|
|
Post by Carolco on Feb 6, 2019 19:52:16 GMT
Hi everybody.
in the last version of OBDeleven, when I scan all the units the 5F is lost.
if I want that it appears visible I have to uncheck and check in the unit list.
any idea for this?
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 6, 2019 20:45:16 GMT
first thing I would do is this first
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 8, 2019 16:26:28 GMT
if this does not solve it please let us know and also advise if you are a member of the Beta test group.
Thanks
|
|
|
|
Post by heli17 on Feb 9, 2019 12:56:16 GMT
Hallo,
Ich kann auf das Steuergerät 5F auch nicht mehr zugreifen.
Ich hab das vom YouTube Video probiert, leider ohne Erfolg.
Gibt es noch eine Lösung?
Mfg. Heli
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 10, 2019 18:50:46 GMT
wenn Sie die Anweisungen von carolco befolgen
Wenn ich möchte, dass es sichtbar erscheint, muss ich die Einheitenliste deaktivieren und überprüfen. Lassen Sie uns wissen, ob das funktioniert.
Können Sie die Steuereinheit sehen, aber keine Optionen damit.
Welche Farbe hat der Status der Steuereinheit? (Schwarz, Grün oder Rot)
|
|
|
|
Post by Carolco on Feb 10, 2019 23:15:04 GMT
Hello.
not appear the 5F module when scan the units.
any other sugestión?
|
|
|
|
Post by heli17 on Feb 11, 2019 12:50:59 GMT
Hallo,
Danke für die Hilfe.
Ich habe es nach den Anweisungen von Carolco versucht.
Leider keine Veränderung.
Das Steuergerät wird mir nach dem Scannen angezeigt. In meinem Fall mit einem roten Punkt für Fehler im Fehlerspeicher.
Wenn ich dann auf das Steuergerät tippe bekomme ich die Meldung "Steuergerät reagiert nicht. Zündung überprüfen und nochmals versuchen."
Versuche ich es nochmals kommt immer diese Meldung.
Gehe ich auf abbrechen wird das Steuergerät mit einem schwarzen Punkt angezeigt.
Bitte um Hilfe. Danke
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 11, 2019 13:36:50 GMT
Rufen Sie das Problem mithilfe der Hilfefunktion in der App beim Support-Team auf. Wenn es schwarz wird, bedeutet dies, dass die Steuereinheit nicht mehr funktioniert. Ich gehe davon aus, dass sie vor dem letzten Software-Upgrade funktioniert hat und nicht funktioniert
|
|
2018gti
Full Member
2018 GTI Autobahn 6-speed
Posts: 111
|
Post by 2018gti on Feb 19, 2019 19:51:43 GMT
I also have this problem and I reported it a couple months ago through the OBDeleven support. It hasn’t been fixed, as far as I know. But, there is a workaround: when you are viewing the list of control units, just refresh the page (pull down), then unit 5F will show up.
OBDeleven, you have a lot of bugs... Some fixes would be appreciated. We pay money for your service and for your device.
|
|
|
|
Post by whytey on Mar 1, 2019 19:40:43 GMT
Annoyingly I also have this with my GTI 7.5 and neither clearing the app cache and data or the refresh under control units allows me to see the 5f control unit I had planned to retrofit a rear view camera this weekend  |
|
|
|
Post by Thirsty on Mar 1, 2019 20:01:01 GMT
Annoyingly I also have this with my GTI 7.5 and neither clearing the app cache and data or the refresh under control units allows me to see the 5f control unit I had planned to retrofit a rear view camera this weekend Have you checked if it's in the gateaway list? |
|
|
|
Post by whytey on Mar 1, 2019 21:34:27 GMT
Annoyingly I also have this with my GTI 7.5 and neither clearing the app cache and data or the refresh under control units allows me to see the 5f control unit I had planned to retrofit a rear view camera this weekend Have you checked if it's in the gateway list? Evening sorry do you mean the rear view option? I have changed camera type within the Parking Assistance 76 module to rear view camera I'm under impression i also need to change Byte 19 bit 4 to activated within 5f module. Could this be accessed with the gateway module? |
|
|
|
Post by Thirsty on Mar 1, 2019 21:59:27 GMT
What i mean: there's a little green circle with a pen in your ECU list and with this you can add and remove ECUs from your view.
If 5F isn't checked then it won't appear.
|
|
|
|
Post by dv52 (Australia) on Mar 2, 2019 4:25:13 GMT
Annoyingly I also have this with my GTI 7.5 and neither clearing the app cache and data or the refresh under control units allows me to see the 5f control unit I had planned to retrofit a rear view camera this weekend Have you checked if it's in the gateaway list? Thirsty: Hi
I suspect that you are assuming that OP will install a new control module @ address hex6C as part of his/her rear view camera retro-fit. This is not normally required on a mk7 and it's quite a complicated task given that it requires the installation of a new wiring loom and the fitment of other components.
More than likely, I suspect that OP intends to only install the rear view camera in the closable VW symbol (on the trunk-lid). If so, the Wiring for the project looks like this:
Notice the absence of any connections to the CAN network - this means that for this type of installation, the rear-camera system does not need to be registered with the Gateway module. All that needs to happen is that the module @ address hex5F must be told that the rearview camera is installed and to start using it. This is done via the software switch in the module's code-string
Please forgive my reply if you already knew this
Don
|
|
|
|
Post by whytey on Mar 2, 2019 8:29:23 GMT
Have you checked if it's in the gateaway list? Thirsty: Hi
I suspect that you are assuming that OP will install a new control module @ address hex6C as part of his/her rear view camera retro-fit. This is not normally required on a mk7 and it's quite a complicated task given that it requires the installation of a new wiring loom and the fitment of other components.
More than likely, I suspect that OP intends to only install the rear view camera in the closable VW symbol (on the trunk-lid). If so, the Wiring for the project looks like this:
Notice the absence of any connections to the CAN network - this means that for this type of installation, the rear-camera system does not need to be registered with the Gateway module. All that needs to happen is that the module @ address hex5F must be told that the rearview camera is installed and to start using it. This is done via the software switch in the module's code-string
Please forgive my reply if you already knew this
Don
Thanks very much that's exactly what I'm doing to test the camera prior to running the cables I have it sat in the passenger seat and it appears to be working as required except I can't make the coding change. I will.now try to enable the module again but this did not work yesyerday |
|
|
|
Post by whytey on Mar 2, 2019 8:44:10 GMT
Hello I have checked and Multimedia 5f is selected but even after refreshing it still won't appear?
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Mar 2, 2019 10:36:23 GMT
whytey if you are not a member of the Beta testing group (which will be closing down in the near future) may I suggest you upgrade to the beta version forum.obdeleven.com/thread/463/registration as there were a few issues with the last release. You can always leave the group but this should hopefully get you seeing all your control units
|
|
|
|
Post by whytey on Mar 2, 2019 14:10:15 GMT
whytey if you are not a member of the Beta testing group (which will be closing down in the near future) may I suggest you upgrade to the beta version forum.obdeleven.com/thread/463/registration as there were a few issues with the last release. You can always leave the group but this should hopefully get you seeing all your control units Thanks very much I'll do that now as the camera and harness are now installed just need to code |
|
|
|
Post by whytey on Mar 3, 2019 13:38:26 GMT
Joined the beta group via link whether it was this or my constant refreshing of the screen I could eventually see 5f module and have now coded camera and it’s working great
|
|
|
|
Post by meremenko on Nov 18, 2019 10:32:04 GMT
Same issue here - no F5 on the list, even though it's enabled in the gateway list
|
|
|
|
Post by kaluzu on May 1, 2020 15:12:58 GMT
What i mean: there's a little green circle with a pen in your ECU list and with this you can add and remove ECUs from your view. If 5F isn't checked then it won't appear. Is this part of the iOS app? I cannot seem to have this option available to add/remove Control Units. |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on May 1, 2020 15:22:38 GMT
not according to this
Third QuarterUpdate 6 Output test Gateway codingControl unit reset |
|
