T-Roc Coding and Adaptions

Is there any way to code traffic jam assist, emergency assist and video in motion on t-roc please

Scandinavian DRL
Select Control Unit 09 (Central Electrics)
Security access
Access Code 31347
Adaptations
Select: Aussenlicht_Front
Select: Tagfahrlicht-Dauerfahrlicht aktiviert zusaetzlich Standlicht
Value: Active (orginal inactive)

Light Assist and option in the menu
NB.: for T-Roc with LED package
Go to Module 09 (Electronic switchboard)
Click on Adaptation
Search Fernlicht_assistent
Enter Erweiterte_Fernlichtsteuerung . Switch to AFS, FLA, Fernlicht ueber AFS.
Enter Menuesteuerung Fernlichtassistent. Switch to Available.
Press the Validate button. The code is 31347.
lr to Module A5 (front sensors)
Click on Extended coding
Press the button on the top right that shows '0' and '1' to see it Bytes mode; Each Byte has 8 bits (from 0 to 7 included)
Press the right arrow until you reach Byte 21
Within Byte 21 activate bit 5-7 and do not modify the others. (Read note below)
Press the Validate button
The modification should work.
Note: In step 11 the bit appears like "5-7" and it is only one box, you do not have to modify the others only that one.
For halogen lights the modification may be different, it is not tested.
It only works when we have the light control in the 'Auto' position.
It will remain as it was left when the contact is removed.
Additional modification: If we want the contact to be deactivated, we must include the next step between point 5 and 6, we include. Enter Fernlichtassistent reset. Switch to Active.
How it works: Activated with the light lever. The light assistant works through the camera and front light sensor and switches between long or short light automatically depending on the lighting conditions of the road and if there is traffic in front. Without the modification when we want to put the long light we must push the lever forward and to turn off the long light we pull the lever towards us. After the modification when we push once activates the Light Assist and the corresponding icon appears in the instrument panel, and when we push a second time the permanent long light is activated, but if we push a third we activate the Light Assist again and successively it will be switching between the two modes.
So to deactivate it? There are two options, one is to push the light lever once to exit the Light Assist and activate the permanent long light and then pull the lever towards us and at that moment the long light will also be deactivated, returning to normal. The other option is to deactivate the new option that appears in the lighting settings from the menu.

traffic sign recognition

A5-Front Sensors]
Click on Extended coding
Press the button on the top right that shows a '0' and '1' to see it Bytes mode; Each Byte has 8 bits (from 0 to 7 included)
Press the right arrow down until you reach Byte 16
Inside Byte 16 activate bit 4 and do not modify the rest
Press the Validate button
Exit Module A5 and enter Module 5F
Click on Adaptation
Search for Car_Function_Adaptations_Gen2
Enter menu_display_road_sign_identification and change to On
Enter menu_display_road_sign_identification_over_threshold_high and change to On
Press the Validate button
Go back to Adaptation and look for Car_Function_List_BAP_Gen2
Enter traffic_sign_recognition_0x21 and change to On
Enter traffic_sign_recognition_0x21_msg_bus and change to ' Data Bus Infotainment'
Press the Validate button
Exit Module 5F and enter Module 17
Click on Extended Coding
Press the button on the top right that shows a '0' and '1' to see it Bytes mode; Each Byte has 8 bits (from 0 to 7 included)
Down, press the right arrow until you reach Byte 5
Inside Byte 5 activate bit 2 and do not modify the rest
Press the Validate button
Restart the Infotainment by pressing and holding the power button between 10s to 15s and release.
It should work already. In the settings of the driving assistants, the option 'Signal recognition' should appear and the speed signals appear in the frame.
Note: This extra is associated with the GPS, so those without a GPS will see a message on the infotainment when entering to see ' the state of the car' which indicates that signal recognition is limited. This warning will also appear for a few seconds in the instrument cluster to start the march. This message is only informative and does not produce any problem, error or failure. The recognition of signals will work normally but limited without the information that the navigator could provide.

Hello

I have already activated the codes , but unfortunately nothing happened to my car ,

I also changed at logcoding
09 centra electrics
subsystems
RLHS
LONG CODING
byte 00
bit 2  not active = new active

nothing happened 

I checked - for my t roc it doesn't work too.
which year of production do you have?
I think they changed rain sensor from 2019 and this coding is not working anymore...

I don't know what type of sensor i have, I'm driving a model 2019 T Roc

5Q0955547B that's mine

just tested my TRoc, and sadly it's not working properly, however it is visible in my menu.

I'll try, thanks for thinking along.

It doesn't work 😕

Hello, I can't modify bit 7 on byte 21. (5 and 6 no problem) says function not availble. 


I have led lights and lane assist on my Troc 2019. 

Hello how to deactivated start/stop function please help...