|
|
Post by koldico on Sept 10, 2023 20:22:57 GMT
I just mounted on my Tiguan blistein B16Damptronic, can the dcc suspension be regulated or calibrated with obd?
|
|
|
|
Post by koldico on Sept 14, 2023 17:39:15 GMT
I just tried to do the calibration and it didn't let me, it gave me an error, tomorrow I will try again to see if it will let me.
|
|
|
|
Post by koldico on Sept 15, 2023 2:47:01 GMT
I have done it with the ignition on, front hood open without handbrake and in position N of the gearbox, it may be that it should be in P and the handbrake applied
|
|
|
|
Post by MartiniB on Sept 15, 2023 8:05:10 GMT
have you made it from both sections?
i also weren't able do re-calibration on Superb Mk3.FL 2023
and just later noticed, i tried do it just from one of two,
can't remember now, which exact, Adaptations or Basic Settings
but your idea about N and Handbrake i also will try at next attempt
|
|
|
|
Post by koldico on Sept 15, 2023 10:15:47 GMT
I haven't gotten anything, I even put the code in the code and the next thing it asks me for the code again and it goes into loop mode and I don't go from there. I'll have to try Odis to see if there's any better luck.
|
|
|
|
Post by koldico on Sept 15, 2023 10:19:30 GMT
I have tried everything with the 2 options but since the first one doesn't work for me, there is no way, plus I get different errors, not always the same one, so I don't know, I hope that with the Odis I do better and I can do it.
|
|
|
|
Post by koldico on Sept 16, 2023 9:49:27 GMT
I have found this other way.
Looking at the service manual, it talks about performing
a Basic Setting "DCC" is reset when something in the
The suspension is changed (ball joint, springs, etc.).
The basic configuration screen for the DCC module has three
options
Adaptation with offset wheels
* Reset control module delivery status
maker
* Restore vehicle specific data
Does anyone know what these three options do? And what
Does it correspond to performing a dcc reset?
The VCDS forums state that you have to lift the car in the air (so that
suspension is in full droop), then perform a DCC
Reset basic settings.
Address 14: Susp. Elect. (J250) Login: 31564, Basic
Settings: Channel: 1 On/Off
I hope it works
|
|
|
|
Post by koldico on Sept 21, 2023 13:31:55 GMT
Well colleagues have already answered me about blistein, and as we thought after installing suspension with dcc you always have to make a basic adjustment, so one thing is more certain, tomorrow I will try to do it in the workshop that installed it for me with the obd and with their machine , and if I don't get it, I'll do it at the official VW service, and that's it.
|
|
|
|
Post by koldico on Sept 23, 2023 6:39:03 GMT
Sorry for the delay, they basically adjusted it for me the first time with their Bosch machine, in principle everything the first time and without problem. I have checked the data with the OBD, I have done a new scan, it has not given any errors and the data has not changed, it remains the same as with the original ones, so when I am going to change the rear lights under warranty, I will tell them to make an adjustment. basic to see if anything changes. In the workshop they have done it perfectly according to the program, so I am calm about that, the wheels are raised without touching the ground, the hood is raised, it makes the basic adjustment and when it goes down and the wheels are rested, it makes another one and that's it.
|
|
