bert
New Member
Posts: 27
|
Post by bert on Feb 21, 2020 11:35:36 GMT
Hallo heb in mijn golf facelift een camera ingebouwd moet hem alleen nog aan de 12v kabel aansluiten. Maar voor ik dat doe , zou ik graag willen weten waar in de obdeleven app ik kan vinden waar ik hem moet aanmelden bv in welke module
nu zie ik nog geen plaatje of iets anders in de app
Hey
have built in a camera in my golf facelift
only need to connect it to the 12v cable.
But before I do that, I would like to know where in the obdeleven app I can find where to register it
eg in which module
now I don't see a picture or anything else in the app
|
|
|
|
Post by vwjap on Feb 21, 2020 13:01:18 GMT
You don’t say if highline or lowline
Low line
5f module (infotainment)
Long coding
Byte 19
Tick bit 4 (Rear view camera)
|
|
bert
New Member
Posts: 27
|
Post by bert on Feb 21, 2020 16:53:14 GMT
thanks i found this.
but what is the difference between low line and hardline.
I have a camera with series no 5G0827469
|
|
bert
New Member
Posts: 27
|
Post by bert on Feb 21, 2020 17:02:57 GMT
thanks i found this. but what is the difference between low line and hardline. I have a camera with series no 5G0827469I also have to change camera type in module 76  |
|
|
|
Post by vwjap on Feb 21, 2020 18:13:26 GMT
Ok lowline with static lines
So yes byte 19 bit 4
And what you said about 76 (park assist module)
|
|
|
|
Post by vwjap on Feb 21, 2020 18:16:19 GMT
Ok I cut and paste this from many of the previous times I’ve posted so you can see the differences Highline reverse camera, as coding to get all the options is different from lowline with less options Lowline  Highline (notice the buttons on right hand side to change camera angles/parking space)  Make sure 5F-long coding-byte19-bit4 is set to not active Go into 5F adaptions Car_Function_List_BAP_Gen2: VPS_0x0B: activated VPS_0x0B_msg_bus: Comfort data bus Then depending on what buttons you have missing go into 6c-long coding correspondence_HMI_RV_mode_1 correspondence_HMI_RV_mode_2 correspondence_HMI_RV_mode_3 correspondence_HMI_RV_mode_5 4 and 6 give you function not available |
|
|
|
Post by thejoker1031 on Feb 24, 2020 1:55:57 GMT
Ok I cut and paste this from many of the previous times I’ve posted so you can see the differences Highline reverse camera, as coding to get all the options is different from lowline with less options Lowline Highline (notice the buttons on right hand side to change camera angles/parking space) Make sure 5F-long coding-byte19-bit4 is set to not active Go into 5F adaptions Car_Function_List_BAP_Gen2: VPS_0x0B: activated VPS_0x0B_msg_bus: Comfort data bus Then depending on what buttons you have missing go into 6c-long coding correspondence_HMI_RV_mode_1 correspondence_HMI_RV_mode_2 correspondence_HMI_RV_mode_3 correspondence_HMI_RV_mode_5 4 and 6 give you function not available |
|
|
|
Post by thejoker1031 on Feb 24, 2020 2:02:59 GMT
Hey everyone. I am sorry to bother you guys, but I need some help here. I am new to the obdeleven and coding. I just bought a 2015 gti/MK7. It did not have a back up camera so I found one on ebay and got the wiring kit from a company in Germany. It's the same one I have seen on this forum. I installed it all,but when I put the car in reverse It flips up, but I get nothing on my screen. I have checked and my model radio is not on the no list for it. I heard you have to code your car in the end of the installation, but that is where I am stuck. How can I code it using the obd 11 pro? If someone knows how and could show me a step by step tutorial that would be awesome. I have no idea where to start you know. Thank you in advance for your help. Stay blessed and safe travels to all.
|
|
bert
New Member
Posts: 27
|
Post by bert on Mar 2, 2020 17:09:26 GMT
thanks everyone for thinking along Camera has been mounted, and works perfectly Maybe want to set it again on highline, but don't know if that makes a big difference
iedereen bedankt voor het meedenken
Camera is inmiddels gemonteerd , en werkt perfect
Wil misschien hem nog eens op highline instellen, maar weet niet of dat veel verschil maakt
|
|
|
|
Post by Carolco on Mar 4, 2020 20:25:42 GMT
What camera installed ?
|
|
bert
New Member
Posts: 27
|
Post by bert on Mar 5, 2020 17:01:28 GMT
|
|
valk
Full Member
Posts: 112
|
Post by valk on Mar 5, 2020 17:08:29 GMT
Bert, je kunt helaas de camera niet anders instellen. Het is of een low-line camera of een highline camera. De ‘luxe’ meedraaiende lijnen zit in de highline camera en niet in de software.
Er valt dus helaas niets aan te passen, of je moet een andere camera monteren.
Groet,
Valk
|
|
bert
New Member
Posts: 27
|
Post by bert on Mar 9, 2020 17:18:43 GMT
hallo Valk
Dat is teminste duidelijk. Bij de aanschaf van de camera kwam ik nergens eigenlijk tegen wat het was'. Nergens stond bij of het een low of een high camera betrof . En ik dacht dat er maar 1 soort was. Dus helaas Maar deze werkt ook perfect dus eigenlijk niets te klagen. maar hartelijk dank voor de uitleg.
mvg Bert
|
|
tenko
New Member
Posts: 4
|
Post by tenko on Apr 29, 2020 17:53:12 GMT
I have fitted one the new oem rear camera high line to my 2016 mk 7 golf gti and I followed all the instructions bap-gen-vps-0x0b activate and bap-gen-vps-0x0b msg-bus terminal 15 .parking assistance activate16byte2 bit4,gateway19 activate 6c reversing camera and my camera is working except it does not show the small optical sensor screen when driving close to an object there is a sound only .the little screen works in reverse can anybody help me .
|
|
|
|
Post by vwjap on Apr 29, 2020 19:37:34 GMT
You’ve activated both high line and lowline, and also do you mean 5f and not gateway? If so de activate the one in 5f and 76
|
|
tenko
New Member
Posts: 4
|
Post by tenko on Apr 30, 2020 10:01:01 GMT
when I coded my camera I used the same code data as yourself except instead of comfort data box I have put in terminal 15 as the suppliers said ,would this cause my problem
Make sure 5F-long coding-byte19-bit4 is set to not active
Go into 5F adaptions
Car_Function_List_BAP_Gen2:
VPS_0x0B:
activated
VPS_0x0B_msg_bus:
Comfort data bus
Then depending on what buttons you have missing go into 6c-long coding
correspondence_HMI_RV_mode_1
correspondence_HMI_RV_mode_2
correspondence_HMI_RV_mode_3
correspondence_HMI_RV_mode_5
4 and 6 give you function not available
|
|
|
|
Post by vwjap on Apr 30, 2020 10:34:09 GMT
Not tried terminal 15 in myself, so can’t tell you if that’s the problem,
|
|
|
|
Post by Carolco on Apr 30, 2020 10:47:47 GMT
 Check this |
|
tenko
New Member
Posts: 4
|
Post by tenko on Apr 30, 2020 13:37:22 GMT
thankyou I will try it,i had the same problem when I had the mib 2 installed and now after a mib2.5 retrofit with the the 9.2 screen I still have the same trouble with the camera not showing the small sensor screen only the sound when approaching an object when I disable the bapvps and code the 5f as a low camera it all works but the the whole idea was getting a camera with the different parking options
|
|
tenko
New Member
Posts: 4
|
Post by tenko on May 5, 2020 17:03:38 GMT
help I was in 5f coding and the adaptions at the bap vrs trying something with my rear camera but I must have coded something or done something to the adaptions because it changed the first three letters of my 5f longcode from 027 to167 and now I have no visual opc just sound and no navigation the rest of the code was the same if anybody has any idea what I have done ,by the way if I manually put the original 027 code in everything works
Coding:02730001000000005111010100880A101F0003D60120040096
Coding:16730001000000005111010100880A101F0003D60120040096 1543 - Control Module Incorrectly Coded
U1014 00 [008] - -
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 4
Fault Frequency: 1
Reset counter: 244
Mileage: 26221 km
Date: 2020.04.29
Time: 14:40:00
Voltage terminal 30: 14.5 V
Byte_Coding_Condition-byte_0_condition: ERROR
Byte_Coding_Condition-byte_1_condition: OK
Byte_Coding_Condition-byte_10_condition: ERROR
Byte_Coding_Condition-byte_11_condition: ERROR
Byte_Coding_Condition-byte_12_condition: ERROR
Byte_Coding_Condition-byte_13_condition: ERROR
Byte_Coding_Condition-byte_14_condition: ERROR
Byte_Coding_Condition-byte_15_condition: ERROR
Byte_Coding_Condition-byte_16_condition: ERROR
Byte_Coding_Condition-byte_17_condition: ERROR
Byte_Coding_Condition-byte_18_condition: ERROR
Byte_Coding_Condition-byte_19_condition: ERROR
Byte_Coding_Condition-byte_2_condition: OK
Byte_Coding_Condition-byte_20_condition: ERROR
Byte_Coding_Condition-byte_21_condition: ERROR
Byte_Coding_Condition-byte_22_condition: ERROR
Byte_Coding_Condition-byte_23_condition: ERROR
Byte_Coding_Condition-byte_24_condition: ERROR
Byte_Coding_Condition-byte_25_condition: ERROR
Byte_Coding_Condition-byte_26_condition: ERROR
Byte_Coding_Condition-byte_27_condition: ERROR
Byte_Coding_Condition-byte_3_condition: OK
Byte_Coding_Condition-byte_4_condition: OK
Byte_Coding_Condition-byte_5_condition: OK
Byte_Coding_Condition-byte_6_condition: OK
Byte_Coding_Condition-byte_7_condition: OK
Byte_Coding_Condition-byte_8_condition: OK
Byte_Coding_Condition-byte_9_condition: OK
|
|
|
|
Post by vwjap on May 5, 2020 17:45:25 GMT
Not 100 but I think 02 is the brand vw, 16 would be another brand of car (seat, Skoda, Bentley, Lamborghini etc)
Long coding goes in pairs of numbers so it wouldn’t be 027
Also maybe you telling it in the gateway you have a high camera and one of two things are happening, either you haven’t got a highline or as in a lot of cases it needs coding as most new highline cameras the long coding is 00 and need a vw dealer to reprogram in Odis
What’s your long coding of module 6c?
|
|
