|
|
Post by hama1234567 on Jul 10, 2022 22:26:43 GMT
Hello previously my car has aftermarket mk7.5 headlight and i returned to oem mk7 (14pin) bi-xenon headlight xenon and drl working without error but my headlight presentation movement and static cornering light not working.. and on headlight regulation basic setting i need to restore to original calibration not working (sorry my english not good i hope understand ) |
|
|
|
Post by dv52 (Australia) on Jul 11, 2022 23:45:51 GMT
hama1234567 : At least for the calibration error - see my post (4th post) HERE
Don
|
|
|
|
Post by hama1234567 on Jul 12, 2022 14:27:26 GMT
|
|
|
|
Post by dv52 (Australia) on Jul 13, 2022 6:04:14 GMT
Yes, calibration requires that the module is operating correctly- so you won't be able to run the process until you attend to the DTCs.
It appears the right side module is isn't working - no output and not coded!! Why?
Also, does the car actually have 2 x level sensors - because this is what you have told the hex55 module via long-code string.
And why does the car believe the RH/LH drive changeover switch has been operated?
Don
|
|
|
|
Post by hama1234567 on Jul 13, 2022 7:42:03 GMT
The 2x level sensor the left side working when i checked by output test . And idon’t know RH/LH Can I turned of?
If I change the module dou you think the it will work what part number or module software require . Thanks don
|
|
|
|
Post by dv52 (Australia) on Jul 13, 2022 10:20:53 GMT
Not sure about your front-left level sensor- but clearly the hex55 module doesn't think that it's functioning correctly. Is it new- if so, are you sure it's the correct unit?
For the right-side module errors - before you spend any more money, try swapping left and right side modules. Then redo the auto-scan. Does the DTC follow the swapped module. If so, then you might need to replace the module. If not, the error is somewhere else.
Note: it's better when sourcing these modules to get a second-hand unit from a donor car that has the same drive-side (rather than a brand-new) because used modules are already parameterized.
For the other error, I'm fairly certain that you can access the LHD/RHD changeover switch via the car MENU. This from the owner's manual: - The headlight orientation can be adjusted using the CAR button and the
 and Light function buttons in the infotainment system .
If the MENU on your car doesn't have this function, you can do the same thing with your diagnostic device like this: - Fire-up the diagnostic device (OBD11, VCDS, etc) and connect to the dongle
- Select the hex55 module
- click-on Adaptation
- Select Activate left/right hand drive switch-over and change value to not active
Don
|
|
|
|
Post by hama1234567 on Jul 13, 2022 10:47:19 GMT
Thanks bro i will follow you instructions i will swap the (afs) module . If the module not working .if I buy the module it must be the same part number of the other one ?or no! and my cornering light not working i check fuse and replaced the h7 bulb |
|
|
|
Post by hama1234567 on Jul 14, 2022 17:33:25 GMT
update// i swapped the right afs module to left headlight seems not working and the left one also not working on the right headlight . and the (C1082 31) fault code disappear but new code shown and i looked on both module below the date number written (0591) the other one (3236) .. sorry my english not good i hope you understand . auto scan ww.txt (1.77 KB)   |
|
|
|
Post by dv52 (Australia) on Jul 15, 2022 2:07:23 GMT
Not sure what's happening and it really depends on the headlights - but here is an example of how the auto-scan should be:
------------------------------------------------------------------------------- Address 55: Headlight Range (J745) Labels:| 7P6-907-357.clb Part No SW: 7P6 907 357 D HW: 7P6 907 357 A Component: AFS-ECU H07 0090 Revision: -------- Serial number: -------------- Coding: 029602000B000200 Shop #: WSC 01357 011 00200 ASAM Dataset: EV_HeadlRegulVWAFSMQB 001120 ROD: EV_HeadlRegulVWAFSMQB.rod VCID: 40D949FA9A06F7EBE71-8014 Left Headlamp Power Output Stage: Subsystem 1 - Part No SW: 3D0 941 329 D HW: 3D0 941 329 D Labels: 3D0-941-329.CLB Component: LeiMo links H01 0002 Coding: 2E0000 Right Headlamp Power Output Stage: Subsystem 2 - Part No SW: 3D0 941 329 E HW: 3D0 941 329 E Labels: 3D0-941-329.CLB Component: LeiMo rechts H01 0002 Coding: 2E0000 ---------------------------------------------------------------------------------------------------------------------------------------
I suggest that you return the output modules to their original sides - then re-enter the long-code string into the hex55 module - copy and paste the same value back into the module (don't use the long-code value above). Sometimes, this will re-program the long-code string back into the left/right side Power Output modules
Don
|
|
|
|
Post by hama1234567 on Jul 15, 2022 9:40:51 GMT
i just opened the module of the right side it seems blown.  
i will order new one .. it has to be same part number or not ? ? ? ? ? ? |
|
|
|
Post by hama1234567 on Jul 16, 2022 14:26:10 GMT
hello today ihave installed the new module (3D0 941 329 E) Component: LeiMo rechts H01 0002 my right side fault disappear .and ihave the same fault on left sight idon't know why when i start the car the movment start with old module .and right side no functioning with new module Scan-WVWFK2AU8FW001002-20220716-1551-206382....txt (2.03 KB) |
|
