|
Post by perforin on Feb 28, 2019 21:45:49 GMT
Either my search isn’t working or this hasn’t been touched on yet. Replaced my totaled 2016 GTI with a 2019 and it has a new audible and MFD warning when the driver door is opened while the ENGINE is on. It sounds just like the one when the IGNITION is on and the driver side door is opened. Coding the ignition warning off (17 -> Ignition Active Message; Trigger) didn’t effect the behavior for when the door is opened with the engine running, ie. still beeps. Looked at the adaptations for Module 17 - Dashboard via OBDeleven and didn’t see anything that would obviously change this. Anyone have any ideas or luck with turning this off? 
|
|
2018gti
Full Member
 
2018 GTI Autobahn 6-speed
Posts: 100
|
Post by 2018gti on Mar 7, 2019 2:15:29 GMT
"Attention: Engine is running".... Oh really?? I didn't even know, thanks VW!  That sounds so annoying, I didn't know they added a new message just for that. So your dashboard doesn't have the little picture of the car that shows which door is open?
|
|
|
Post by perforin on Mar 18, 2019 20:25:34 GMT
"Attention: Engine is running".... Oh really?? I didn't even know, thanks VW!  That sounds so annoying, I didn't know they added a new message just for that. So your dashboard doesn't have the little picture of the car that shows which door is open? Nope. My 2016 did, but this 2019 just shows the message with the annoying beep. Any fixes for this?
|
|
|
Post by dv52 (Australia) on Mar 18, 2019 21:20:34 GMT
"Attention: Engine is running".... Oh really?? I didn't even know, thanks VW!  That sounds so annoying, I didn't know they added a new message just for that. So your dashboard doesn't have the little picture of the car that shows which door is open? Nope. My 2016 did, but this 2019 just shows the message with the annoying beep. Any fixes for this? perforin: Hi. My suggestion is a bit of a guess - but try this:
- Go to adaptation part of the control module that OBD11 calls Dashboard (it lives @ address hex17)
- Search for the "parent" name Configuration of displayable contents and hopefully you can select the channel called Display: engine running required
- If my guess is correct, the setting on your car should be yes - if so, change the setting to no (you may be asked to enter a security code - if so, use 47115)
Don
|
|
|
Post by perforin on Apr 11, 2019 4:51:31 GMT
Nope. My 2016 did, but this 2019 just shows the message with the annoying beep. Any fixes for this? perforin: Hi. My suggestion is a bit of a guess - but try this:
- Go to adaptation part of the control module that OBD11 calls Dashboard (it lives @ address hex17)
- Search for the "parent" name Configuration of displayable contents and hopefully you can select the channel called Display: engine running required
- If my guess is correct, the setting on your car should be yes - if so, change the setting to no (you may be asked to enter a security code - if so, use 47115)
Don
I finally got to try this tonight. Unfortunately I could not find that channel in my 2019  Oh well, thanks for chiming in and trying to help! Please let me know if you have any other ideas.
|
|
|
Post by hardguy on Aug 11, 2019 2:50:42 GMT
Same here. No adaptation in 17 for my 2019 GLI either..... there’s gotta be a way, somehow.
|
|
|
Post by yoshimbo on Jan 23, 2020 7:49:33 GMT
I am actually in a very similar situation to you, OP. I had a 2018 GTI, totaled, replaced with a '19. This beep is driving me bonkers too. I've tried both solutions offered here with no luck.
|
|
|
Post by tykrumm on May 4, 2020 2:13:43 GMT
did either of you ever figure out how to disable this chime?
|
|
|
Post by vwjap on May 4, 2020 17:00:49 GMT
Something in long coding you could try
Exit warning from yes to no
|
|
|
Post by tykrumm on May 6, 2020 1:07:54 GMT
i tried 17-Dashboard > Adaptations > Exit Warning No. still no luck. any other ideas?
|
|
13
New Member
Posts: 23
|
Post by 13 on May 6, 2020 16:24:16 GMT
Something in long coding you could try Exit warning from yes to no I saw that the other day and was hoping it would disable the "don't forget your mobile phone" message that pops up when leaving the car. Hadn't had a chance to look into it yet, though.
|
|
|
Post by vwjap on May 6, 2020 18:19:50 GMT
I have a auto, so it doesn’t beep with engine running only in gear, then it says put in p
|
|
|
Post by dmichael97 on Jun 14, 2020 21:13:25 GMT
I used the APP to change the value of Open Door Alarm (with engine running) - initially it was set to "alarm on, drivers door". I changed to "off" the app took 10 points from my account but the alarm still sounds. When I go back to double check the setting, it shows "off". What gives? If there was another procedure to make the setting stick the app does not explain that at all.
The car is 2020 VW GTI SE with keyless entry, start stop button
Thanks
Note: I got the gauge needle sweep activated, I never intended to do that, somehow the open door alarm results in needle sweep ?!?!
|
|
|
Post by guibulle on Jul 3, 2020 10:14:17 GMT
Hi I'm trying to do the same thing on a 2020 Polo GTI and ending to the same result ,i also try to switch "alarm on, drivers door" to "off" and it fail.
Still searching !
|
|
|
Post by lordnikon on Jul 3, 2020 13:15:37 GMT
I used the APP to change the value of Open Door Alarm (with engine running) - initially it was set to "alarm on, drivers door". I changed to "off" the app took 10 points from my account but the alarm still sounds. When I go back to double check the setting, it shows "off". What gives? If there was another procedure to make the setting stick the app does not explain that at all. There is a difference between having the engine running and getting the 'beep' and ignition ON 'beep'. The latter can be disabled but not the former.
|
|
|
Post by dmichael97 on Jul 3, 2020 14:09:05 GMT
I used the APP to change the value of Open Door Alarm (with engine running) - initially it was set to "alarm on, drivers door". I changed to "off" the app took 10 points from my account but the alarm still sounds. When I go back to double check the setting, it shows "off". What gives? If there was another procedure to make the setting stick the app does not explain that at all. There is a difference between having the engine running and getting the 'beep' and ignition ON 'beep'. The latter can be disabled but not the former. My only point was that the app took 10 credits, changed the value to "off" successfully, but the behavior remains the same, no change, so what is the app suppose to accomplish?
|
|
|
Post by lordnikon on Jul 3, 2020 14:29:05 GMT
There is a difference between having the engine running and getting the 'beep' and ignition ON 'beep'. The latter can be disabled but not the former. My only point was that the app took 10 credits, changed the value to "off" successfully, but the behavior remains the same, no change, so what is the app suppose to accomplish? You still don't get it. The app disables the ignition ON beep. It works! however it does NOT disable Engine is running beep.
Ignition ON and Engine ON is not the same.
|
|
|
Post by misterx on Jul 12, 2020 12:13:45 GMT
My only point was that the app took 10 credits, changed the value to "off" successfully, but the behavior remains the same, no change, so what is the app suppose to accomplish? You still don't get it. The app disables the ignition ON beep. It works! however it does NOT disable Engine is running beep.
Ignition ON and Engine ON is not the same.
You are right , sadly. I bought obdeleven expressly to remove this ANNOYING noise.... .and nothing can be done . Why instead , safety belt alarm is quieter? It should be the opposite !!
|
|
|
Post by dmichael97 on Jul 12, 2020 12:23:04 GMT
There has to be a way through long coding, I just haven't found it yet, if anyone stumbles across it, please post it here, I would do the same...
|
|
|
Post by depocomp on Jul 23, 2020 6:58:43 GMT
There has to be a way through long coding, I just haven't found it yet, if anyone stumbles across it, please post it here, I would do the same... The same problem, I really want to turn off this beeping when open the 🚪. Should be some way to do it.
|
|
|
Post by guibulle on Jul 23, 2020 16:11:32 GMT
Still searching too....
|
|
|
Post by grinstaktoronto on Sept 8, 2020 21:34:22 GMT
Has anyone found a fix? I need to delete this beep warning for the trunk/hatch as well.
|
|