|
|
Post by peterwholm on Jun 24, 2017 14:39:10 GMT
I am trying to find the channels to do some coding of the LED tail lights on my Passat. I've managed to locate the channels for the inner and outer RH/LH strip in the middle of the tail light. On picture 2 below the outer RH+LH inner strip is on (channel 23+24). But I haven't managed to find the channels that controls the "outer rim", so I can turn on the entire tail lamp (position/park light) as on picture 3. Does anyone know which channels I should use?    |
|
|
|
Post by peterwholm on Jun 24, 2017 16:12:06 GMT
It is this part of the tail light, for which I seek the channels. Anyone?  |
|
rbb
New Member
Posts: 4 
|
Post by rbb on Jun 24, 2017 17:08:00 GMT
I think they are 16 and 17 as they are position and brake light
|
|
|
|
Post by peterwholm on Jun 25, 2017 14:20:21 GMT
I think they are 16 and 17 as they are position and brake light Thank you - those were the channels I was looking for. In order to turn on the entire tail light the following channels shall be used: 16 17 23 24 27 Thanks again. |
|
rbb
New Member
Posts: 4
|
Post by rbb on Jun 26, 2017 6:40:04 GMT
Good, I'm glad these channels were what you were looking for.
What has been the modification that you have done so that the back light is daylight?
|
|
|
|
Post by peterwholm on Jun 26, 2017 7:21:56 GMT
Yes - exactly! I wanted to modify my cars DRL, so that my front park light and DRL was on (during daytime - see picture below), as well as my tail lights. My Passat light switch has four positions ("0", Auto, Park, Night time light). If I took the easy way and coded DRL = Park light, then my VW navigation went into "night mode", numberplate lamp, cabin switch light, cabin ambient light and so on was on. Especially the navigation in night mode was a pain in the.... Som now I've coded the following: DRL with front C-light (GTE) and front parklight. (Normally only C-light as DRL). DRL with the above mentioned taillight channels on (the same as night time light). I also chose to alter the light switch setting in "0", so it is as below: Position "0": All exterior light off (standard = DRL). Position "Auto": DRL (during daytime :-) ) with head- and taillights on as described above. Standard setting. Position "Park": As "Auto" but with navi in nightmode, light in interior switches, cabin ambient light on etc. Position "Night time light": As "Park" but with near light on in headlamps.  |
|
|
|
Post by B8 on Sept 29, 2017 6:09:48 GMT
Hello,
Can anyone help, i want my taillights to be on this way:
DRL= nothing in the rear is on
Normal lights = only outer rings at the rear are on, just like in PeterWholm photo shows.
This is the DRL mod for outer rings, but i want this mode in "normal running" mode:
Rear lights outer LED rings as DRL
Select Control unit 09 (Central Electrics)
Security access
Access Code 31347
Adaptation
Leuchte16 - Lightfunction D16 change from non-active to Daylight running lights
Leuchte17 - Lightfunction D17 change from non-active to Daylight running lights
Help, anyone?
|
|
|
|
Post by dark975 on Jan 4, 2018 3:56:01 GMT
Hi Peter,
can you please name these below channels (16,17,23,24,27) that you used for the task. I thought there should be 6 channels to torn on the entire light. 2 for outer rings, 2 for outer stripes and 2 for inner stripes ? Also can you please post the coding you did with these channels to achieve the results you got for the below tasks. Thanks in advance.
DRL with front C-light (GTE) and front parklight. (Normally only C-light as DRL).
DRL with the above mentioned taillight channels on (the same as night time light).
|
|
|
|
Post by BikeNutt on Jan 29, 2018 19:41:51 GMT
Hello, Can anyone help, i want my taillights to be on this way: DRL= nothing in the rear is on Normal lights = only outer rings at the rear are on, just like in PeterWholm photo shows. This is the DRL mod for outer rings, but i want this mode in "normal running" mode: Rear lights outer LED rings as DRL Select Control unit 09 (Central Electrics) Security access Access Code 31347 Adaptation Leuchte16 - Lightfunction D16 change from non-active to Daylight running lights Leuchte17 - Lightfunction D17 change from non-active to Daylight running lights Help, anyone? Sorry, I'm unable to help but I wanted to say thanks for posting the outer rear DRL setting. I've now set up my B8 this way. |
|
|
|
Post by blacky on Jun 7, 2018 21:13:01 GMT
This might be an offtopic but does anyone know can standard LED tail lights be replaced with Highline or r-line (plus minus) version and does it need some coding or different cables or is it just plug and play
|
|
|
|
Post by jollexd on Jun 17, 2020 14:38:52 GMT
hey peterwholm, you haven't solved it? "But I haven't managed to find the channels that controls the "outer rim", so I can turn on the entire tail lamp (position/park light) as on picture 3. I also want to fix it..  |
|
|
|
Post by dsgauto on Aug 18, 2020 11:39:32 GMT
Have anyone done this complete? I did it but it only worked for DRL, but I want to have them as parklights and how can I do so? Because I want the 0/DRL to have no rear lights (saving energy on my Passat GTE  ) |
|
|
|
Post by hoesty on Oct 24, 2020 23:50:27 GMT
peterwholm hi mate how do I access the light coding in obdeleven? I want to get the rear DRL's to stay on in the auto position on my audi q3 2013....i can't find any light code options listing in the adaption setting hope you can help j
|
|
|
|
Post by qdeado on Oct 27, 2020 11:42:23 GMT
Anyone knows if its possible to get rear blinker inner and outer leds both (ch 16 and 18 or 17 and 19) to blink simultaniously ?
|
|
|
|
Post by qdeado on Dec 28, 2020 21:10:06 GMT
Bump. Any clue how to get both strips working as turn signal simultaneously ?  |
|
|
|
Post by ionutd on May 2, 2022 13:16:18 GMT
I am working on that right now. Hopefully, in few hours I'll make them work. I also have found another thread somewhere which says G function on Leuchte 2sl and 3sl should be activated to work in a pace mode(not sure if it is for our B8). I'll be back.
L.E. No luck, both inner strips work on Leuchte 27 at the same time. There is no way you can separate them, or I didn't find it, yet. I'll give it another go next weekend.
|
|
PdM
New Member
Posts: 6
|
Post by PdM on May 5, 2022 19:47:15 GMT
Hi - anyone to solve this? Thanks a lot. Bump. Any clue how to get both strips working as turn signal simultaneously ? |
|
|
|
Post by rehman on May 15, 2024 17:47:17 GMT
Yes - exactly! I wanted to modify my cars DRL, so that my front park light and DRL was on (during daytime - see picture below), as well as my tail lights. My Passat light switch has four positions ("0", Auto, Park, Night time light). If I took the easy way and coded DRL = Park light, then my VW navigation went into "night mode", numberplate lamp, cabin switch light, cabin ambient light and so on was on. Especially the navigation in night mode was a pain in the.... Som now I've coded the following: DRL with front C-light (GTE) and front parklight. (Normally only C-light as DRL). DRL with the above mentioned taillight channels on (the same as night time light). I also chose to alter the light switch setting in "0", so it is as below: Position "0": All exterior light off (standard = DRL). Position "Auto": DRL (during daytime :-) ) with head- and taillights on as described above. Standard setting. Position "Park": As "Auto" but with navi in nightmode, light in interior switches, cabin ambient light on etc. Position "Night time light": As "Park" but with near light on in headlamps. |
|
|
|
Post by rehman on May 15, 2024 17:50:37 GMT
Hi, im trying to code the Parking lights to come on with the DRL’s without the rear taillights coming on as in the picture above. Is it possible? So I want the front parking lights to be on with the DRL’s
|
|
|
|
Post by sprucepassatb8 on May 27, 2024 8:29:41 GMT
Hi - anyone to solve this? Thanks a lot. Bump. Any clue how to get both strips working as turn signal simultaneously ? U wont be able to activate the whole light. No yellow lights are insighte the trunklights. |
|
|
|
Post by omartelinho on Jun 25, 2024 19:22:10 GMT
Hi there! I am willing to let only the "outer ring" on at night. Can anyone support??
Thank you
|
|
|
|
Post by sprucepassatb8 on Jun 26, 2024 7:28:17 GMT
Stg 09 (Zentralelektr.) Code: 31347 Adaption Leuchte23SL (outer Left light) Lichtfunktion A23 from 'Standlicht Allgemein (Schlusslicht, Positionslicht, Begrenzungslicht)' to 'not active' Leuchte24SL (outer Right light) Lichtfunktion A24 from 'Standlicht Allgemein (Schlusslicht, Positionslicht, Begrenzungslicht)' to 'not active' Leuchte27NSL (lights in the middl (trunk) Lichtfunktion A27 from 'Standlicht Allgemein (Schlusslicht, Positionslicht, Begrenzungslicht)' to 'not active' Thats the coding for your. |
|
)
