matt
Junior Member
Posts: 68
|
Post by matt on Jul 10, 2020 22:00:14 GMT
Actually reached out to them about this and was told its not working if you have the 360 cameras, they told me to check back in 2 months for an update. |
|
|
|
Post by andreask on Jul 10, 2020 22:57:05 GMT
OK, I have the answer from the previous Audi master tech. He mentioned we have to add the AI button to active the park assist since the control unit requires the signal from the button. The good news is it is not hard to add that button and he also helped the customer to enable this function before. Here is the part number: 4N9 959 673G View AttachmentView AttachmentAgree, good job digging! Did he if this was for the intelligent or autonomously parkiing? Ref the q3 video I suppose that just builds our case that the park assist plus (assisted steering) should work with 360 cameras, and without AI button. Right? |
|
|
|
Post by harryb on Jul 13, 2020 10:09:33 GMT
Audi Q3 is built on a completelly different platform MQB, so it cannot be referenced in this case as a direct comparison.
|
|
|
|
Post by andreask on Jul 14, 2020 23:29:04 GMT
Audi Q3 is built on a completelly different platform MQB, so it cannot be referenced in this case as a direct comparison. You are right - not directly comparable by platform/environment perspective, but to me the platform is just a different interface/environment to the much of the similar/same functions (and new ones of course), which most probably have the same logic/code behind it.. I’m assuming, or rather hoping, they don’t reinvent the wheel for every new model since 2012 when it comes to park assisted steering. |
|
mat
Closed beta tester
S3 Vorsprung 8Y 2023
Posts: 114 
|
Post by mat on Jul 21, 2020 11:59:04 GMT
If (like me) you got errors on modules 01 and A5. (static errors complaining that the front driver's assist can't be found), then you need to completely power off the car - make sure you've backed out any changes from this thread before hand.
Remove the 12V battery negative cable (thick black cable - it's in the rear right hand side of the trunk, behind a panel that unclips) for 5 minutes, and re-connect. Then clear faults.
On the A7, it's really difficult to get to the negative post of the battery, so I just followed the battery cable where it meets the chassis (only about 10 cm away), and undid it there - make sure you've got at least 1 door open. Also, you might find there is a monitoring/sensor cable on the battery negative post - once you've removed the main cable, I also removed this (it's a 2 wire connector), the re-plugged this back in before re-connecting the main cable on the chassis. (I think this is the battery condition/charge sensor).
Once everything was re-connected, there were lots of faults from lots of different modules, I went in one by one and cleared them. The only one that needed some work was the front driver's door module, as it lost the basic settings for the window. Just fully lower and raise the window a couple of times, and it goes away.
|
|
|
|
Post by andreask on Jul 22, 2020 13:16:48 GMT
I’ve also seen other cars with the park assist module.. probably there is a whole module that we are missing, even though one would think we’ve already got what is necessary. I even experienced auto braking due to some cyclists when backing out of a parking lot, even before the coding of Maneuver assist and the brake module. Maybe should have tried the MA without coding the brakes. |
|
jd
New Member
Posts: 32
|
Post by jd on Jul 25, 2020 2:21:00 GMT
OK, I have the answer from the previous Audi master tech. He mentioned we have to add the AI button to active the park assist since the control unit requires the signal from the button. The good news is it is not hard to add that button and he also helped the customer to enable this function before. Here is the part number: 4N9 959 673G I posted this in the A6 area, but thought that I would put it here. I called AudiUSA parts today. They have a global catalog that includes any part from any country. Part 4N9 959 674G was discontinued in March of this year. No replacement is listed by Audi. There is a part 4N0 959 673J, but it does not say it replaces the G model, but all the specs are the same for both. The J model just became available. The parts guy emailed directly to Audi in Germany and was told that part number 4N0 959 673J just became available but it is not allowed to be sold in the USA. They didn't tell him why, but it is available only in Germany. The parts guy that I spoke to said that he was not allowed to buy one but they are available now in Germany. He said that he has seen this before and has had customers who emailed or called German Audi dealers, made a purchase and had it shipped to them in the USA. |
|
|
|
Post by Park pilot on Jul 30, 2020 3:55:44 GMT
How can I make a switch button on the bottom screen of the MMI that turns off the Lane Assist ?
|
|
|
|
Post by karlis on Jul 31, 2020 6:33:22 GMT
Module: A5 Driver Assistance
LongCoding:
Value: ALDW_handling:
Old: fas_key
New: car_menue
|
|
|
|
Post by Park pilot on Jul 31, 2020 10:13:21 GMT
Thank you. I respect you. I have one more question. Is RS tail lamp animation coding possible?
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jul 31, 2020 16:45:34 GMT
Module: A5 Driver Assistance LongCoding: Value: ALDW_handling: Old: fas_key New: car_menue Thanks for info. I was trying this in my Q8. Unfortunately doesn't work. Every time it's coming back on fas_key. Do you have an idea why? |
|
mat
Closed beta tester
S3 Vorsprung 8Y 2023
Posts: 114
|
Post by mat on Jul 31, 2020 17:12:36 GMT
retom - is your bonnet open?
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jul 31, 2020 22:24:50 GMT
No, do you think that it might be a reason of rejected coding? I did some codings before with closed bonnet and it was approved.
PS. Is the MMI reboot needed? I did it.
Short update. Open bonnet solved the problem. Thanks!
But I have lost now this function in the button of indicator stalk. One or another? No chance to have it on MMI and in the indicator stalk button? Or at least, as it was in my previous Q7, to have this function saved by the car and not enabled again after every restart of the engine?
|
|
jd
New Member
Posts: 32
|
Post by jd on Aug 1, 2020 17:37:29 GMT
I’m sure you already checked, but is it possible that that indicator button becomes the parking button?
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 13, 2020 16:57:42 GMT
The friend of mine shared with me the link to Audi SSP 668. This is for A8 but A7,A6,Q7FL and Q8 often share the same systems and control units. According to the enclosed information it seems that the problem is in control unit, not in coding and Park Assists can not be installed with 360 cameras if the car has unit "C" or higher. Attachments:
|
|
|
|
Post by tempos84 on Aug 14, 2020 13:41:48 GMT
You are right. Park assist couldn't be installed with 360 cameras together probably. But Intelligent Parking Assistant could be installed adding AI or >>P button and appropriate coding. Check my last message at the same topic at A6 threads.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 14, 2020 20:17:20 GMT
This i a great news! It means that Park Assistant Plus is doable in our cars. But still looking for the right coding.
|
|
|
|
Post by mossox on Oct 7, 2020 14:56:31 GMT
Is it working?
Provided, the >> P button is installed and coding was made according to the latest post in the A6 forum.
There is transmission malfunction.
Guess, there must made some adaption to the 02.
Can anybody provide the coding of 02 with IPA installed?
Mine is "000001".
I found some modules coded to "100000".
Might that be the missing coding??
Adresse 02: Getriebe (J217) Labeldatei:| 0CJ-927-156.clb
Teilenummer SW: 4K0 927 153 AB HW: 0HK 927 156 B
Bauteil: 0CK 20TDI RdW H01 0005
Revision: --H01--- Seriennummer: 0000002504
Codierung: 000001
Betriebsnr.: WSC 02664 785 00200
ASAM Datensatz: EV_TCMDL382021 002031
ROD: EV_TCMDL382021_AU58.rod
VCID: 6D86311F9D1D7BD388C-8038
|
|
hoya
New Member
Posts: 1
|
Post by hoya on Oct 10, 2020 15:07:48 GMT
If (like me) you got errors on modules 01 and A5. (static errors complaining that the front driver's assist can't be found), then you need to completely power off the car - make sure you've backed out any changes from this thread before hand. Remove the 12V battery negative cable (thick black cable - it's in the rear right hand side of the trunk, behind a panel that unclips) for 5 minutes, and re-connect. Then clear faults. On the A7, it's really difficult to get to the negative post of the battery, so I just followed the battery cable where it meets the chassis (only about 10 cm away), and undid it there - make sure you've got at least 1 door open. Also, you might find there is a monitoring/sensor cable on the battery negative post - once you've removed the main cable, I also removed this (it's a 2 wire connector), the re-plugged this back in before re-connecting the main cable on the chassis. (I think this is the battery condition/charge sensor). Once everything was re-connected, there were lots of faults from lots of different modules, I went in one by one and cleared them. The only one that needed some work was the front driver's door module, as it lost the basic settings for the window. Just fully lower and raise the window a couple of times, and it goes away. I'm so sorry. It's too difficult. Can you show me the picture? |
|
|
|
Post by mikele74 on Jul 13, 2021 9:26:52 GMT
Here you go - sorry it's an image - couldn't get a table to format properly in this forum. 
Raw text: Module Type Setting Old New 5F Adaptation Dashboard display configuration -> ability_switch_nav_maps Off On 5F Adaptation Vehicle Configuration -> VZAPro Off On 5F Adaptation Vehicle Configuration -> online_street_view Off On 5F Adaptation Vehicle Configuration -> OPS_display_in_dash_board_display_unit Off On 09 Long Coding PLA_Parking_space_Selection hardkey softkey 09 Adaptation Show parking space Not activated Activated A5 Adaptation Visual display for park assist OPS display With OPS 360 All coding above didn’t actually do anything until 17 Long Coding Intelligent Park Assist ? On 44 Long Coding Parallel Parking Assistance ? On A5 Long Coding ipa_intelligent_parking_assist Not activated activated A5 Long Coding FW_interface_parking_button Hard key Soft key A5 Long Coding IPA Curb Lifter Not activated activated A5 Long Coding FW_PLA_BCM Not activated activated A5 Adaptation Parking assistance fade in Not activated activated 09 Long Coding Pla activaton Hard key Soft key This one caused issues.... 19 Adaptation Installed specified list -> Park Assistance Not installed Installedcan it work with my Audi Q3 spb 2020? |
|
|
|
Post by mikele74 on Jul 13, 2021 9:37:12 GMT
can it work with my Audi Q3 spb 2020?
|
|
|
|
Post by bigfoot0387 on Aug 25, 2022 15:58:18 GMT
Can anyone clarify if you actually need the 360 camera to have park assist? TIA
|
|
|
|
Post by giggioaudi on Nov 5, 2022 20:40:30 GMT
Hi guys, I retroffitted Top View System complete on my Audi A6 c8. Work Perfectly!
I want, Now, activate the ipa (i mounted the keys in console). The coding is complete?
|
|
phmb
New Member
Prince of Diesel
Posts: 3
|
Post by phmb on Dec 25, 2022 20:54:27 GMT
Is there anyone who managed to determine the correct coding with the 360 camera system?
|
|
|
|
Post by bhanvadia on Jan 21, 2023 15:07:05 GMT
I am gonna get scan of Car with Park Pilot (One with P>> Button) and 360 cam, will compare long codings with my car and find exact changes.
|
|
phmb
New Member
Prince of Diesel
Posts: 3
|
Post by phmb on Feb 10, 2023 1:00:58 GMT
Any update?
|
|
|
|
Post by bhanvadia on Feb 10, 2023 9:42:49 GMT
|
|
