|
|
Post by bendert96 on May 3, 2019 21:16:34 GMT
Hello,
I'm pretty new to this all. I've accomplished to activate us lights, and after that change the light brightness.
But now I want to change my h7 led lights brightness. Because one is a bit brighter than the other one.
And can I activate leaving home / coming home without light sensor?
|
|
|
|
Post by dv52 (Australia) on May 3, 2019 23:26:49 GMT
^^^H7 question: What is your current value for the adaptation channel Leuchte6ABL LC5-Lasttyp 6 in the Central electrics module?
Leaving/coming home question: you can activate CH, but not LH if there is no light sensor. To activate CH - change the adaptation channels in the highlighted section of the screen below on the Central electrics module:  If you have a newer model mk7 (i.e. after MY16), search for Außenlicht_uebergreifend (instead of "comfort illumination" in my picture) To activate CH after making the changes, make sure that CH is enabled in the MENU screen (CAR>setup>lights>coming home=10 seconds) -then operate the high-beam flash stalk before opening the driver door to exit the car. The CH lights will stay illuminated for 10 seconds after the last door is closed (including the rear-hatch) Don |
|
|
|
Post by eddie99 on May 4, 2019 10:09:25 GMT
Hello, But now I want to change my h7 led lights brightness. Because one is a bit brighter than the other one. Hi were the h7 leds factory fitted or did you fit them yourself ?
Could you tell me the make of h7 led bulb ? I presume the h7 leds are for your low beams ?
|
|
|
|
Post by bendert96 on May 4, 2019 23:33:05 GMT
^^^H7 question: What is your current value for the adaptation channel Leuchte6ABL LC5-Lasttyp 6 in the Central electrics module?
Leaving/coming home question: you can activate CH, but not LH if there is no light sensor. To activate CH - change the adaptation channels in the highlighted section of the screen below on the Central electrics module: If you have a newer model mk7 (i.e. after MY16), search for Außenlicht_uebergreifend (instead of "comfort illumination" in my picture) To activate CH after making the changes, make sure that CH is enabled in the MENU screen (CAR>setup>lights>coming home=10 seconds) -then operate the high-beam flash stalk before opening the driver door to exit the car. The CH lights will stay illuminated for 10 seconds after the last door is closed (including the rear-hatch) Don Thanks will try it! And check the value tomorrow |
|
|
|
Post by bendert96 on May 4, 2019 23:35:49 GMT
|
|
|
|
Post by bendert96 on May 4, 2019 23:37:07 GMT
Dv52,
Do you know of teardrop wiping is an option for a mk7 and how I'm activating this?
Couldn't find it...
|
|
|
|
Post by bendert96 on May 5, 2019 9:47:02 GMT
Here the values Attachments:
|
|
|
|
Post by dv52 (Australia) on May 5, 2019 12:19:39 GMT
hmm........ the illumination level for the low-beam lamps is set by the value in Leuchte6ABL LC5-Dimmwert AB 6 (left-side) and Leuchte7ABL RB1-Dimmwert AB 7 (right-side) channels . You could also try changing Leuchte6ABL LC5-Lasttyp 6 and Leuchte7ABL RB1-Lasttyp 7 to 5 LED Abblendlicht. Don |
|
|
|
Post by dv52 (Australia) on May 5, 2019 12:29:33 GMT
Dv52, Do you know of teardrop wiping is an option for a mk7 and how I'm activating this? Couldn't find it... If you search the hex09 module for the term Windshield wiper, you should find a channel called Traenenwischen Front Status (Traenenwischen=Tears-wipe) which is factory set to not active - but changing this channel to active won't work. So I don't know - sorry
Don
PS: You could also check that Byte 0, Bit 3 (adaptive Post/Tear wiping active) is set in the WWWS module (which is a subsystem in the hex09 module)
|
|
|
|
Post by bendert96 on May 5, 2019 13:48:52 GMT
Thanks your the best! If solved the problem with Dimmwert AB 6.
Do you also know how I can let all lights work at the same time? Low beam and city lights
I've tried to add a new lichtfunction at c6 but without success.
|
|
|
|
Post by dv52 (Australia) on May 5, 2019 21:03:35 GMT
OK - what "lichtfunction at C6" did you add and what country are you from?
|
|
|
|
Post by bendert96 on May 5, 2019 21:22:03 GMT
OK - what "lichtfunction at C6" did you add and what country are you from? I've tried a couple fernlicht,standlicht I'm from the Netherlands |
|
|
|
Post by dv52 (Australia) on May 5, 2019 22:32:58 GMT
OK - what "lichtfunction at C6" did you add and what country are you from? I've tried a couple fernlicht,standlicht I'm from the Netherlands Did you try this:
Leuchte6ABL LC5 - Lichtfunktion C 6 > Fernlicht links
- Dimmwert CD 6 > 100
Leuchte7ABL RB1 - Lichtfunktion C 7 > Fernlicht rechts
- Dimmwert CD 7 > 100
Don
PS: And if you want low-beams (city-lights?) with high-beam flash too- try this:
|
|
|
|
Post by bendert96 on May 6, 2019 5:39:19 GMT
I've tried a couple fernlicht,standlicht I'm from the Netherlands Did you try this:
Leuchte6ABL LC5 - Lichtfunktion C 6 > Fernlicht links
- Dimmwert CD 6 > 100
Leuchte7ABL RB1 - Lichtfunktion C 7 > Fernlicht rechts
- Dimmwert CD 7 > 100
Don
PS: And if you want low-beams (city-lights?) with high-beam flash too- try this:
Thanks I've tried that but with no success. And city lights is what is called here. It is Drl, ssame light as high beam |
|
|
|
Post by bendert96 on May 6, 2019 6:16:01 GMT
And can I adjust the height/position of one headlight?
|
|
valk
Full Member
Posts: 112
|
Post by valk on May 6, 2019 7:44:09 GMT
OK - what "lichtfunction at C6" did you add and what country are you from? I've tried a couple fernlicht,standlicht I'm from the Netherlands Waar woon je? Misschien kan ik met je meekijken en komen we er samen uit. |
|
|
|
Post by bendert96 on May 6, 2019 10:45:29 GMT
I've tried a couple fernlicht,standlicht I'm from the Netherlands Waar woon je? Misschien kan ik met je meekijken en komen we er samen uit. In Winschoten, vermoedelijk niet in de buurt |
|
valk
Full Member
Posts: 112
|
Post by valk on May 6, 2019 11:00:43 GMT
Waar woon je? Misschien kan ik met je meekijken en komen we er samen uit. In Winschoten, vermoedelijk niet in de buurt Toch wel, ik in Groningen  |
|
|
|
Post by bendert96 on May 6, 2019 13:39:28 GMT
In Winschoten, vermoedelijk niet in de buurt Toch wel, ik in Groningen Pm |
|
|
|
Post by mikeyx on Feb 3, 2022 22:00:26 GMT
My car is Golf 7 (2014) with halogen headlights.
Is it possible to increase the light intensity using OBD11?
|
|
|
|
Post by dv52 (Australia) on Feb 3, 2022 23:17:12 GMT
Mikey: Hi. Not sure which lamp in your halogen headlights you want to make brighter - but in general, the illumination level for lighting functions like low-beam and high-beam are factory set to maximum brightness
Don
|
|
|
|
Post by mikeyx on Feb 4, 2022 5:29:55 GMT
^Thanks for the reply!
Still clutching at straws... I have come across a thread in which it was mentioned that one could deselect 'power saving mode' in central electrics. Any idea what that is all about?
|
|
|
|
Post by dv52 (Australia) on Feb 4, 2022 20:15:27 GMT
no
|
|
