Post by hobo on Mar 9, 2020 1:44:47 GMT
So I found these instructions below from these forums that were posted a couple years ago. I’ve done several more long coding than what I’m talking about here. But these few have been intermittent at best. This is the second VW I’ve coded (first being my ‘17 Alltrack). And didn’t have any issues
Staging or “needle sweep” only works about 50% of the time.
A/C Recirculation Memory - same as staging. Only works about 50% of the time.
Activate wireless comfort opening/closing- this one works only for the lock/roll up on the windows. Has not worked with unlock/roll down.
Anyone else run into intermittent results like this??
Below are the coding steps I used.
Activate wireless comfort opening/closing (open/close windows using key fob/Kessy)
1/ Select Control Unit: 09 Central Electrics
2/ Select Adaptations
3/ Select ZV Komfort
4/ Change "Funk Komfort schliessen" from "not active" to "active"
5/ Change "Funk Komfort oeffnen" from "not active" to "active"
A/C Recirculation Memory
This change remembers your last recirculation setting. The default setting remembers your setting based on a timer after ignition cycle (ex: 15-20 mins, not sure on what the actual time is).
Steps:
1/ Select Air Conditioning 08
2/ Select Long Coding
3/ Hit the coding icon at the top right kind of looks like this: [0]1
4/ Dismiss warning
5/ Select Byte 4 >> Current value: 20
6/ Uncheck Bit 5
7/ Check Bit 4 >> New value should change to: 10
8/ Save value
>>>Setting Options for Bit 4-5<<<
00 Recirculation Air Settings (after Ignition Cycle) NOT stored
10 Recirculation Air Settings (after Ignition Cycle) stored
20 Recirculation Air Settings (after Ignition Cycle) Timer based (Default setting)
--------------------------------
Staging - This is the needle sweep when you first turn the ignition on
1/ Select Control unit: 17 Dash Board
2/ Select Long coding
3/ Select Staging
4/ Change value from No to Yes
Appreciate any input and advice from the senior OBD11 users!!!
Staging or “needle sweep” only works about 50% of the time.
A/C Recirculation Memory - same as staging. Only works about 50% of the time.
Activate wireless comfort opening/closing- this one works only for the lock/roll up on the windows. Has not worked with unlock/roll down.
Anyone else run into intermittent results like this??
Below are the coding steps I used.
Activate wireless comfort opening/closing (open/close windows using key fob/Kessy)
1/ Select Control Unit: 09 Central Electrics
2/ Select Adaptations
3/ Select ZV Komfort
4/ Change "Funk Komfort schliessen" from "not active" to "active"
5/ Change "Funk Komfort oeffnen" from "not active" to "active"
A/C Recirculation Memory
This change remembers your last recirculation setting. The default setting remembers your setting based on a timer after ignition cycle (ex: 15-20 mins, not sure on what the actual time is).
Steps:
1/ Select Air Conditioning 08
2/ Select Long Coding
3/ Hit the coding icon at the top right kind of looks like this: [0]1
4/ Dismiss warning
5/ Select Byte 4 >> Current value: 20
6/ Uncheck Bit 5
7/ Check Bit 4 >> New value should change to: 10
8/ Save value
>>>Setting Options for Bit 4-5<<<
00 Recirculation Air Settings (after Ignition Cycle) NOT stored
10 Recirculation Air Settings (after Ignition Cycle) stored
20 Recirculation Air Settings (after Ignition Cycle) Timer based (Default setting)
--------------------------------
Staging - This is the needle sweep when you first turn the ignition on
1/ Select Control unit: 17 Dash Board
2/ Select Long coding
3/ Select Staging
4/ Change value from No to Yes
Appreciate any input and advice from the senior OBD11 users!!!