|
|
Post by vwcalifornia on Jan 9, 2018 6:58:53 GMT
In the end I found it, the problem was that some of the app is translated, others are not.
It's working fine.
Greetings.
|
|
|
|
Post by vwjap on Jan 15, 2018 23:06:23 GMT
Thanks, But I tried three times, always flashes when I lock and unlock the doors, I try each option on the page you suggestions me. I d'ont understand why we have acoustic confirmation lock/unlock in apps, but not visual confirmation on/off option ? had another little look, found this Central electronics Aussenlicht_Blinker: ZV_Blinken_zu: active ZV_Blinken_auf: active ZV is central locking, Blinken is blinkers, zu + Auf is on and off. That’s in my google translate 😂😂 |
|
|
|
Post by dv52 (Australia) on Jan 16, 2018 5:19:40 GMT
Here's my instructions from VWWatercooled for the mk7 - it should be the same for mk7.5 (I think)
OBD11 Instructions: Front DRLs flash with lock/unlock
If the car has LED "angel-eyes" headlight fittings:
1. Select Central electrics module @ address hex09
2. Select security access
3. Enter the magic number 31347
4. Select adaptations
5. For a late-model module search for Außenlicht_Blinker. If you have an early-model module, search for Dyn. turn signal modes
6. Select Warnblinken_Zuendung_EIN change to active
7. Select Warnblinken_Zuendung_AUS change to active
8. Search for Leuchte2SL VLB10 (this is the left-side angel-eye)
9. Select Lichtfunktion G 2. ONLY IF THE VALUE IS not active, change to Aktive Blinkfunktion hat ein auf 1 gesetztes zugeordnetes Bit in pa_dynamisch_blinken
10. Select Dimmwert GH 2, change value to 100 (default 0)
11. Search for Leuchte3SL VRB21 (this is the right-side angel-eye)
12. Select Lichtfunktion G 3. ONLY IF THE VALUE IS not active, change to Aktive Blinkfunktion hat ein auf 1 gesetztes zugeordnetes Bit in pa_dynamisch_blinken
13. Select Dimmwert GH 3, change value to 100 (default 0)
If the car has incandescent headlight fittings:
1. Swap reference to Leuchte2SL VLB10 to Leuchte4TFL LB4 (note: Lichtfunktion G 2 becomes Lichtfunktion G 4 and Dimmwert GH 2 becomes Dimmwert GH 4)
2. Swap reference to Leuchte3SL VRB21 to Leuchte5 TFL RB32 (note: Lichtfunktion G 3 becomes Lichtfunktion G 5 and Dimmwert GH 3, becomes Dimmwert GH 5)
Don
|
|
|
|
Post by vwjap on Jan 16, 2018 8:01:08 GMT
Don, he wanted to turn off indicators flashing with door lock/unlock
|
|
|
|
Post by russellhiltonnel on Jan 16, 2018 8:56:37 GMT
Thanks Don I'll give this one a try on the weekend. Like the concept. Wonder if my back leds will flash in sync as i done Scandinavian led mod already
|
|
|
|
Post by dv52 (Australia) on Jan 17, 2018 0:46:04 GMT
Thanks Don I'll give this one a try on the weekend. Like the concept. Wonder if my back leds will flash in sync as i done Scandinavian led mod already russell: Hi. No- alas my tweak instructions are meant only for the front DRLs, but it ain't difficult to extend the facility to any other lamp. Once you have activated the Warnblinken_Zuendung_EIN/AUS facility on your car, you can make any lamp "acknowledge" lock/unlock by adding the Aktive Blinkfunktion hat ein auf 1 gesetztes zugeordnetes Bit in pa_dynamisch_blinken command to an unused alpha channel in the associated Leuchte-set. So, for example - if you want to flash the rear outer turn-signal LEDs to acknowledge lock/unlock: - Search for Leuchte18BLK HLA60 (this is the Leuche-set for the left-side outer rear turn signal LED)
- Select Lichtfunktion G 18. ONLY IF THE VALUE IS not active, change to Aktive Blinkfunktion hat ein auf 1 gesetztes zugeordnetes Bit in pa_dynamisch_blinken
- Select Dimmwert GH 18, change value to 100 (default 0)
- Search for Leuchte19BLK HRC31 (this is the Leuchte-set for the right-side outer rear turn signal LED)
- Repeat steps 2 and 3 above
Don
|
|
kart
New Member
Posts: 9 
|
Post by kart on Jan 17, 2018 2:21:54 GMT
Thanks, But I tried three times, always flashes when I lock and unlock the doors, I try each option on the page you suggestions me. I d'ont understand why we have acoustic confirmation lock/unlock in apps, but not visual confirmation on/off option ? had another little look, found this Central electronics Aussenlicht_Blinker: ZV_Blinken_zu: active ZV_Blinken_auf: active ZV is central locking, Blinken is blinkers, zu + Auf is on and off. That’s in my google translate 😂😂I'll try tonight I'll be back tomorrow, I'm crossing my fingers... Thanks you very much for your assistance and your patience. |
|
|
|
Post by russellhiltonnel on Jan 17, 2018 8:58:05 GMT
Thanks Don I'll give this one a try on the weekend. Like the concept. Wonder if my back leds will flash in sync as i done Scandinavian led mod already russell: Hi. No- alas my tweak instructions are meant only for the front DRLs, but it ain't difficult to extend the facility to any other lamp. Once you have activated the Warnblinken_Zuendung_EIN/AUS facility on your car, you can make any lamp "acknowledge" lock/unlock by adding the Aktive Blinkfunktion hat ein auf 1 gesetztes zugeordnetes Bit in pa_dynamisch_blinken command to an unused alpha channel in the associated Leuchte-set. So, for example - if you want to flash the rear outer turn-signal LEDs to acknowledge lock/unlock: - Search for Leuchte18BLK HLA60 (this is the Leuche-set for the left-side outer rear turn signal LED)
- Select Lichtfunktion G 18. ONLY IF THE VALUE IS not active, change to Aktive Blinkfunktion hat ein auf 1 gesetztes zugeordnetes Bit in pa_dynamisch_blinken
- Select Dimmwert GH 18, change value to 100 (default 0)
- Search for Leuchte19BLK HRC31 (this is the Leuchte-set for the right-side outer rear turn signal LED)
- Repeat steps 2 and 3 above
Don
Thanks mate will give it a whirl. Mod & Mod often is my mantra |
|
|
|
Post by Carolco on Jan 17, 2018 22:23:12 GMT
And to actívate the others front drl lights?
|
|
kart
New Member
Posts: 9
|
Post by kart on Jan 18, 2018 2:54:30 GMT
Here's my instructions from VWWatercooled for the mk7 - it should be the same for mk7.5 (I think)
OBD11 Instructions: Front DRLs flash with lock/unlock If the car has LED "angel-eyes" headlight fittings:1. Select Central electrics module @ address hex09 2. Select security access3. Enter the magic number 313474. Select adaptations5. For a late-model module search for Außenlicht_Blinker. If you have an early-model module, search for Dyn. turn signal modes6. Select Warnblinken_Zuendung_EIN change to active7. Select Warnblinken_Zuendung_AUS change to active8. Search for Leuchte2SL VLB10 (this is the left-side angel-eye) 9. Select Lichtfunktion G 2. ONLY IF THE VALUE IS not active, change to Aktive Blinkfunktion hat ein auf 1 gesetztes zugeordnetes Bit in pa_dynamisch_blinken10. Select Dimmwert GH 2, change value to 100 (default 0) 11. Search for Leuchte3SL VRB21 (this is the right-side angel-eye) 12. Select Lichtfunktion G 3. ONLY IF THE VALUE IS not active, change to Aktive Blinkfunktion hat ein auf 1 gesetztes zugeordnetes Bit in pa_dynamisch_blinken13. Select Dimmwert GH 3, change value to 100 (default 0) If the car has incandescent headlight fittings:1. Swap reference to Leuchte2SL VLB10 to Leuchte4TFL LB4 (note: Lichtfunktion G 2 becomes Lichtfunktion G 4 and Dimmwert GH 2 becomes Dimmwert GH 4) 2. Swap reference to Leuchte3SL VRB21 to Leuchte5 TFL RB32 (note: Lichtfunktion G 3 becomes Lichtfunktion G 5 and Dimmwert GH 3, becomes Dimmwert GH 5) DonPerfect, I'll try this just now! Thank you Don !!!  It does not work : I do not know what changes because I did not see any difference? Central electronics Aussenlicht_Blinker: ZV_Blinken_zu: active ZV_Blinken_auf: active |
|
kart
New Member
Posts: 9
|
Post by kart on Jan 18, 2018 3:06:11 GMT
Here's my instructions from VWWatercooled for the mk7 - it should be the same for mk7.5 (I think)
OBD11 Instructions: Front DRLs flash with lock/unlock If the car has LED "angel-eyes" headlight fittings:1. Select Central electrics module @ address hex09 2. Select security access3. Enter the magic number 313474. Select adaptations5. For a late-model module search for Außenlicht_Blinker. If you have an early-model module, search for Dyn. turn signal modes6. Select Warnblinken_Zuendung_EIN change to active7. Select Warnblinken_Zuendung_AUS change to active8. Search for Leuchte2SL VLB10 (this is the left-side angel-eye) 9. Select Lichtfunktion G 2. ONLY IF THE VALUE IS not active, change to Aktive Blinkfunktion hat ein auf 1 gesetztes zugeordnetes Bit in pa_dynamisch_blinken10. Select Dimmwert GH 2, change value to 100 (default 0) 11. Search for Leuchte3SL VRB21 (this is the right-side angel-eye) 12. Select Lichtfunktion G 3. ONLY IF THE VALUE IS not active, change to Aktive Blinkfunktion hat ein auf 1 gesetztes zugeordnetes Bit in pa_dynamisch_blinken13. Select Dimmwert GH 3, change value to 100 (default 0) If the car has incandescent headlight fittings:1. Swap reference to Leuchte2SL VLB10 to Leuchte4TFL LB4 (note: Lichtfunktion G 2 becomes Lichtfunktion G 4 and Dimmwert GH 2 becomes Dimmwert GH 4) 2. Swap reference to Leuchte3SL VRB21 to Leuchte5 TFL RB32 (note: Lichtfunktion G 3 becomes Lichtfunktion G 5 and Dimmwert GH 3, becomes Dimmwert GH 5) Don Just to be certain, I have a Golf R 2018 (facelift, with the new headlights) I do not know if that's what you call angel-eyes? And in my case, I want the turn-signal LEDs to remain OFF!! when I lock and unlock the doors. Thank you! |
|
|
|
Post by Blindek on Jan 18, 2018 21:04:57 GMT
You don't need to code this, there should be a setting in thr car for this. Visual lock unlock confirmation or something like that
|
|
|
|
Post by ozgur on Jan 24, 2018 7:45:48 GMT
hello 2017 new case golf 7 I installed the light and rain sensor. But when it comes to coding, the values of center electronics in long code are 0000000.
09 Center needs to do the electrical adaptation part. please help me
|
|
|
|
Post by ozgur on Jan 24, 2018 7:46:39 GMT
1 Fault Found:
919560 - Light Switch
B126A 29 [009] - Signal Implausible
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 3
Fault Frequency: 6
Reset counter: 53
Mileage: 4048 km
Date: 2017.12.29
Time: 18:10:00
|
|
|
|
Post by vwjap on Jan 24, 2018 8:45:16 GMT
Long coding is 0000000000 but subsystems are
Subsystems:
Subsystem: WWS 161207
Long coding: 0E4DDD
Subsystem: RLHS
Long coding: 00A8DD
Plus there are some adaptions too
|
|
|
|
Post by ozgur on Jan 24, 2018 9:08:42 GMT
Can you please indicate where these codings will be inserted in the attached picture which belong to my car? Can you share the adaptions of coding? Thank you for your cooperation.  |
|
|
|
Post by vwjap on Jan 24, 2018 9:57:41 GMT
There is NO long coding for the central electronics, so that screen is correct, there is 2 subsystems in the long coding that are coded (see above post)
dunno where the subsystems on VCDS fella (well it is a obdeleven board)
|
|
|
|
Post by vwjap on Jan 24, 2018 10:06:53 GMT
Assistance light functions:
Regen_Lichtsensor:
LIN_Regen_Licht_Sensor
Feuchtesensor:
installed
Assistenzfahrlicht bei Regen:
active
Sonnensensor:
not installed
LS_Error_Ausgabe:
active
Maskierung_Regenfunktion:
not active
Lichtsensorempfindlichkeit:
normal
Light sensor:
Einschaltgrenze_CHO_LHO:
600 lx
Daemmerungsgrenze, Hysterese_obergrenze:
1200 lx
Daemmerungsgrenze_Hysterese_untergrenze:
2200 lx
Helligkeitsgrenze_sehr_hell:
2000 lx
Helligkeitsgrenze_Licht__einschalten:
1200 lx
Helligkeitsgrenze_Licht_ausschalten:
2200 lx
Minimale_Beleuchtungsstaerke:
0 lx
Maximale_Beleuchtungsstaerke:
0 lx
Minimale_Ausgangsspannung:
0 mV
Maximale_Ausgangsspannung:
0 mV
Tunnel_einschalt_verzoegerung:
2
ECE_Lichteinschaltschwelle:
0 lx
Helligkeitsgrenze_Licht_ausschalten_red:
0
HMI_Wiper_Comfort_Rain_Sensor_OFF:
not active
HMI_Exterior_light_on_highway:
not active
HMI_Exterior_light_on_rain:
not active
LS_Error_Ausgabe:
not active
HMI_exterior_light_sensitivity:
frueh
Suchbeleuchtung_Fotosensor:
x0:
0
x1:
50
x2:
100
x3:
200
x4:
253
x5:
0
x6:
0
x7:
0
x8:
0
x9:
0
x10:
0
y0:
0 lx
y1:
50 lx
y2:
100 lx
y3:
200
y4:
500
y5:
0
y6:
0 lx
y7:
0 lx
y8:
0 lx
y9:
0 lx
y10:
0 lx
Suchbeleuchtung_KL 58xs min:
x0:
0 lx
x1:
8 lx
x2:
50 lx
x3:
510 lx
y0:
6.0
y1:
6.0
y2:
100.0
y3:
100.0
Suchbeleuchtung_KL 58xs max:
x0:
0 lx
x1:
8 lx
x2:
50 lx
x3:
500 lx
y0:
100.0
y1:
100.0
y2:
100.0
y3:
100.0
Suchbeleuchtung_Regen_Licht_Sensor_Mapping_Kennlinie:
x0:
0 lx
x1:
10 lx
x2:
100 lx
x3:
500 lx
x4:
800 lx
x5:
1020 lx
y0:
0
y1:
20
y2:
80
y3:
180
y4:
300
y5:
500
RLS_wiper_position_parking:
15 s
RLS_close_glazing:
2.0 s
RLS_lights_for_autobahn:
p_v_autobahn_on:
140 km/h
p_v_autobahn_off:
65 km/h
p_t_autobahn_delay_on:
10 s
p_t_autobahn_delay_off:
120 s
RLS_Washer_Front:
15 s
RLS_LIN_Communication:
4 s
RLS_tunel_gateway_recognize:
5 s
RLS_Lights_on_at_Rain:
p_n_regenlichtschwelle_high:
12
p_n_regenlichtschwelle_low:
6
p_lx_regenlichtschwelle:
6000 lx
p_t_regenlicht:
30 s
RLS_Night_Sensitivity:
p_lx_rs_day:
500 lx
p_lx_rs_dawn:
200 lx
Dunno if there's any more fella
|
|
|
|
Post by ozgur on Jan 24, 2018 11:39:21 GMT
I cross-checked with my car's, and i have shown below the differences with red color.
I think it is sufficient to change these in adaptations.
IDE08786-ENG115723-Assistance light functions-Assistenzfahrlicht bei Regen,active ,9
IDE08786-ENG115724-Assistance light functions-Lichtsensorempfindlichkeit,normal ,9
IDE08786-ENG126628-Assistance light functions-LS_Error_Ausgabe,active ,9
IDE08786-ENG142228-Assistance light functions-Maskierung_Regenfunktion,not active ,9
IDE08786-ENG141985-Assistance light functions-Regen_Lichtsensor,not installed ,9 -------- LIN_Regen_Licht_Sensor Feuchtesensor: installed
IDE08786-ENG124476-Assistance light functions-Sunlight Sensor,not installed ,9
MAS08228-ENG133434-Light sensor-Daemmerungsgrenze: Hysterese_obergrenze,1200 lx,24
MAS08228-ENG133435-Light sensor-Daemmerungsgrenze_Hysterese_untergrenze,2200 lx,24
MAS08228-ENG133444-Light sensor-ECE_Lichteinschaltschwelle,0 lx,24
MAS08228-ENG133433-Light sensor-Einschaltgrenze_CHO_LHO,600 lx,24
MAS08228-ENG133437-Light sensor-Helligkeitsgrenze_Licht__einschalten,1200 lx,24
MAS08228-ENG133438-Light sensor-Helligkeitsgrenze_Licht_ausschalten,2200 lx,24
MAS08228-ENG133445-Light sensor-Helligkeitsgrenze_Licht_ausschalten_red,00 00 ,24
MAS08228-ENG133436-Light sensor-Helligkeitsgrenze_sehr_hell,2000 lx,24
MAS08228-ENG142230-Light sensor-HMI_Exterior_light_on_highway,not active ,24
MAS08228-ENG142231-Light sensor-HMI_Exterior_light_on_rain,not active ,24
MAS08228-ENG142232-Light sensor-HMI_exterior_light_sensitivity,frueh ,24
MAS08228-ENG142229-Light sensor-HMI_Wiper_Comfort_Rain_Sensor_OFF,not active ,24
MAS08228-ENG126628-Light sensor-LS_Error_Ausgabe,not active ,24
MAS08228-ENG133442-Light sensor-Maximale_Ausgangsspannung,0 mV,24
MAS08228-ENG133440-Light sensor-Maximale_Beleuchtungsstaerke,0 lx,24
MAS08228-ENG133441-Light sensor-Minimale_Ausgangsspannung,0 mV,24
MAS08228-ENG133439-Light sensor-Minimale_Beleuchtungsstaerke,0 lx,24
MAS08228-ENG133443-Light sensor-Tunnel_einschalt_verzoegerung,02 ,24
ENG122927-RLS_close_glazing,2.0 s,1
ENG122928-ENG121637-RLS_lights_for_autobahn-p_t_autobahn_delay_off,120 s,3
ENG122928-ENG121636-RLS_lights_for_autobahn-p_t_autobahn_delay_on,10 s,3
ENG122928-ENG121635-RLS_lights_for_autobahn-p_v_autobahn_off,65 km/h,3
ENG122928-ENG121634-RLS_lights_for_autobahn-p_v_autobahn_on,140 km/h,3
ENG122931-ENG123004-RLS_Lights_on_at_Rain-p_lx_regenlichtschwelle,6000 lx,2
ENG122931-ENG123002-RLS_Lights_on_at_Rain-p_n_regenlichtschwelle_high,12 ,2
ENG122931-ENG123003-RLS_Lights_on_at_Rain-p_n_regenlichtschwelle_low,6 ,2
ENG122931-ENG123005-RLS_Lights_on_at_Rain-p_t_regenlicht,30 s,2
ENG122929-RLS_LIN_Communication,4 s,1
ENG122932-ENG123007-RLS_Night_Sensitivity-p_lx_rs_dawn,100 lx,1 ----------- 200lx
ENG122932-ENG123006-RLS_Night_Sensitivity-p_lx_rs_day,200 lx,1 ----------- 500lx
ENG122930-RLS_tunel_gateway_recognize,5 s,1
ENG122935-RLS_Washer_Front,15 s,1
ENG122926-RLS_wiper_position_parking,15 s,1
ENG141667-ENG115658-Suchbeleuchtung_Fotosensor-x0,0 ,22
ENG141667-ENG101574-Suchbeleuchtung_Fotosensor-X1,50 ,22
ENG141667-ENG115664-Suchbeleuchtung_Fotosensor-x10,0 ,22
ENG141667-ENG99557-Suchbeleuchtung_Fotosensor-X2,100 ,22
ENG141667-ENG102140-Suchbeleuchtung_Fotosensor-X3,200 ,22
ENG141667-ENG102936-Suchbeleuchtung_Fotosensor-X4,253 ,22
ENG141667-ENG103548-Suchbeleuchtung_Fotosensor-X5,0 ,22
ENG141667-ENG113992-Suchbeleuchtung_Fotosensor-X6,0 ,22
ENG141667-ENG115661-Suchbeleuchtung_Fotosensor-x7,0 ,22
ENG141667-ENG115662-Suchbeleuchtung_Fotosensor-x8,0 ,22
ENG141667-ENG115663-Suchbeleuchtung_Fotosensor-x9,0 ,22
ENG141667-ENG115659-Suchbeleuchtung_Fotosensor-y0,0 lx,22
ENG141667-ENG99777-Suchbeleuchtung_Fotosensor-Y1,50 lx,22
ENG141667-ENG115668-Suchbeleuchtung_Fotosensor-y10,0 lx,22
ENG141667-ENG100480-Suchbeleuchtung_Fotosensor-Y2,100 lx,22
ENG141667-ENG100773-Suchbeleuchtung_Fotosensor-Y3,200 ,22
ENG141667-ENG100631-Suchbeleuchtung_Fotosensor-Y4,500 ,22
ENG141667-ENG102174-Suchbeleuchtung_Fotosensor-Y5,0 ,22
ENG141667-ENG113993-Suchbeleuchtung_Fotosensor-Y6,0 lx,22
ENG141667-ENG115665-Suchbeleuchtung_Fotosensor-y7,0 lx,22
ENG141667-ENG115666-Suchbeleuchtung_Fotosensor-y8,0 lx,22
ENG141667-ENG115667-Suchbeleuchtung_Fotosensor-y9,0 lx,22
ENG141669-ENG115658-Suchbeleuchtung_KL 58xs max-x0,0 lx,8
ENG141669-ENG101574-Suchbeleuchtung_KL 58xs max-X1,8 lx,8
ENG141669-ENG99557-Suchbeleuchtung_KL 58xs max-X2,50 lx,8
ENG141669-ENG102140-Suchbeleuchtung_KL 58xs max-X3,500 lx,8
ENG141669-ENG115659-Suchbeleuchtung_KL 58xs max-y0,100.0 ,8
ENG141669-ENG99777-Suchbeleuchtung_KL 58xs max-Y1,100.0 ,8
ENG141669-ENG100480-Suchbeleuchtung_KL 58xs max-Y2,100.0 ,8
ENG141669-ENG100773-Suchbeleuchtung_KL 58xs max-Y3,100.0 ,8
ENG141668-ENG115658-Suchbeleuchtung_KL 58xs min-x0,0 lx,8
ENG141668-ENG101574-Suchbeleuchtung_KL 58xs min-X1,8 lx,8
ENG141668-ENG99557-Suchbeleuchtung_KL 58xs min-X2,50 lx,8
ENG141668-ENG102140-Suchbeleuchtung_KL 58xs min-X3,510 lx,8
ENG141668-ENG115659-Suchbeleuchtung_KL 58xs min-y0,6.0 ,8
ENG141668-ENG99777-Suchbeleuchtung_KL 58xs min-Y1,6.0 ,8
ENG141668-ENG100480-Suchbeleuchtung_KL 58xs min-Y2,100.0 ,8
ENG141668-ENG100773-Suchbeleuchtung_KL 58xs min-Y3,100.0 ,8
ENG141680-ENG115658-Suchbeleuchtung_Regen_Licht_Sensor_Mapping_Kennlinie-x0,0 lx,12
ENG141680-ENG101574-Suchbeleuchtung_Regen_Licht_Sensor_Mapping_Kennlinie-X1,10 lx,12
ENG141680-ENG99557-Suchbeleuchtung_Regen_Licht_Sensor_Mapping_Kennlinie-X2,100 lx,12
ENG141680-ENG102140-Suchbeleuchtung_Regen_Licht_Sensor_Mapping_Kennlinie-X3,500 lx,12
ENG141680-ENG102936-Suchbeleuchtung_Regen_Licht_Sensor_Mapping_Kennlinie-X4,800 lx,12
ENG141680-ENG103548-Suchbeleuchtung_Regen_Licht_Sensor_Mapping_Kennlinie-X5,1020 lx,12
ENG141680-ENG115659-Suchbeleuchtung_Regen_Licht_Sensor_Mapping_Kennlinie-y0,0 ,12
ENG141680-ENG99777-Suchbeleuchtung_Regen_Licht_Sensor_Mapping_Kennlinie-Y1,20 ,12
ENG141680-ENG100480-Suchbeleuchtung_Regen_Licht_Sensor_Mapping_Kennlinie-Y2,80 ,12
ENG141680-ENG100773-Suchbeleuchtung_Regen_Licht_Sensor_Mapping_Kennlinie-Y3,180 ,12
ENG141680-ENG100631-Suchbeleuchtung_Regen_Licht_Sensor_Mapping_Kennlinie-Y4,300 ,12
ENG141680-ENG102174-Suchbeleuchtung_Regen_Licht_Sensor_Mapping_Kennlinie-Y5,500 ,12
|
|
|
|
Post by vwjap on Jan 24, 2018 11:43:56 GMT
I might have a different sensor to you so maybe leave the 200-500lx as yours are (presume it’s only how bright it is when sun rises/sets, so you might not get “switch on headlights” as early as my car), but defo find the long coding subsystem (rhls one) and set that too
|
|
|
|
Post by ozgur on Jan 24, 2018 11:50:25 GMT
"vwjap" user helped me on adaptations and gave the below codings. Thank you very much.
Now i need to know where the below subsystems are on VCDS.
Long coding is 0000000000 but subsystems are
Subsystems:
Subsystem: WWS 161207
Long coding: 0E4DDD
Subsystem: RLHS
Long coding: 00A8DD
Plus there are some adaptions too
|
|
|
|
Post by vwjap on Jan 24, 2018 12:15:58 GMT
|
|
|
|
Post by vwjap on Jan 26, 2018 19:35:28 GMT
Just in case it annoys you when driving up the motorway and there’s a lane hog in the right lane and you don’t like your car slowing down to his speed  acc long coding byte 02 (bit 5 ticked) overtaking_right_prevention set it from active to not active |
|
|
|
Post by vwjap on Feb 1, 2018 15:55:32 GMT
Turn off kessy locking/unlocking
Startsystems
Long coding
Activation of kessy door handle, driver door
Activation of kessy door handle, ft pass door
Change to not installed
|
|
|
|
Post by webtrak on Feb 1, 2018 23:22:33 GMT
The off road display didn't work for my 2017 Alltrack SE.
|
|
ins90
New Member
Posts: 1
|
Post by ins90 on Feb 2, 2018 7:09:25 GMT
Me too, with my 2018 sport
|
|
|
|
Post by vwjap on Feb 3, 2018 12:06:03 GMT
On the background lighting page the slider at the bottom (not the colour one) is the brightness one (sometimes you have to press the all areas button) there's also a off button (set Ambientemenue mit globalem aus -active) Did you get the AID working then? Yes did it today and got it working I'm pretty sure we can still have independent footwell lighting and door lighting I was thinking something new needs to be enabled as on the background lighting page there is in a section to control all which is both together, Im sure we should be able to activate something which will let us choose which one individually as it says select an area but there is only all to chose from Vwjap you may know more So finally got a car with adjustable independent footwell and door strip 09 central electronics admap, I have found a difference but 1) it won’t let me change it (comes up “something went wrong”) and 2) it’s in binary (e.g 00111100) whereas it will only let you change from 0-255, bugger |
|
|
|
Post by opolat on Feb 3, 2018 14:20:12 GMT
Hi vwjap I did the operation you mentioned above and introduced the sensors. I can not find how the light switch is activated Thanks |
|
|
|
Post by OBDeleven on Feb 7, 2018 8:13:14 GMT
Yes did it today and got it working I'm pretty sure we can still have independent footwell lighting and door lighting I was thinking something new needs to be enabled as on the background lighting page there is in a section to control all which is both together, Im sure we should be able to activate something which will let us choose which one individually as it says select an area but there is only all to chose from Vwjap you may know more So finally got a car with adjustable independent footwell and door strip 09 central electronics admap, I have found a difference but 1) it won’t let me change it (comes up “something went wrong”) and 2) it’s in binary (e.g 00111100) whereas it will only let you change from 0-255, bugger Can you send error report after you get “something went wrong" message? To send report press three dots in top right corner and select report error function. |
|
|
|
Post by vwjap on Feb 7, 2018 12:07:44 GMT
So finally got a car with adjustable independent footwell and door strip 09 central electronics admap, I have found a difference but 1) it won’t let me change it (comes up “something went wrong”) and 2) it’s in binary (e.g 00111100) whereas it will only let you change from 0-255, bugger Can you send error report after you get “something went wrong" message? To send report press three dots in top right corner and select report error function. done |
|
