Wakki
New Member
Posts: 5
|
Post by Wakki on Feb 27, 2024 9:19:23 GMT
Hi,
Is there any coding for the rear wiper to delay its start when spraying the rear window with washer fluid. When the washer fluid lands on the rear window (top part of window) the rear wiper activates a little too fast imo, half the wiper drags dirt and the other half drags the fluid. I wan't to delay the rear wiper to start a little bit later so that the fluid can cover more of the window before it actually starts wiping.
Is this possible?
|
|
|
|
Post by dv52 (Australia) on Feb 28, 2024 2:03:45 GMT
Short answer - YES
Long answer: There are a bunch of aspects to the way the rear wiper works that is adjustable. I've listed below the channels in the central electrics module that pertain to the rear window wiper:
Rear Window Wiper
- Automatisches Heckwischen - Automatic rear wipe > not active
- Einzelansteuerung Heckintervallwischen - Individual control for rear interval wiping > not active
- Einzelansteuerung Heckintervallwischen Zeitintervall 1 - Individual control of rear interval wiping Time interval 1 > 8 s
- Einzelansteuerung Heckintervallwischen Zeitintervall 2 - Individual control of rear interval wipe time interval 2 > 16 s
- Heckwischer - Rear wiper > logikgesteuert -logic controlled
- Heckwischer Weiterlauf - Rear wiper continues running > not active
- Komfortwischen Heck - Comfortable rear wiper > active Komofortwische
- HeckIntervallpausenzeit Stufe 1 - Comfort wipe rear interval break time level 1 > 3 s
- Komofortwischen Heck Intervallpausenzeit Stufe 2 - Comfort wipe rear interval break time level 2 > 1 s
- Komofortwischen Heck Intervallpausenzeit Stufe Automatik - Comfort wiping rear interval pause time level automatic > 5 s
- Komofortwischen Heck Intervallpausenzeit Stufe Intervall - Comfort wipe rear interval pause time level interval > 5 s
- Menuesteuerung Komfortwischen HW - Menu control comfort wiping HW > not active
- Spannungsanforderung_konfig_Wischer - Voltage_requirement_config_wiper > Keine_Spannungsanforderung -No_voltage requirement
- Traenenwischen Heck - Tear wiping Heck > not active
- Zeit_wasch_min_heck - Time_wash_min_heck > 1000 ms
My table above has each channel listed like this: German Name - English equivalent >factory value
As factory set - access to (most of) these channels is disabled because the rear wiper is automatically controlled by the car's speed. To disable this facility - change channel 2. above: - Einzelansteuerung Heckintervallwischen > Unabhaengig_der_Fahrzeuggeschwindigkeit - Independent_of_vehicle_speed
This will allow the other channels to be altered. For your particular want - the interval before wipe commences can be altered by: - HeckIntervallpausenzeit Stufe 1 > increase value
I haven't played with the other channel values - if you experiment, please tell us your observations
Don
|
|
Wakki
New Member
Posts: 5
|
Post by Wakki on Feb 28, 2024 6:52:49 GMT
Short answer - YES
Long answer: There are a bunch of aspects to the way the rear wiper works that is adjustable. I've listed below the channels in the central electrics module that pertain to the rear window wiper:
Rear Window Wiper
- Automatisches Heckwischen - Automatic rear wipe > not active
- Einzelansteuerung Heckintervallwischen - Individual control for rear interval wiping > not active
- Einzelansteuerung Heckintervallwischen Zeitintervall 1 - Individual control of rear interval wiping Time interval 1 > 8 s
- Einzelansteuerung Heckintervallwischen Zeitintervall 2 - Individual control of rear interval wipe time interval 2 > 16 s
- Heckwischer - Rear wiper > logikgesteuert -logic controlled
- Heckwischer Weiterlauf - Rear wiper continues running > not active
- Komfortwischen Heck - Comfortable rear wiper > active Komofortwische
- HeckIntervallpausenzeit Stufe 1 - Comfort wipe rear interval break time level 1 > 3 s
- Komofortwischen Heck Intervallpausenzeit Stufe 2 - Comfort wipe rear interval break time level 2 > 1 s
- Komofortwischen Heck Intervallpausenzeit Stufe Automatik - Comfort wiping rear interval pause time level automatic > 5 s
- Komofortwischen Heck Intervallpausenzeit Stufe Intervall - Comfort wipe rear interval pause time level interval > 5 s
- Menuesteuerung Komfortwischen HW - Menu control comfort wiping HW > not active
- Spannungsanforderung_konfig_Wischer - Voltage_requirement_config_wiper > Keine_Spannungsanforderung -No_voltage requirement
- Traenenwischen Heck - Tear wiping Heck > not active
- Zeit_wasch_min_heck - Time_wash_min_heck > 1000 ms
My table above has each channel listed like this: German Name - English equivalent >factory value
As factory set - access to (most of) these channels is disabled because the rear wiper is automatically controlled by the car's speed. To disable this facility - change channel 2. above: - Einzelansteuerung Heckintervallwischen > Unabhaengig_der_Fahrzeuggeschwindigkeit - Independent_of_vehicle_speed
This will allow the other channels to be altered. For your particular want - the interval before wipe commences can be altered by: - HeckIntervallpausenzeit Stufe 1 > increase value
I haven't played with the other channel values - if you experiment, please tell us your observations
Don
Thank you very much dv. Just noticed I haven't extended my pro plan. As soon as I get it, I will report back! |
|
