jauho
New Member
Posts: 5
|
Post by jauho on Sept 13, 2023 11:50:10 GMT
Hello,
When I leave driver's seat for more than approx. 10s, the engine will shutdown. It doesn't matter if I leave keys inside or not (keyless access)
I would want engine to stay on. I live in Finland, and we get lots of snow in winter. It's common to start the engine to warm it up, while getting snow off from windows and roof.
|
|
|
|
Post by dv52 (Australia) on Sept 13, 2023 22:47:43 GMT
hmm....... not sure about the engine switching-off with the driver seat empty - but the tweak to keep the engine running on a car with kessy and the key outside the car (clearly therefore with the driver seat empty) is as follows: 09 central electrics module Adaptation
ZV allgemein - Funk bei Klemme 15 ein change setting to active
Because it's an easy try - worth a shot IMO (revert setting back to original value if it doesn't work)
Don
|
|
|
|
Post by MartiniB on Sept 14, 2023 8:12:32 GMT
dv52 (Australia) I understood this option differently Enable Lock/Unlock via Key Fob with Ignition On
09 Central Electronics Access Code 31347 Adaptation -> ZV allgemein(Access control) ---> Funk bei Klemm 15 ein: ------> not active -> Active Enable passive Lock/Unlock via Door Handle Sensors (KESSY) with Ignition On
B7 Access Startsystem Interface Access Code 20103 Long Coding orig. 0F20000723 ---> 1F20000723 or -> Terminal 15 characteristics of passive entry exit function ---> orig. Function only allowed for terminal 15 off ---> new. Function only allowed for terminal 15 on or off
|
|
|
|
Post by sergi0dj on Sept 14, 2023 17:13:25 GMT
Hello, what if I don't have (KESSY), I have the usual key, the one inserted behind the steering wheel, and I don't want the engine to turn off when leaving the vehicle? What coding should I do to keep the engine running without being in the seat?
|
|
|
|
Post by dv52 (Australia) on Sept 14, 2023 22:08:37 GMT
MartiniB : Yes, you are correct - but I had understood that OP wanted the first tweak in your reply (it still works with KESSY with the key-fob outside the car - regardless of the lock/unlock status) Don
|
|
jauho
New Member
Posts: 5
|
Post by jauho on Sept 19, 2023 10:09:19 GMT
hmm....... not sure about the engine switching-off with the driver seat empty - but the tweak to keep the engine running on a car with kessy and the key outside the car (clearly therefore with the driver seat empty) is as follows: 09 central electrics module Adaptation
ZV allgemein - Funk bei Klemme 15 ein change setting to active
Because it's an easy try - worth a shot IMO (revert setting back to original value if it doesn't work)
Don
This didn't work.
Seems like opening driver's door will cut the ignition; when I open the door, there's "OFF" in the left corner next to RPM gauge
|
|
|
|
Post by dv52 (Australia) on Sept 19, 2023 23:59:14 GMT
jauho : OK - then I need to apologize to MartiniB because his advice is correct (my bad)!! So, using MartiniB instructions, do this: - Fire-up OBD11 software and connect to dongle
- Navigate to B7 Access Startsystem Interface module
- Select Long Coding - make sure the "Car" tab is selected (i.e. the extreme left-side tab on the upper row - see picture below)
- Select Terminal 15 characteristics of passive entry exit function (it's the first entry in the list)
- Set value = function only allowed for terminal 15 off (this is equivalent to setting Byte 00, Bit 0=1)
- Select SLIDE TO WRITE
- If prompted for an Access Code, enter 20103
- Exit OBD11 software - cycle ignition key
Don
|
|
jauho
New Member
Posts: 5
|
Post by jauho on Sept 21, 2023 19:00:40 GMT
It was coded already "function only allowed for terminal 15 off", so this wasn't the correct solution.  |
|
|
|
Post by dv52 (Australia) on Sept 21, 2023 22:01:52 GMT
try the other option "Function only allowed for terminal 15 on or off" as suggested by MartiniB |
|
jauho
New Member
Posts: 5
|
Post by jauho on Sept 22, 2023 16:51:23 GMT
|
|
