|
|
Post by toffel86 on Dec 18, 2017 18:26:34 GMT
Hallo,
Ich habe den Facelift 2017 leon.Finde leider kein Menüpunkt mit Access Control 2 unter Module09/Adaption.Oder nennt sich das in der Deutschen Version wieder anders?
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Dec 18, 2017 18:42:55 GMT
Hallo, die Facelift-Modelle (2017) haben unterschiedliche Kodierungen, bitte schaut euch das N Forum obdeleven.proboards.com/board/215/ an und ihr werdet die neue Kodierung sehen. Sie können auch das FL Golf Forum für mehr Codierung besuchen. |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Dec 23, 2017 20:15:38 GMT
Just seen this on the Seat site www.seatcupra.net/forums/showpost.php?p=4755908&postcount=9, If you have keyless entry in your car or a standard key but want the remote control to work when engine is running then set the following. 1/ go to Control unit: 09 Central Electrics 2/ Adaptions 3/ Go to access control 4/ Take Funk bei Klemme 15 ein and set to Active nb you may have to enter a security code in which case use 31347 This for keyless entry this should allow you to have the car running but lock the door whilst you are outside. For non keyless cars you will be able to use your fob whilst the car is running, so for example you can open your boot whilst sitting in the drivers seat with engine running. I should point out for UK users this will be illegal and almost certainly invalidate your insurance because you have left the car running with you not in it. As with all changes that I share you make these at your own risk |
|
|
|
Post by Freak0815 on Jan 4, 2018 9:19:39 GMT
Ist es eigentlich möglich die ambientebeleuchtung zu ändern wenn der rückwärtsgang eingelegt wird? Danach sollte die alte farbe wieder sein
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 4, 2018 19:09:31 GMT
This is the only coding I have seen for this
Ambient light blank door with reverse
With this mod, carrying the doors in red, when putting the reverse gear will go blank.
Leerraumtür des Umgebungslichtes mit Rückseite
Mit diesem Mod wird das Tragen der Türen in Rot, wenn der Rückwärtsgang eingelegt wird, leer.
1 - Module 09 - Electronic control unit. Code (31347)
2 - Adaptation
3 - Select - Leuchte16BLK SLB35BLK SL KC9
4 - Submenu - Lichtfunktion G 16
5 - Change value to Rückfahrlicht
6 - Select - Leuchte16BLK SLB35BLK SL KC9
7 - Submenu - Dimmwert GH 16
8 - Change value to 0
9 - Select - Leuchte16BLK SLB35BLK SL KC9
10 - Submenu - Dimming direction GH 16
11 - Change value to Minimize
12 - Select - Leuchte17TFL R BLK SRB3TFL R BLK SR KC3
13 - Submenu - Lichtfunktion C 17
14 - Change value to Rückfahrlicht
15 - Select - Leuchte17TFL R BLK SRB3TFL R BLK SR KC3
16 - Submenu - Dimmwert CD 17
17 - Change value to 127
18 - Select - Leuchte17TFL R BLK SRB3TFL R BLK SR KC3
19 - Submenu - Dimming direction CD 17
20 - Change value to Maximized
NOTE: Leuchte 16 is the red light (0 and minimized = 127 and maximized) and Leuchte 17 is white light (0 and minimized = 127 and maximized)
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 16, 2018 16:48:01 GMT
Simple change that enables you to remove from AM from your radio list (AM, FM, DAB by Default)
select Control unit: 5F Information Control Unit
Select long Coding
Ensure you are still in mode 0 (top right hand of the screen)
Select byte_14_AM_disable
Change from Not activated (Default) to activated
The AM Frequency will no longer be shown on your Radio Frequency List.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 19, 2018 16:36:37 GMT
Just keeping all the changes in one place to make it easier to find. Below link show you how to adjust or disable the front light washers to help reduce water consumption. obdeleven.proboards.com/post/11746 |
|
|
|
Post by leon2014 on Feb 6, 2018 13:29:51 GMT
This coding, however, allows only the closing of the windows, but not of the sunroof
Close windows to detect rainIf you leave the car with the windows down and starts to rain, the car automatically closes the windows 1 - Module 09 - Electronic. Code (31347) 2 - Adaptation 3 - Select - Access Control 2 4 - Sub - ein aus Regenschliessen 6 - Change value to Active 7 - Sub - Menuesteuerung regenschliessen 8 - Change value to Active 9 - Sub - Regenschliessen art 10 - Change value to Permanent 11 - extended Coding (Bytes Mode) 12 - Byte 0 13 - Enable Bits 1 and 2 There's an error in this instruction. Should be: 11 - go to Subsystems 12 - choose RLFS (or RLS - according to some source newer RLHS doesn't support rain closing) 13 - coding 14 - byte 0 15 - Enable Bits 1 and 2 I don't know what bits 1 and 2 of byte 0 of Central Electronics module do, but certainly do not enable rain closing function. Enabling those bits on RLFS subsystem however does enable that function. Also according to some sources it's required to perform factory reset of the "closing" subsystem via car menu. I did that just to be sure, and now rain closing seems to be working fine. |
|
|
|
Post by toffel86 on Feb 7, 2018 11:15:55 GMT
Nope factory reset of the "closing" subsystem via car menu dont work for me  |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 7, 2018 12:22:50 GMT
Nope factory reset of the "closing" subsystem via car menu dont work for me Toffel86 sorry but what are you trying to resolve and just to confirm is your car a pre facelift one. |
|
|
|
Post by toffel86 on Feb 7, 2018 12:56:56 GMT
Facelift 17/18 i try to activate rainclose. All Windows close,but not the sunroof  |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 7, 2018 16:20:46 GMT
ok just check out the coding on the N forum (as that is the Facelift one)
From the Golf Forum (thanks to VWJAP) I have the following code for facelift golf's with roof
Go to [09] Central Electronics
Go to Secuity Access and enter 31347
Go to adaptation channels and set the following:
- (15) Access Control 2 - Regenschliessen_ein aus (Rain Closing on / off) - Select Active
- (16) Access Control 2 - Regenschliessen_art (Rain closing Type) set to Permanent
- (28) Access Control 2 - Menuesteuerung Regenschliessen (Menu Control Rain close) – Set to Active (enables the menu in the ifotainment screen)
9 Central Electronics
Rain and light sensor (could be RLS or RHLS subsystem)
Byte 0…Enable Bit 2 “Regenschliessen aktiv”. (rain closing active)
Bit 1 should be active too….Regenlicht aktiv (rain light active)
My Old coding…..00A8DD
My New coding….06A8DD
But access control 2 on the new module is ZV Komfort
Then you have to select in MIB
And you have to have the wipers in automatic position
But it doesn’t work on some cars (different rain sensor?)
I haven’t done this myself tho,
|
|
|
|
Post by toffel86 on Feb 7, 2018 17:41:13 GMT
Hm the same coding i have done.but i dont have the wipers in automatic position.because its work in off position but without roof.maybe thats the problem.i will try it.thanks a lot
|
|
|
|
Post by toffel86 on Feb 8, 2018 14:34:22 GMT
Dont work
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 8, 2018 16:29:25 GMT
ok afraid I dont have the roof on my car, and just to double check you are pre facelift.
Going through the coding there are a number of codes for Panoramaschiebedachbeleuchtung which is to do with lighting but hopefully something simular may help.
The other thing to look for is DACH which is roof so there may be something there.
I will have a look tonight on the web but I do know that there is more than one sort of rain sensor and this does not always work.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 8, 2018 19:06:28 GMT
just seen this on youtube
STG 09, 31347, Adaption, Access control 2-SAD Richtung Komfortoeffnen, set "Open" or "tilting"
Not sure if this is tied in with the rain closing.
Afraid all the vids I have seen say it does not work on the roof.
|
|
|
|
Post by nike2002 on Feb 13, 2018 9:07:34 GMT
hello I have a 5f of 2017 I would need to modify the ice in the fis from the beginning 4 to 2 degrees the code 25327 and 20103 do not work.
thank you
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 13, 2018 10:22:15 GMT
nike2002 this is the pre facelift board you should post this question on the N board.
However just in case it has not changed this is the coding for our cars
Modify grades warning of possible danger ice
With this mod, you can change temperatures warning of possible danger of ice.
1 - Module 17 - Code Box instruments- (25327)
2 - Adaptation
3 - Select - Outside temperature
4 - Search option - P exit temperature ice warning
5 - Modify the desired value: 6 ° C Default
6 - Search option - P ice warning entry temperature:
7 - Modify the desired value: 4 ° C Default
|
|
|
|
Post by nike2002 on Feb 13, 2018 10:57:37 GMT
nike2002 this is the pre facelift board you should post this question on the N board. However just in case it has not changed this is the coding for our cars Modify grades warning of possible danger ice With this mod, you can change temperatures warning of possible danger of ice. 1 - Module 17 - Code Box instruments- (25327) 2 - Adaptation 3 - Select - Outside temperature 4 - Search option - P exit temperature ice warning 5 - Modify the desired value: 6 ° C Default 6 - Search option - P ice warning entry temperature: 7 - Modify the desired value: 4 ° C Default tried and tried again but it is not accepted without giving error or otherwise. |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 13, 2018 11:15:33 GMT
Just checked the Golf Forum and found this forum.obdeleven.com/post/10017the comment that may be relevant is OK, so now for the bad news answer! To change the value in the 2 x adaptation channels above, you will need a security access code. This code was 20103 in early versions of the dashboard module, but I'm not aware that the code has been found for newer modules. Happy to be proven wrong |
|
|
|
Post by nike2002 on Feb 13, 2018 13:45:20 GMT
Just checked the Golf Forum and found this forum.obdeleven.com/post/10017the comment that may be relevant is OK, so now for the bad news answer! To change the value in the 2 x adaptation channels above, you will need a security access code. This code was 20103 in early versions of the dashboard module, but I'm not aware that the code has been found for newer modules. Happy to be proven wrong thanks for the effort but I also tried 2-4 but the code does not work |
|
|
|
Post by andy1977 on Feb 17, 2018 11:05:18 GMT
I was hoping somebody might be able to take a min to explain what the following coding will achieve?
Flashing LED DRL dissipated.
Flashing lights DRL with LED simultaneous.
Against stage lights DRL with LED lights appr forward.
Rear lights flashing in sequence mode (LED drivers)
Thanks
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 22, 2018 23:42:04 GMT
I was hoping somebody might be able to take a min to explain what the following coding will achieve? Flashing LED DRL dissipated. check out the last bit of this thread obdeleven.proboards.com/thread/2034/drl-led-dissipated\Flashing lights DRL with LED simultaneous. I am guessing its the opposite of the below one.Against stage lights DRL with LED lights appr forward. With this modification you can make the lights do the following: When the flashing light DRL are off and when the indicator is off the DRL light. It is very cool.Rear lights flashing in sequence mode (LED drivers) Check out obdeleven.proboards.com/thread/2071/rear-blinkers-coding-video not sure if this is the coding you are talking about
Bottom line its very easy to code these changes, and if you dont like what they do then just put it back as it was before.
Take a backup of your settings before you start so you have an easy reference point to do the reverse if required.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 22, 2018 23:45:56 GMT
Just checked the Golf Forum and found this forum.obdeleven.com/post/10017the comment that may be relevant is OK, so now for the bad news answer! To change the value in the 2 x adaptation channels above, you will need a security access code. This code was 20103 in early versions of the dashboard module, but I'm not aware that the code has been found for newer modules. Happy to be proven wrong thanks for the effort but I also tried 2-4 but the code does not work Check out DV52 Answer on ways to find a new code, and if you do then please share so other users can use it. forum.obdeleven.com/post/13385 |
|
|
|
Post by chry81 on Feb 23, 2018 9:44:31 GMT
Hi, someone may me help to understand what is the correct coding for oil for a QG1
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 23, 2018 10:17:23 GMT
Hi, someone may me help to understand what is the correct coding for oil for a QG1 You should have an app that does this for 10 credits (vs your 6 free credits a day) Reset oil change warning With this mod you can reset the oil change notice. 1 - Applications 2 - Oil service reset 3 - Select the desired Hope that helps |
|
|
|
Post by funolivier on Mar 19, 2018 21:31:53 GMT
Hi guys,
Thanks for this thread ! I owned a Leon 5F manufactured in January 2016. I don't have OBDeleven (perhaps i should have...) , but VCDS 18.X.
I have three questions on the mods offered here:
** "Folding mirrors. On-Screen Activation[...]**"
=> To be sure. With single press on the lock buton of the remote control, mirrors will fold and windows will close ? Whats the meaning of "The Settings main screen is activated."?
** "Close windows to detect rain" **
It does not work with my car. I have now an option displayed in the head pannel, but after a "water test", nothing happens... I ve seen it can be due to latest sensors on Leon. I choosed "RLFS", should i have choosen RLS ?
Is it possible to enable the "sleepness assistant" (sorry don't know how translate in english)? You know, i'm talking about the cup of coffee picture display if the car assumes you are falling asleep...
Thanks very much
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Mar 19, 2018 23:12:34 GMT
funolivier as you are a VCDS Guy you should really be asking these questions on the Ross Tech sites (if you are not registered you should do so but only if you have a genuine cable or you will not get any help at all). With regards to Folding mirrors. On-Screen Activation With this mod, the windows are raised and the mirrors are folded without having to be continuously pressing the button of the remote. 1 - Module 09 - Electronic control unit. Code (31347) 2 - Adaptation 3 - Select - Access control 2 4 - Submenu - Menuesteuerung funk spiegel anklappen - Options (Inactive - Activated) 5 - Change value to On The Settings main screen is activated. - So this allows you to close windows and mirrors are folded but it also adds another menu option to your settings under car, cant recall what it gives you but have a look on the screen.
Never been interested in this one so not tried it but here is the coding I have
Close windows to detect rain
If you leave the car with the windows down and starts to rain, the car automatically closes the windows
1 - Module 09 - Electronic. Code (31347)
2 - Adaptation
3 - Select - Access Control 2
4 - Sub - ein aus Regenschliessen
6 - Change value to Active
7 - Sub - Menuesteuerung regenschliessen
8 - Change value to Active
9 - Sub - Regenschliessen art
10 - Change value to Permanent
11 - extended Coding (Bytes Mode)
12 - Byte 0
13 - Enable Bits 1 and 2
Some sites show the Golf 7 Coding works here as well
There's an error in this instruction.
Should be:
11 - go to Subsystems
12 - choose RLFS (or RLS - according to some source newer RLHS doesn't support rain closing)
13 - coding
14 - byte 0
15 - Enable Bits 1 and 2
I don't know what bits 1 and 2 of byte 0 of Central Electronics module do, but certainly do not enable rain closing function.
Enabling those bits on RLFS subsystem however does enable that function.
Also according to some sources it's required to perform factory reset of the "closing" subsystem via car menu.
I did that just to be sure, and now rain closing seems to be working fine.
I presume you only have RLFS or RLS as a subsystem not both but as I say not done it so not checked it out.
It should be possible to code fatigue detection but i have not seen any coding yet, although there is a thread here that may help you forum.obdeleven.com/thread/1812/awareness-assist-activation
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Mar 24, 2018 17:35:51 GMT
Another member asked me to see if i could help with the indicator lights being on full time. Just a warning in the UK and some other countries this is illegal so be aware and I am not sure if the bulbs like being on full time but just sharing what I found. My setup shown below  and here is the video showing what it looks like when indicating And a still picture of setup when not indicating  |
|
hitz
Closed beta tester
Posts: 1
|
Post by hitz on Mar 25, 2018 23:03:41 GMT
Another member asked me to see if i could help with the indicator lights being on full time. Just a warning in the UK and some other countries this is illegal so be aware and I am not sure if the bulbs like being on full time but just sharing what I found. My setup shown below and here is the video showing what it looks like when indicating And a still picture of setup when not indicating hello, i found a way on vcds, steps should be the same as follow with obd11: [09 – Centrale Electrique] -> [Security Access – 16] 31347 -> [Adaptation – 10] -> « (8)-Leuchte 0 BLK VL B36-Lichtfunktion C 0 » select « Standlicht allgemein (Schlusslitch; Positionslicht; Begrenzungslicht) » [09 – Centrale Electrique] -> [Security Access – 16] 31347 -> [Adaptation – 10] -> « (8)-Leuchte1BLK VRB20-Lichtfunktion C 1 » select « Standlicht allgemein (Schlusslitch; Positionslicht; Begrenzungslicht) » [09 – Centrale Electrique] -> [Security Access – 16] 31347 -> [Adaptation – 10] -> « (10)-Leuchte 0 BLK VL B36-Dimmwert CD 0 » Set a value between 0 and 100 (lighting of the lights between 0 and 100%) [09 – Centrale Electrique] -> [Security Access – 16] 31347 -> [Adaptation – 10] -> « (10)-Leuchte1BLK VRB20-Dimmwert CD 1 » Set a value between 0 and 100 (lighting of the lights between 0 and 100%) [09 – Centrale Electrique] -> [Security Access – 16] 31347 -> [Adaptation – 10] -> « (12)-Leuchte 0 BLK VL B36-Lichtfunktion E 0 » select « Blinken links Dunkelphase » [09 – Centrale Electrique] -> [Security Access – 16] 31347 -> [Adaptation – 10] -> « (15)-Leuchte 0 BLK VL B36-Dimming Direction EF 0 » select « minimize » [09 – Centrale Electrique] -> [Security Access – 16] 31347 -> [Adaptation – 10] -> « (12)-Leuchte1BLK VRB20-Lichtfunktion E 1 » select « Blinken rechts Dunkelphase » [09 – Centrale Electrique] -> [Security Access – 16] 31347 -> [Adaptation – 10] -> « (15)-Leuchte1BLK VRB20-Dimming Direction EF 1 » select « minimize » if someone wanna try, should work, before try do a backup! please can some1 post me a photo of original settings? wanna be sure i didnt changed anything wrong, thanks. Dan~ |
|
