satli
New Member
Posts: 11 
|
Post by satli on Jan 17, 2018 16:42:53 GMT
Hello Golf 2017 comfortline I have a rain and light sensor but how do I encode the long koding part 00 00 00 in the code?
|
|
|
|
Post by dv52 (Australia) on Jan 18, 2018 3:39:18 GMT
Satli: the method for access to the RLS is shown below - the code shown is not for your car (it's for a Highline 103TSI mY13)  Don |
|
satli
New Member
Posts: 11
|
Post by satli on Jan 30, 2018 20:04:00 GMT
How do we encode the 09 Channel Long Coding part 0000000000000000000000 for 2017 Golf FL?
|
|
|
|
Post by vwjap on Jan 30, 2018 20:06:53 GMT
You can’t, there’s no long coding in central electronics
You have to code the subsystems
|
|
|
|
Post by dv52 (Australia) on Jan 30, 2018 23:30:42 GMT
How do we encode the 09 Channel Long Coding part 0000000000000000000000 for 2017 Golf FL? Salti: Since about early 2017, the "09 Channel" (which I assume you mean in OBD11 language to be the Central electrics module @ address hex09) has had a zero-string for it's coding. What happened in these later modules was that ALL the software switches that were in the code, were transferred to adaptation channels. So if you want to change a Byte/Bit that was in the old long coding section - search for the descriptor in the adaptation section of the module Don |
|
satli
New Member
Posts: 11
|
Post by satli on Feb 2, 2018 23:09:51 GMT
I'm looking for it, but I still can not find it.  |
|
|
|
Post by dv52 (Australia) on Feb 3, 2018 3:23:53 GMT
I'm looking for it, but I still can not find it. satli: If you are trying to register a retrofitted Rain sensor into the CAN network (as a LIN device) - try this: - Select Central electrics module (@ address hex09)
- Select security access
- Enter the magic number 31347
- Select adaptation
- Search for Assistance light functions
- Select Regen_Lichtsensor
- Set to LIN_REGEN_LICHT_SENSOR
This is the same as setting Byte 6, Bit 1 in the old version BCMs
Don
|
|
|
|
Post by opolat on Feb 3, 2018 14:07:49 GMT
Hi dv52
I did the operation you mentioned above and introduced the sensors. I can not find how the light switch is activated
Thanks
|
|
satli
New Member
Posts: 11
|
Post by satli on Feb 3, 2018 19:44:42 GMT
I'm looking for it, but I still can not find it. satli: If you are trying to register a retrofitted Rain sensor into the CAN network (as a LIN device) - try this: - Select Central electrics module (@ address hex09)
- Select security access
- Enter the magic number 31347
- Select adaptation
- Search for Assistance light functions
- Select Regen_Lichtsensor
- Set to LIN_REGEN_LICHT_SENSOR
This is the same as setting Byte 6, Bit 1 in the old version BCMs
Don
Byte 6, Bit 1 in We implemented this code. However, we will do what encoding for Bit 5, which is the central electrik> coding> long coding helper> BYTE 7 in automatic headlight switch mk7.  |
|
|
|
Post by dv52 (Australia) on Feb 3, 2018 23:18:55 GMT
Salti: Try this:
Select Central electrics module (@ address hex09)
Select security access
Enter the magic number 31347
Select adaptation
Search for Außenlicht_uebergreifend
Select LDS_mit_AFL
Set to Yes
Don
|
|
|
|
Post by premulus on Aug 4, 2019 11:05:55 GMT
Hi, after retrofiting light/rain sensor and ligts swith with auto position wipers working. Wire betvene light switch pos. 2 and bcm socet c pos. 16 instaled, but after coding unit have pernament fault: U110B00 - lights swith without comunication and if is ignition on main light is still on, in every position of light swit and tail fog lights cant tur on. Do you have any idea what is wrong? Car is eu spec with halogen headlights.
|
|
|
|
Post by dv52 (Australia) on Aug 7, 2019 0:29:19 GMT
^^^^ hmm........ more information needed!! We know what equipment was physically installed, but what coding changes did you make?
perhaps you might post-up the actual DTC message and also the code-string on the hex09 module AND the code-string on the new light-sensor
Don
|
|
|
|
Post by premulus on Aug 9, 2019 16:54:33 GMT
Lights issue solved. Wrong adaption setting repaired😎
|
|
