|
|
Post by loik91 on Jul 25, 2020 7:57:38 GMT
 Hi, i've an issue with the light of the button doesn't "light up". for your information. only 2 screw to remove the central console and 2 other for the button. very easy but really take precautions to remove the central console, it's only one part with the comfort screen :/ . =) |
|
|
|
Post by loik91 on Jul 25, 2020 9:01:27 GMT
and this one on 19 gateway:
Adresse 19: Gateway
1 Code défaut trouvé:
528129 - Bus de données
U1121 00 [008] - message manquant
[NVEM_BMS_NV_01_Timeout_Failure]
Intermittent - Confirmé - Testé depuis RàZ mémoire
Does somebody have an idea?
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jul 25, 2020 14:28:07 GMT
Hi, i've an issue with the light of the button doesn't "light up". for your information. only 2 screw to remove the central console and 2 other for the button. very easy but really take precautions to remove the central console, it's only one part with the comfort screen :/ . =) This is really amazing. This is my first time to see the P button not the AI button. What is the part number for this? |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jul 25, 2020 14:35:50 GMT
Hi, i've an issue with the light of the button doesn't "light up". for your information. only 2 screw to remove the central console and 2 other for the button. very easy but really take precautions to remove the central console, it's only one part with the comfort screen :/ . =) Also when you mentioned "light of the button doesn't "light up".", are you referring to the background light (the white light) or the actual function light (the bar at top)? |
|
|
|
Post by loik91 on Jul 26, 2020 0:07:23 GMT
It's J the newer version. The bar on top of the button. And after some reset and one 1/6 starting i've an a5 odometer error...  |
|
|
|
Post by andreask on Jul 26, 2020 5:38:10 GMT
Hi, i've an issue with the light of the button doesn't "light up". for your information. only 2 screw to remove the central console and 2 other for the button. very easy but really take precautions to remove the central console, it's only one part with the comfort screen :/ . =) Well Done, nice to see what you did! Except from one or a few errors - is your park assist now fully functional?? |
|
|
|
Post by loik91 on Jul 27, 2020 18:05:36 GMT
i've a question :
why we didn't activate any byte in 01 module or 02 because when i check the blockmap a see "ipa gearbox function = no "
Do you have an idee where we can activate this?
For the moment i didnt have yet the SWA function and i think my odometer error was from this missing. (I need to remove my réar bumper and seat :/
So maybe next week with motivation ^^)
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jul 27, 2020 21:15:00 GMT
i've a question : why we didn't activate any byte in 01 module or 02 because when i check the blockmap a see "ipa gearbox function = no " Do you have an idee where we can activate this? For the moment i didnt have yet the SWA function and i think my odometer error was from this missing. (I need to remove my réar bumper and seat :/ So maybe next week with motivation ^^) This is a really good finding since the new parking assist will control the gear for us. I believe we have talk to matt (if I recall correctly ), he is the guy that got most closely to active the function. |
|
|
|
Post by loik91 on Jul 28, 2020 17:39:43 GMT
Hi,
after buy one hour on erwin,(wich is really very informative but in german. And i choose spanish at school :,( if someone have some basics...)
What I understood:
We need corner front/rear sensor as i assumed.
"FRONT:4N0 997 669 F and REAR:4N0 907 566 E"
After that "stp"(normaly) and ipa can be used because we've all module for autonome parking.
A6/A8 are absolutely the same module. Except the "13 module sensor" not at the same place.
I'ld like to know Who have bought/or order the button?
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jul 28, 2020 18:03:24 GMT
Hi, after buy one hour on erwin,(wich is really very informative but in german. And i choose spanish at school :,( if someone have some basics...) What I understood: We need corner front/rear sensor as i assumed. "FRONT:4N0 997 669 F and REAR:4N0 907 566 E" After that "stp"(normaly) and ipa can be used because we've all module for autonome parking. A6/A8 are absolutely the same module. Except the "13 module sensor" not at the same place. I'ld like to know Who have bought/or order the button? I have Q8 and "FRONT:4N0 997 669 F" is standard equipment in Q8 for crossing assist. I don't think A6 has this radar. For the rear one, any car with blind spot assist will have that radar. I really want to buy that button but they are not going to sell that in Canada.  |
|
|
|
Post by loik91 on Jul 28, 2020 18:33:21 GMT
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jul 28, 2020 20:31:58 GMT
I see. A6 has it DB-Frt Corner Rdar 1 -- Status: OK 0000 DC-Frt Corner Rdar 2 -- Status: OK 0000 |
|
matt
Junior Member
Posts: 68
|
Post by matt on Aug 1, 2020 18:22:07 GMT
i've a question : why we didn't activate any byte in 01 module or 02 because when i check the blockmap a see "ipa gearbox function = no " Do you have an idee where we can activate this? For the moment i didnt have yet the SWA function and i think my odometer error was from this missing. (I need to remove my réar bumper and seat :/ So maybe next week with motivation ^^) This is a really good finding since the new parking assist will control the gear for us. I believe we have talk to matt (if I recall correctly ), he is the guy that got most closely to active the function. So with my current coding (that I had posted) I have no errors. Did you have errors before adding the button, or just after? Does the park assist button show up on the lower MMI screen for you? Wish I could get my hands on a button, alas no luck in the US |
|
|
|
Post by davedavez on Aug 2, 2020 2:11:08 GMT
mattThe button is available in the US from europrice.us. He quoted me $165 plus shipping. I've used him for parts before and it's always quick and well priced. (as well priced as Audi parts can be.) I was holding off on buying one myself until you gave us the word you got it working. 😂
|
|
matt
Junior Member
Posts: 68
|
Post by matt on Aug 3, 2020 14:03:55 GMT
Can you link me to the product page? I'm unable to find it
|
|
|
|
Post by davedavez on Aug 3, 2020 16:36:32 GMT
There is no product page, you just email him with the Audi part number you want and he'll quote you.
|
|
denbal
Junior Member
Posts: 61
|
Post by denbal on Aug 11, 2020 23:44:44 GMT
Hey guys,
i've coded everything like been said here.
De soft button pops up on the lower screen, and also in the areaview-screen.
I can activate it, and it does seem to find parking spots.
But also asks for the AI button then.
The button is ordered and i expect it by the end of the week.
Very curious if someone has a fully working park assist yet ?
Because i'm having brake problems with the manouver assist, i assume this will also starts playing up with the park assist unfortunately.
 |
|
Sky
New Member
Posts: 26
|
Post by Sky on Aug 12, 2020 9:20:37 GMT
denbal
Congratulations^^
Can you post your coded values?
|
|
|
|
Post by tempos84 on Aug 12, 2020 13:35:13 GMT
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 17, 2020 14:38:27 GMT
matt The button is available in the US from europrice.us. He quoted me $165 plus shipping. I've used him for parts before and it's always quick and well priced. (as well priced as Audi parts can be.) I was holding off on buying one myself until you gave us the word you got it working. 😂 I ordered the button from oemvwshop.com for $99usd plus shipping. www.oemvwshop.com/4n0959673j-4n0959673j-p2564358/?currency=usd 
Installing the button was a breeze. I had removed the console once before to upgrade the cup holder assembly. I wrote up the below for anyone unsure of the process. 2019 A6 Parking Assist Button Installation: This will take 30 minutes to an hour to complete. 1. Slide driver and passenger seats back and as low as possible. 2. Remove the snap on side panels from the center console, starting at the forward end (under the dash). - You can leave the rear end of the panels connected to the rear storage compart for easy reassembly. 3. Disconnect large Molex connector on each side of the center console. 4. Using a Torx 20 bit (I think it was a 20) to remove 2 screws on each side of the console (1 forward, 1 rear end). 5. Pop screw cover out from the bottom of the cup hold and remove the T20 screw. 6. Remove the gear shift knob. a. Remove snap-on trim from the top of the shifter knob. b. Remove T20 screw c. Remove shifter knob by pulling straight up (the leatherette is attached and will pop out of the console with the knob). 7. Lift the console up a few inches from the rear end (i.e., at the storage compartment). - Before lifting too far, reach under and disconnect the black parking break wiring connector from bottom of the console. 8. Carefully pull out console enough to turn on it's side and disconnect the cable from rear of existing switch assembly, and the final cable from behind the monitor (use a soft cloth to protect the screen). - Disconnecting the final cable is optional, but this makes it much easer to change the switch. If you disconnect the final cable, you can take the whole console to your workbench or kitchen table... 9. Disconnect the three connectors on the rear of the existing switch assembly. 10. Push the old switch assembly forward until it pops out of the console. 11. Remove the old switch from the switch module assembly by releasing four tabs with a small flat head screw driver - replace with new switch. 12. Follow above steps in reverse to re-install the console. 13. Turn on ignition and Test! Verify the parking break error and any other dash errors clear. 14. Done! |
|
|
|
Post by davedavez on Aug 17, 2020 19:03:00 GMT
I saw that too, but am very skeptical. I've never seen a discount that steep on an Audi part. Let us know when it arrives so we can all jump on it if it's the right one.
|
|
|
|
Post by ustolle on Aug 18, 2020 18:50:25 GMT
News from kufatec.com www.kufatec.com/en/assist-park/park-assist/upgrade-park-pilot-audi-a6-4a-a7-4k-a8-4n-q7-q8-4m-e-tron-ge-44920function of the park pilot Functions of the Park Pilot: Activation of the park pilot in the MMI and scanning of a suitable parking space using the sensors while driving (max. 40 km/h) Press and hold the button in the center console, the vehicle takes over the parking process completely (incl. gas and brake) Graphical representation of the route by the cameras Releasing the button causes the parking process to stop immediately suitable for the following vehicles: Audi A6 4A Audi A7 4K Audi A8 4N Audi Q7 4M as of model year 2020 Audi Q8 4M Audi e-tron GE only suitable for vehicles with area view (PR No.: KA6) as well as park distance control (PR No.: 9X0) |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 18, 2020 18:51:48 GMT
I saw that too, but am very skeptical. I've never seen a discount that steep on an Audi part. Let us know when it arrives so we can all jump on it if it's the right one. It actually arrived a day early. Here are some photos...  |
|
|
|
Post by davedavez on Aug 18, 2020 21:28:18 GMT
Fantastic, thanks for the update! $99 is an acceptable gamble to see if we can get the coding working. If you do the install yourself, let us know how it goes.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 18, 2020 22:35:32 GMT
Good news from Kufatec but it seems that they are not ready with this retrofit kit since they are looking for a beta tester and this kit is not for sale yet. The price is attractive but it includes the trial installation in their HQ in Bad Segeberg.
What worries me a bit is that their retrofit kit includes also additional wiring harness. Does it mean that "P" button and appropriate coding is not enough?
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 19, 2020 2:54:40 GMT
Fantastic, thanks for the update! $99 is an acceptable gamble to see if we can get the coding working. If you do the install yourself, let us know how it goes. Installing the button was a breeze. I had removed the console once before to upgrade the cup holder assembly. I wrote up the below for anyone unsure of the process. 2019 A6 Parking Assist Button Installation: This will take 30 minutes to an hour to complete. 1. Slide driver and passenger seats back and as low as possible. 2. Remove the snap on side panels from the center console, starting at the forward end (under the dash). - You can leave the rear end of the panels connected to the rear storage compart for easy reassembly.3. Disconnect large Molex connector on each side of the center console. 4. Using a Torx 20 bit (I think it was a 20) to remove 2 screws on each side of the console (1 forward, 1 rear end). 5. Pop screw cover out from the bottom of the cup hold and remove the T20 screw. 6. Remove the gear shift knob. a. Remove snap-on trim from the top of the shifter knob. b. Remove T20 screw
c. Remove shifter knob by pulling straight up (the leatherette is attached and will pop out of the console with the knob).
7. Lift the console up a few inches from the rear end (i.e., at the storage compartment).
- Before lifting too far, reach under and disconnect the black parking break wiring connector from bottom of the console.
8. Carefully pull out console enough to turn on it's side and disconnect the cable from rear of existing switch assembly, and the final cable from behind the monitor (use a soft cloth to protect the screen).
- Disconnecting the final cable is optional, but this makes it much easer to change the switch. If you disconnect the final cable, you can take the whole console to your workbench or kitchen table...
9. Disconnect the three connectors on the rear of the existing switch assembly.
10. Push the old switch assembly forward until it pops out of the console.
11. Remove the old switch from the switch module assembly by releasing four tabs with a small flat head screw driver - replace with new switch.
12. Follow above steps in reverse to re-install the console.
13. Turn on ignition and Test! Verify the parking break error and any other dash errors clear.
14. Done!
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 19, 2020 12:05:53 GMT
Excellent!!!!
Did it work?
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 19, 2020 12:47:17 GMT
Super! Which car is it? A6? And the most important: does the Parking Assist Plus work properly?
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 19, 2020 14:23:47 GMT
Excellent!!!! Did it work? Not yet. I have some static errors from the steering assist controller (44), and the Parking Assist icon is grayed out, so I can't search for a parking place. When I press the button, I get a message on the instrument panel advising to select a parking place first. So, work in progress... Address 44: Steering Assist Labels: None Control Module Part Number: 4N0 909 144 D HW: 4N0 909 144 A Component and/or Version: EPS_MLBEVO2BS H21 0504 Software Coding: B4152301010003 Work Shop Code: WSC 02391 785 00200 ASAM Dataset: EV_EPSVWBSAU426 009015 (AU58) ROD: EV_EPSVWBSAU426_009.rod VCID: 312A1C3760AD420EAC-8064 3160065 - Databus U1121 00 [009] - Missing Message [COMI_TIMEOUT_PLA01] Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 6 Fault Frequency: 1 Reset counter: 50 Mileage: 19256 km Date: 2020.08.17 Time: 19:30:51 FreezeFrame_mw_120C_Timeout-Engine speed: 0.00 /min FreezeFrame_mw_120C_Timeout-System status: 0 FreezeFrame_mw_120C_Timeout-Supply voltage: Terminal 30: 12.18 V FreezeFrame_mw_120C_Timeout-Terminal 15 status measured: On FreezeFrame_mw_120C_Timeout-Engine steering torque sensor: average value: 0.00 Nm FreezeFrame_mw_120C_Timeout-Terminal 15 resulting: On FreezeFrame_mw_120C_Timeout-Terminal 15 status signal: On FreezeFrame_mw_120C_Timeout-Steering pinion angle: offset corrected: 20.26 ° FreezeFrame_mw_120C_Timeout-ARA_signal_red_cyclic: 00 FreezeFrame_mw_120C_Timeout-PLA_signal_red_cyclic: 00 FreezeFrame_mw_120C_Timeout-SCU state: System OK FreezeFrame_mw_120C_Timeout-Steering_angle_sender_status: System OK |
|
|
|
Post by tempos84 on Aug 19, 2020 15:18:23 GMT
Good job rockl! Are you sure that additional wiring is not necessary when changing to >>P button?
|
|
