I cannot get my boot to open. Dealer programmed new key fob and it has not worked since. The wiring is ok at the hinge. badge switch is ok. Latch works with 12v. The trunk lights turn on when open, but dash does not recognize that it is open. There are 4 wires to the latch. three white wires. I cannot get the release wire to change state. I did find in adaptation that the rear door is off. Is this correct or how do I change it. Is there a coding module for the rear hatch/boot?
Did you or the deal made the mistake of coding the car to say that it has 2 locking motors instead of just 1 locking motor?
How are you sure that the wiring at the hinge is good (that's usually the culprit). I've read somewhere that the trunk latch is a "positive grounded" design where it is the negative terminals that close the circuit to operate things. The fact that your latch works with 12V doesn't tell us if you connected the 12V to the motor itself, or through the complete harness to confirm that the harness itself is good You may have an odd issue where the CECM / Central electronic module is fried in that portion of the circuitry somehow. It isn't a fuse problem as it is shared with the other doors. There is no "adaptation" for the
You need to post your full coding for your car so I can load it in VCDS and see what it looks like.
dv52 (Australia): @_Piotr: AFAIK, there are no PIDs that are directly accessible by the user in OBD11. The Parameter-IDs are incorporated into the software options. For example, service mode 03 (Show stored Diagnostic Trouble Codes)is accessed in "Fault"
May 27, 2020 22:22:20 GMT
2014a4: 3g Mimi update how to code
May 28, 2020 1:09:16 GMT
francesco78: DIsattivare stAR & STOP SU A4 B9, problemi quando il clima è acceso. Riporto tutto indietro con crediti tolti, ma nulla cambia.
May 28, 2020 7:17:49 GMT
bonjoir jai un probleme je peu: bonjour jai un probleme je peut pas coder l'unite 9 controle jai une polo 2019
May 28, 2020 19:59:05 GMT
sofianethiais: bonjour je peut pas coder lunité 9 controle unit de ma polo 2019 jai essayer avec iphone et android
May 28, 2020 20:02:49 GMT
senortoasty2000: Hello everyone, I was wondering if anyone knows how to use the OBDeleven to make it so the headlights I ordered (Ed's LEDS)have the amber LED turn signals always on. I have a 2017 base model GTI
May 29, 2020 0:11:19 GMT
majestic12: Hellol everyone, does anybody has also needle sweep lag ? its not smooth on my virtual cockpit. where can i report this ?
May 29, 2020 14:19:50 GMT
testeronline: majestic12 I would suggest you let VW/AUDI Know as this is there software. Just as an aside what car do you have as I did not think the virtual screens supported this so just trying to increase my knowledge
May 29, 2020 14:33:02 GMT
dv52 (Australia): testeronline: needle sweep can be enabled on some AID displays. In majestic12's case, I suspect the facility is getting delayed because of all of the other start-up activities that happen on ignition switch-on (but I'm guessing)
May 29, 2020 21:53:48 GMT
audia4b8: Hi, I have the same problem, did you manage to solve it? I have been struggling with this for a month and I also have no way of changing it as they write above. It is not possible to change 0 - 1 and vice versa. Through the application and points also does
May 30, 2020 5:58:23 GMT
majestic12: Yea i though so it would be the processes that are starting up when turning on the ignition, maybe they can fix it by doing needle sweep when turning the engine on. Would be cooler to me when starting the engine you see the needle sweep
May 30, 2020 9:44:56 GMT
vwjap: Needle sweep works fine on my AID
May 30, 2020 14:53:43 GMT
face0704: hello has someone a coding for skoda fabia 2017, to open the mirrors with the kessy remote?
May 31, 2020 5:20:24 GMT
testeronline: vwjap, I just checked on the Leon Forums and currently V1 and V2 of the dash does not support needle sweep, however it looks like v3 (as fitted in the Atteca) does. Lucky I have the old dials and they do support it (not that I ever look at it )
May 31, 2020 13:11:15 GMT
sgt1297: blackfist13: is there a problem with the car? If not reset all the error codes and see if they come back. If you have issues with the car go through each symptom using the fault codes as a reference. Make model and year?
Jun 1, 2020 19:50:49 GMT
vwlotech: hello, i wasn't able to locate exact trouble code in the search. My pass side mirror puddle light is not getting any power to it. this is what I'm seeing, all of my codes match the drivers door which is working fine, i tested the circuit
Jun 4, 2020 17:46:02 GMT
vwlotech: getting this code B13C801 - Door ambient lighting / lighting for speakers Electrical error static - Priority: 3 - Malfunction frequency counter: 6 - Unlearning counter: 83
Jun 4, 2020 17:50:16 GMT