|
|
Post by webtrak on Feb 19, 2019 12:19:16 GMT
Is it possible to code that reverse lights flash out of phase with emergency flashers only when the emergency flashers are engaged?
Thank you!
|
|
|
|
Post by dv52 (Australia) on Feb 20, 2019 11:01:11 GMT
Is it possible to code that reverse lights flash out of phase with emergency flashers only when the emergency flashers are engaged? Thank you! webtrak: Hi. I've personally not done the tweak that you want to a mk7 FL - but I did write a set of instructions for a very similar lighting effect with the inner rear tail-light on a mk7 Golf. Anyhow, using the same theory, you could try the following: - Select the Central Electrics control module @ address hex09
- select Security Access and enter the magic number 31347
- select Adaptation
- Apply the settings for the 2 x Leuchte-sets Leuchte29RFL RA64 (right-side reversing light) & Leuchte28RFL LC11 (left-side reversing light) as shown below:
Lichtfunktion A > Rueckfahrlicht
Lichtfunktion B > Aktive Blinkfunktion hat ein auf 1 gesetztes zugeordnetes Bit in pa_dynamisch_blinken
Dimmwert AB > 100
Lichtansteuerung HD AB > only_if_closed
Lichtfunktion C > Blinken links Dunkelphase
Lichtfunktion D > Blinken rechts Dunkelphase
Dimmwert CD > 0
Dimming Direction CD > minimize
Lichtfunktion E > Rueckfahrlicht
Lichtfunktion F > not active
Dimmwert EF > 100
Dimming Direction EF > maximize
Lichtfunktion G > not active
Lichtfunktion H > not active
Dimmwert GH > 0
Dimming Direction GH 29 > maximize
- Change Außenlicht_Blinker
Warnblinken_Zuendung_AUS > active
Warnblinken_Zuendung_EIN > active
Don
|
|
|
|
Post by webtrak on Feb 22, 2019 18:15:03 GMT
All the original values in brackets are as you suggested, but my OBD11 crashes every time I try to change the dimmwert values. So, I am seeing if their customer support can help.
|
|
|
|
Post by webtrak on May 2, 2019 0:21:41 GMT
Hi Don - I finally got my OBDEleven back from a friend .
Checked out the values and unfortunately Leuchte 29RFL RA64 and 28RFL LC11 values do not match the baseline ones as you prescribed.
Is it a lost cause?
Thank you!
|
|
|
|
Post by vwjap on May 2, 2019 0:57:51 GMT
Are in mine dude   Although you have to scroll down a long way to find it |
|
|
|
Post by dv52 (Australia) on May 2, 2019 11:26:22 GMT
Hi Don - I finally got my OBDEleven back from a friend . Checked out the values and unfortunately Leuchte 29RFL RA64 and 28RFL LC11 values do not match the baseline ones as you prescribed. Is it a lost cause? Thank you! not sure i understand - post up your baseline values please |
|
|
|
Post by webtrak on May 2, 2019 15:48:34 GMT
Is it possible to code that reverse lights flash out of phase with emergency flashers only when the emergency flashers are engaged? Thank you! webtrak: Hi. I've personally not done the tweak that you want to a mk7 FL - but I did write a set of instructions for a very similar lighting effect with the inner rear tail-light on a mk7 Golf.
Anyhow, using the same theory, you could try the following:
- Select the Central Electrics control module @ address hex09
- select Security Access and enter the magic number 31347
- select Adaptation
- Make the changes listed below (note: the settings in brackets are the default settings. Check these default values first -do not try the tweak if ALL the default settings on your car are not as shown):
Leuchte29RFL RA64 (right-side reversing light)
Lichtfunktion C 29 > Aktive Blinkfunktion hat ein auf 1 gesetztes zugeordnetes Bit in pa_dynamisch_blinken (not active)
Dimmwert CD 29 > 100 (0)
Leuchte28RFL LC11 (left-side reversing light)
Lichtfunktion C 28 > Aktive Blinkfunktion hat ein auf 1 gesetztes zugeordnetes Bit in pa_dynamisch_blinken (not active)
Dimmwert CD 28 > 100 (0)
Außenlicht_Blinker
ZV_Blinken_auf > active (not active)
ZV_Blinken_zu > active (not active)
Don
So... I got this far and the reverse come on STEADILY with flashers. What else to try make them flash in or out of phase with flashers? |
|
|
|
Post by webtrak on May 2, 2019 17:14:11 GMT
In my earlier post, I had confused the meaning of bracketed values with the new values.
After successful programming via OBDEleven, the reverse lights would come on steady if the flashers were on, OR either turn signal.
If I used blinken hell- or dunkelphase, they would blink appropriately with the flashers, but also with the turn signals.
|
|
|
|
Post by dv52 (Australia) on May 2, 2019 23:51:42 GMT
In my earlier post, I had confused the meaning of bracketed values with the new values. After successful programming via OBDEleven, the reverse lights would come on steady if the flashers were on, OR either turn signal. If I used blinken hell- or dunkelphase, they would blink appropriately with the flashers, but also with the turn signals. webtrak: hmm........... my error (apology)
I've changed the adaptation channels in Außenlicht_Blinker in my original instructions (see red colored channels)
So, do this:
1. Return
ZV_Blinken_auf > not active
ZV_Blinken_zu > not active
2. Then activate the 2 x red colored channels in my (changed) instructions
Don
|
|
|
|
Post by webtrak on May 3, 2019 14:30:04 GMT
Hi Don -
Did everything in the new recommendations and reverse light stays solid during turn signal and flashers.
One thing to note:
ZV_Blinken zu and auf were ALREADY not active. Does that info help?
Thank you!
Bill
|
|
|
|
Post by dv52 (Australia) on May 3, 2019 22:18:40 GMT
^^^^ Third time lucky - changed my instructions once more. Try again (if you want)
Don
|
|
|
|
Post by webtrak on May 4, 2019 0:17:25 GMT
Hahahaha! I will (once I return from my trip on Sunday). Many thanks for your patience!!
|
|
|
|
Post by webtrak on May 6, 2019 23:46:31 GMT
Ahhh no luck.
With this configuration, the reverse light stays on even with the turn signal (not just flasher) ...now BOTH reverse lights flash, no matter if left or right turn indicator is actuated.
|
|
|
|
Post by dv52 (Australia) on May 7, 2019 1:31:22 GMT
webtrack: hmm............ got me stumped!!! Any chance that you could drive your car down here to my workshop in Melbourne, Australia?  |
|
|
|
Post by webtrak on May 7, 2019 11:00:36 GMT
I plan someday to chase summer around the globe as I have endured too many Michigan winters! Melbourne is tops on my travel list!
Thank you for your efforts! I will keep on experimenting, following your methodology and see what happens!
All the best to you Don,
Bill
|
|
2018gti
Full Member
2018 GTI Autobahn 6-speed
Posts: 111
|
Post by 2018gti on May 9, 2019 2:17:26 GMT
Hi webtrak, I may have a solution for you. (1) As mentioned above, in Aussenlicht_Blinker, set the following: Warnblinken_Zuendung_EIN:
active
Warnblinken_Zuendung_AUS:
activeAnd try this, to make sure they don't come on when you're just using your regular turn signal (** haven't tried this though - make sure your turn signals still work after this  **): ZV_Blinken_zu:
not active
ZV_Blinken_auf:
not active
Richtungs_blinken_rechts:
not active
Richtungs_blinken_links:
not active
(2) In Leuchte28RFL LC11 (left reverse light), make the following changes (shown as ">>>>>>>"): Leuchte28RFL LC11:
Lasttyp 28:
43 - allgemeine LED
Lampendefektbitposition 28:
b
Fehlerort mittleres Byte DTC-DFCC 28:
31
Lichtfunktion A 28:
Rueckfahrlicht >>>>>>> Aktive Blinkfunktion hat ein auf 1 gesetztes zugeordnetes Bit in pa_dynamisch_blinken
Lichtfunktion B 28:
nicht aktiv
Dimmwert AB 28:
127
Lichtansteuerung HD AB 28:
always
Lichtfunktion C 28:
nicht aktiv >>>>>>>> nicht_definiert_4C
Lichtfunktion D 28:
nicht aktiv
Dimmwert CD 28:
0
Dimming Direction CD 28:
maximize >>>>>>>> minimize
Lichtfunktion E 28:
nicht aktiv >>>>>>>> Rueckfahrlicht
Lichtfunktion F 28:
nicht aktiv
Dimmwert EF 28:
0 >>>>>>>> 127
Dimming Direction EF 28:
maximize
Lichtfunktion G 28:
nicht aktiv
Lichtfunktion H 28:
nicht aktiv
Dimmwert GH 28:
0
Dimming Direction GH 28:
maximize(3) In Leuchte29RFL RA64, perform the same changes you made to Leuchte28. Should be identical. Hope this works!! Disclaimer: this is just off the top of my head. Test your turn signals and reverse lights afterwards  . |
|
|
|
Post by webtrak on Aug 13, 2019 0:43:09 GMT
Alas.... even with the guidance you provided, the flashers work correctly and the reverse lamps flash out of phase like I want...
BUT
Both reverse lights glow steadily when I indicate left or right. The rear indicators blink correctly.
Sigh.
|
|
|
|
Post by webtrak on Aug 13, 2019 1:14:16 GMT
Out of sheer desperation, I went through each step again. Undid then re-did each one...
SUCCESS!!!!!!
Many thanks to all!!!!
Once I figure out how to post the video I will!
|
|
|
|
Post by webtrak on Aug 13, 2019 1:46:12 GMT
|
|
**):
.