Post by olinix on Sept 24, 2018 6:37:40 GMT
Hi, I’m hoping someone can help me....
First off the vital stats of the car: 2005 A4 B7 3.0TDI (BKN engine) Quattro, ECU is using KWP2000
I am trying to adapt the throttle valve as i have recently rebuilt the whole engine and cleaned out the throttle as part of the process. Every instruction I can find says to do the following:
Turn the key on but do not start the car.
[Select]
[01 - Engine]
[Basic Settings - 04]
Group 060
[Go!]
It should say "Basic Settings: OFF" on the top of your screen.
Click [ON/OFF/Next] to turn on Basic Settings.
It should now say "Basic Settings: ON" on the top of your screen. Once you do this you will see the top right display say ADP RUN. The TB adaptation is being done as soon as you switched basic settings on. You will see the values change and hear the TB cycle for the first few seconds then it will stop. Leave it in Basic Settings for about 30 seconds.
Click [ON/OFF/Next] to turn off Basic Settings.
It should now say "Basic Settings: OFF" on the top of your screen
Click the [Done, Go Back] button and you're all set.
However, when I try to go to channel 060 in the Engine module I just get an error and I cannot run the adaption. I have fault codes for the throttle activation failed and clearing them first makes no difference, they come back straight away. Any help will be greatly appreciated, this is the last hurdle to getting the car back on the road!
Scan as below:
OBDeleven data log
Date: 2018-09-22 11:48
VIN: WAUZZZxxxxxxxxxx
Car: Audi A4
Year: 2005
Body type: Avant
Engine: BKN 150 kW (204 HP) 3.0 l
Mileage: 269190 KM
---------------------------------------------------------------
01 Engine
System description: 3.0L V6TDI G000AG
Software number: 8E0910401F
Software version: 0060
Hardware number: 8E0907401AJ
Coding: 0011171
Trouble codes:
P3243 - Throttle valve control module activation Electrical error Lower limit not reached
static
P0638 - Throttle Actuator Control (Bank1) Range/Performance Lower limit not reached
static
First off the vital stats of the car: 2005 A4 B7 3.0TDI (BKN engine) Quattro, ECU is using KWP2000
I am trying to adapt the throttle valve as i have recently rebuilt the whole engine and cleaned out the throttle as part of the process. Every instruction I can find says to do the following:
Turn the key on but do not start the car.
[Select]
[01 - Engine]
[Basic Settings - 04]
Group 060
[Go!]
It should say "Basic Settings: OFF" on the top of your screen.
Click [ON/OFF/Next] to turn on Basic Settings.
It should now say "Basic Settings: ON" on the top of your screen. Once you do this you will see the top right display say ADP RUN. The TB adaptation is being done as soon as you switched basic settings on. You will see the values change and hear the TB cycle for the first few seconds then it will stop. Leave it in Basic Settings for about 30 seconds.
Click [ON/OFF/Next] to turn off Basic Settings.
It should now say "Basic Settings: OFF" on the top of your screen
Click the [Done, Go Back] button and you're all set.
However, when I try to go to channel 060 in the Engine module I just get an error and I cannot run the adaption. I have fault codes for the throttle activation failed and clearing them first makes no difference, they come back straight away. Any help will be greatly appreciated, this is the last hurdle to getting the car back on the road!
Scan as below:
OBDeleven data log
Date: 2018-09-22 11:48
VIN: WAUZZZxxxxxxxxxx
Car: Audi A4
Year: 2005
Body type: Avant
Engine: BKN 150 kW (204 HP) 3.0 l
Mileage: 269190 KM
---------------------------------------------------------------
01 Engine
System description: 3.0L V6TDI G000AG
Software number: 8E0910401F
Software version: 0060
Hardware number: 8E0907401AJ
Coding: 0011171
Trouble codes:
P3243 - Throttle valve control module activation Electrical error Lower limit not reached
static
P0638 - Throttle Actuator Control (Bank1) Range/Performance Lower limit not reached
static