GMT
I activated it as well, it really works stopping "bouncing" between lanes, but the same problem for me: it always warns that you have to keep hands on steering wheel.
|
|
|
|
Post by newty on Mar 11, 2021 19:16:04 GMT
A5 should not have SFD at this time.
Regarding ALG or at least something similiar:
Maybe we should try HC Variante to change.
there are plenty of settings, but I only saw 0 (basic lane assist) and 2 (travel assist with travel assist button on steering wheel). Maybe somebody can try 1 or other values? My mqbevo is said to arrive this may, so I still have to wait until I can try myself
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Mar 13, 2021 18:34:54 GMT
Thanks to maypack for confirming that on his Formentor (same platform) you can turn of the silly sound actuator. Select Control unit A9 (Structure Borne Sound) Select Adaptation Select Volume of structure-borne noise actuator Select % you want 0 to turn it off or reduced to lower sound. |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Mar 20, 2021 18:01:27 GMT
Thanks to tell @ www.seatcupra.net/forums/threads/obd-modifications.463977/#post-4961854Untested on Evo Platform but on the car i have in my garage this is already set and the Golf8 cars don't have this setting unless I am being blind. Lane assist systems is a bit annoying that once it is turned off in maxidot menu - assistance systems, it turns back on upon cycling a key. However this is the coding that prevents this from happening: -> Control Unit A5 - Driver Assistance -> select Long coding -> Select option 0 -> change setting Perso_HC from Activated to Last_setting or -> Select option 1 -> Select Byte 13 -> Tick bit 3 and ensure Bit 2 is unticked Save. tip: in case you get the error when saving -> (31) function not available, change the mode to vw - diagnostic mode, and try again (even if you are already using this mode, just reselect it again) Once activated, the car will remember the last state of Lane assist (on or off) upon cycling the key.  |
|
|
|
Post by elcocheseat on Mar 22, 2021 9:29:38 GMT
Tried it, and it works on my KL ST.
|
|
|
|
Post by cioce on Mar 22, 2021 11:40:11 GMT
I activated it as well, it really works stopping "bouncing" between lanes, but the same problem for me: it always warns that you have to keep hands on steering wheel.
It's normal, cars with travel assist optional have a capacitive steering wheel, that you don't have!
|
|
|
|
Post by newty on Mar 24, 2021 8:28:59 GMT
A5 should not have SFD at this time. Regarding ALG or at least something similiar: Maybe we should try HC Variante to change. there are plenty of settings, but I only saw 0 (basic lane assist) and 2 (travel assist with travel assist button on steering wheel). Maybe somebody can try 1 or other values? My mqbevo is said to arrive this may, so I still have to wait until I can try myself Maybe somebody can try this? Maybe another value here provides a better lane assist. |
|
