|
|
Post by florian on Mar 21, 2019 21:17:41 GMT
Salut à tous, désolée pour mon anglais, je suis française, je suis sur le point de procéder à une nouvelle mise à niveau, qui consiste à installer la caméra dans le pare-brise avant, afin que la ligne soit assistée et que tout ce qui suit sui, l'opération nécessite changer le pare-brise, que j’ai déjà acheté, alors que j’ai trouvé un pare-brise neuf, (produit VW) qui a 2 fils car il est chauffant, cela pendant nous en France cette option n’existait pas, mais j’aimerais en profiter Pour que cela fonctionne, savez-vous où je peux trouver le faisceau pour le connecter et surtout pour savoir où il se connecte? Merci de votre aide
|
|
|
|
Post by dv52 (Australia) on Mar 22, 2019 0:23:59 GMT
florian: hello again! Here's my cut-down version of the wiring diagram for the heated windshield arrangement (This diagram is taken from a 2014 sports-wagon):  So, I'm not sure how familiar you are with electrical circuits, but it's a fairly simple wiring arrangement. Because of the comparatively high current demand in the heating element in the windscreen, a separate relay is needed to handle the power flow. Controlling the heating element (Z2 in the picture) is then done by energizing the coil of the relay - which requires a much smaller electrical current. As you can see from my diagram, control of the switch ON/OFF facility happens in J519 (this is the control module that OBD11 calls Central Electric @ address hex09). You will need to tell J519 that it needs to control the heated windscreen: this is done by enabling Byte 3, Bit 5 (or you could use the screenshot below). You should also find a bunch of adaptation channels in the control module that are specifically related to the heated windscreen -like these: Window heater-Running time of heated front window
Window heater-Abschalttemperatur fuer Frontscheibenheizung
Window heater-Abschalttemperatur fuer Heckscheibenheizung
Window heater-FSH Automatik
Window heater-Heckscheibenheizung Zeitwert
Window heater-Temperaturabhaengige Einschaltzeit FSH
Window heater-Temperaturabhaengige Einschaltzeit HSH
I suspect that you will need to run the wiring for the relay and also install the relay and the fuse holders. But I suggest that the first task is to check whether pin#26 on the A socket on J519 on your car is actually populated. This will tell you whether your control module can facilitate heated windscreen
If the pin is present on your car, I further suggest that you enable the Byte/Bit and check the operation of pin #26, socket A before going to the effort of installing the other equipment. You can do this by checking (with a multi-meter) that the pin is earthed when the heated windscreen is turned-on.
Don
|
|
|
|
Post by florian on Mar 26, 2019 21:50:48 GMT
Hi"DV52" Thank you again for your help, you understand my request, I thank you for your answers, this for I think I have the amplecement on the BCM given that I changed my new BCM middle against a Highline come d Germany for adding heated seats that works perfectly, for I mean I plugged in as you say, but where to find the beam for that? I search the internet I have no reference or anything else to find the beam and everything I need to buy. You did not answer my second private message.
|
|
|
|
Post by dv52 (Australia) on Mar 27, 2019 0:30:34 GMT
^^^ hmm........ please resend the PM containing "my second private message". I don't have a parts list for the retrofitted windshield heater and I suspect that you won't find it on the net. But just look at my wiring diagram and see what equipment is NOT currently installed on your car. If the windshield heater is not offered in your country, I suspect that you will need to source ALL the components in my wiring diagram. Not sure what you mean by the "beam" (a problem with your English translator - I think). I'm guessing that you are referring to the connection on the BCM - the control module @ address hex09. If so - here is the socket identifiers and pin number layout on the BCM - the actual pin numbers are also physically stamped onto the base of the housing:  So - as per my wiring diagram above, you will need to locate pin number 26 on Socket A. First- make sure that the pin is actually present on the BCM in your car. Second - enable the Byte/Bit in my previous post and turn-on the heated windshield function - make sure that pin number 26 on Socket A is earthed (using a multi-meter) when you turn-on the heater. Only after you have confirmed these steps should you try to source the other pieces of equipment because your BCM might not have the functionality to operate a heated windshield. Don |
|
|
|
Post by florian on Mar 29, 2019 15:00:18 GMT
Hi "DV523 I sent you a private message yesterday for another request, but I see that it does not appear in the messages sent on the forum, so I will write to you here, if you can delete it once that you read it is perfect you answer me privately, I bought a new highline camera never installed, I have a problem I wanted to code the calculator with Odis VCDS or OBD11 but I'm entitled to the mistake you see you know how to help me? Thanks zupimages.net/viewer.php?id=19/13/ttwc.jpgzupimages.net/viewer.php?id=19/13/y13z.jpg |
|
|
|
Post by ofektal8 on Mar 29, 2019 15:40:34 GMT
This is the coding for my camera if you want, but you will have to change the model as it is set to skoda.
04840201E2002017000040
|
|
|
|
Post by florian on Mar 29, 2019 19:08:19 GMT
Hi "ofektal8" thanks for your help the problem is that I can not parametre anything, there is a concern which I do not master, must tell me why I have this error when I want to change the long coding.
|
|
|
|
Post by ofektal8 on Mar 29, 2019 19:40:48 GMT
Hi "ofektal8" thanks for your help the problem is that I can not parametre anything, there is a concern which I do not master, must tell me why I have this error when I want to change the long coding. After looking at my backup from when i installed my camera, I had the exact same faults. Your camera is indeed missing parameters, It can be uploaded Using ODIS or VCP. |
|
|
|
Post by florian on Mar 30, 2019 11:31:15 GMT
Salut "ofektal819" Je possède exactement Odis avec un accès en ligne, mais le problème est que la caméra Highline que j'ai prise provient d'une Passat B8, je possède un golf et, sur notre parcours, il n'y a pas de caméra Highline. Nous devons donc la prendre le passat b8, alors que je n'ai pas la possibilité de le coder car Odis détecte ma voiture, et pour lui ce n'est pas compatible, avec VCP c'est probablement possible mais je n'ai pas de VCP et l'acheter pour une fois n'est pas forcément intéressant, la limite si j'ai le fichier xlms de l'appareil photo, je pourrais le faire avec Odis E
|
|
|
|
Post by ofektal8 on Mar 30, 2019 15:53:37 GMT
Salut "ofektal819" Je possède exactement Odis avec un accès en ligne, mais le problème est que la caméra Highline que j'ai prise provient d'une Passat B8, je possède un golf et, sur notre parcours, il n'y a pas de caméra Highline. Nous devons donc la prendre le passat b8, alors que je n'ai pas la possibilité de le coder car Odis détecte ma voiture, et pour lui ce n'est pas compatible, avec VCP c'est probablement possible mais je n'ai pas de VCP et l'acheter pour une fois n'est pas forcément intéressant, la limite si j'ai le fichier xlms de l'appareil photo, je pourrais le faire avec Odis E Mine is a golf too and was missing parameters so we used VCP To upload Skoda parameters so uploading other cars parameters is fine, ODIS E and VCP are your only options Just upload the correct parameters using the file that matches the Part Number of your camera. VCP Is easier but If you have ODIS E then it will work too. |
|
|
|
Post by florian on Apr 1, 2019 15:44:42 GMT
Hi, precisely, I would like to find the settings for my camera, for Odis E, as I do not have a VCP, while I did not find anything on the internet, my reference is "3G0827469AQ" but I do not find nothing
|
|
|
|
Post by ofektal8 on Apr 2, 2019 11:23:46 GMT
Hi, precisely, I would like to find the settings for my camera, for Odis E, as I do not have a VCP, while I did not find anything on the internet, my reference is "3G0827469AQ" but I do not find nothing You wont find it anywhere online, I thought you had the files but if not then VCP Is the way, try to find a shop that has it or I think ODIS S Can do it using SVM( Not sure but give it a shot) |
|
|
|
Post by florian on Apr 8, 2019 20:51:56 GMT
Hi all, I come back for my camera problem I found a member in France, who owns official VCP, we tried to search my camera with my reference in the available files and we unfortunately found nothing, I believe that I I have to drop this possibility, to go back to my windshield history I have not managed to activate the encodings, maybe because the connections are not yet realized? Or even without hooking up the codings should passed
|
|
|
|
Post by ofektal8 on Apr 9, 2019 6:21:30 GMT
Hi all, I come back for my camera problem I found a member in France, who owns official VCP, we tried to search my camera with my reference in the available files and we unfortunately found nothing, I believe that I I have to drop this possibility, to go back to my windshield history I have not managed to activate the encodings, maybe because the connections are not yet realized? Or even without hooking up the codings should passed If your car is an MQB then the part number you mentioned isnt correct, The one Most MQB Cars use is 5Q0980556B It doesnt matter if you upload Passat Or Skoda parameters to your camera. |
|
|
|
Post by florian on Dec 16, 2019 23:22:17 GMT
Hello everyone, I come back to you with this story of the heated front windshield, I was finally able to get my hands on the OEM harness so I bought and installed it as planned, until then nothing difficult everything is happening in the motor fuse box, so I did it cleanly, only one cable is connected to plug B of the BCM, so I installed all of this, I only coded in module 08 climatronic, saying that the barrier defrosting breeze was installed, the icon appeared on the 5f but as soon as I click on it, it goes out immediately nothing works, I ask for your help for the complete coding, I had an error by saying that my engine control unit was badly coded even though I didn't touch anything on it.
cordially
|
|
|
|
Post by ofektal8 on Dec 17, 2019 9:16:14 GMT
Hello everyone, I come back to you with this story of the heated front windshield, I was finally able to get my hands on the OEM harness so I bought and installed it as planned, until then nothing difficult everything is happening in the motor fuse box, so I did it cleanly, only one cable is connected to plug B of the BCM, so I installed all of this, I only coded in module 08 climatronic, saying that the barrier defrosting breeze was installed, the icon appeared on the 5f but as soon as I click on it, it goes out immediately nothing works, I ask for your help for the complete coding, I had an error by saying that my engine control unit was badly coded even though I didn't touch anything on it. cordially Have you coded it on 09 like Don said,? Also i assume you need to code other modules, like 5f and maybe the engine? As it says module incorrectly coded. |
|
|
|
Post by florian on Dec 17, 2019 20:54:09 GMT
Hi ofektal8 here is what I have in my BCM, it is no longer in long coding since I have a last generation BCM there is no longer long coding   |
|
|
|
Post by ofektal8 on Dec 18, 2019 20:30:59 GMT
Hi ofektal8 here is what I have in my BCM, it is no longer in long coding since I have a last generation BCM there is no longer long coding First thing to do is to set "heizbare_frontscheibe" to installed, it means heated windscreen. |
|
|
|
Post by florian on Dec 19, 2019 12:18:25 GMT
ofektal8 Hi thank you for your answers, is there anything else to add? I tried and actually the windshield finally works, this during I have two more questions, the windshield can activate automatically but what is the action that will allow it to activate automatically? Second question I still have an error since my installation in the engine module saying badly coded calculator, do you know what I should add?
|
|
|
|
Post by ofektal8 on Dec 19, 2019 12:26:17 GMT
ofektal8 Hi thank you for your answers, is there anything else to add? I tried and actually the windshield finally works, this during I have two more questions, the windshield can activate automatically but what is the action that will allow it to activate automatically? Second question I still have an error since my installation in the engine module saying badly coded calculator, do you know what I should add? Hey, I'm not sure if there is anything else to add. This retrofit is rare and I Cant find A lot of info about it. Are you sure that the error in engine module appeared right after installing the windshield? And Here is how to enable auto heating Automatic windscreen heating The windscreen heating switches on automatically if there is a risk of condensation building up on the windscreen or windows. Press the MENU button on the control panel. Press the COG function button in the Infotainment system. Switch automatic windscreen heating on or off by touching the Automatic windscreen heating function button. The automatic windscreen heating is also active when the air conditioning system is switched off. |
|
|
|
Post by sergelhr on Dec 6, 2021 16:05:12 GMT
dv52 (Australia)Onboard supply control unit -J519- Fitting location: Behind dash panel, left 1 - Onboard supply control unit -J519- A - 73-pin connector -T73a- B - 46-pin connector -T46a- C - 73-pin connector -T73b- Connector assignment of onboard supply control unit -J519- T46a/26 46 pins position B from elsawin , a an c 73 pins
|
|
