|
|
Post by pyrotech1620 on Jun 22, 2018 22:55:54 GMT
Anyone have any idea on how to get the OPS display shown below to display when I put the car in reverse? I have seen some videos of it doing it but think they might be UK version of the MK7 and I have the NA version. I currently have to put it in reverse then wait a second and then press the "Menu" button that appears on screen to get it to display.  |
|
|
|
Post by dv52 (Australia) on Jun 23, 2018 1:35:03 GMT
Anyone have any idea on how to get the OPS display shown below to display when I put the car in reverse? I have seen some videos of it doing it but think they might be UK version of the MK7 and I have the NA version. I currently have to put it in reverse then wait a second and then press the "Menu" button that appears on screen to get it to display. Pyro: For obvious reasons, my understanding of equipment levels in NAR mk7s ain't that good - but try this: - Press the CAR button on the escutcheon plate for the MIB screen
- Select setup symbol on the lower right-side of the screen (looks like a couple of gears)
- Scroll down and select parking and maneuvering
- select Park Pilot
- make sure that the Active Automatically box is ticked
Don
|
|
|
|
Post by pyrotech1620 on Jun 23, 2018 14:34:01 GMT
Pyro: For obvious reasons, my understanding of equipment levels in NAR mk7s ain't that good - but try this: - Press the CAR button on the escutcheon plate for the MIB screen
- Select setup symbol on the lower right-side of the screen (looks like a couple of gears)
- Scroll down and select parking and maneuvering
- select Park Pilot
- make sure that the Active Automatically box is ticked
Don
I have tried that before with no luck. That seems to only impact if I am pulling into a parking spot the sensors will activate under a certain speed. However, it doesnt make them show-up when the car is put into reverse.. Was hoping there was a code setting since I had seen it on the UK version.. And yes the NAR mk7 and mk7.5 always get the good stuff taken out which really sucks.. =[ |
|
|
|
Post by ofektal8 on Jun 23, 2018 19:13:11 GMT
Pyro: For obvious reasons, my understanding of equipment levels in NAR mk7s ain't that good - but try this: - Press the CAR button on the escutcheon plate for the MIB screen
- Select setup symbol on the lower right-side of the screen (looks like a couple of gears)
- Scroll down and select parking and maneuvering
- select Park Pilot
- make sure that the Active Automatically box is ticked
Don
I have tried that before with no luck. That seems to only impact if I am pulling into a parking spot the sensors will activate under a certain speed. However, it doesnt make them show-up when the car is put into reverse.. Was hoping there was a code setting since I had seen it on the UK version.. And yes the NAR mk7 and mk7.5 always get the good stuff taken out which really sucks.. =[ activate automatically will just activate the sensors automatically below 15 km/h and show up on the screen while driving if it detects something. for your question, in the park assist module. in Visual Display for park assist make sure it is on OPS display or on 360 display if you have pla and on Camera type make sure you tell the car you have a camera so the parking sensors overlay what the rear view camera sees |
|
dazz
New Member
Posts: 12
|
Post by dazz on Jun 30, 2018 2:48:30 GMT
For some unknown reason, when I put the below to "On", that view on my Passat disappeared, went to the left of the MIB unit, and I had to manually select it each time I reversed to turn it on.
When I set the below
5F > Adaptations > Vehicle Configuration > OPS_display_in_dash_board_display_unit: Off
When I select "Off", it popped up automatically when reversing, like the above. Weird! Don't forget to Hard Boot the MIB unit (Hold off button for 10 secs). Maybe check the above setting, may work.
|
|
|
|
Post by vwjap on Jun 30, 2018 7:51:04 GMT
Because that adaption puts the ops in the clocks and turns it off the mmi,
|
|
dazz
New Member
Posts: 12
|
Post by dazz on Jun 30, 2018 10:36:20 GMT
aahhhhhh
|
|
|
|
Post by notorious on Jun 4, 2022 3:43:15 GMT
Anyone know how to code it for the Arteon? Tried the method for passats, however, the adaption couldn't be found.
|
|
