|
|
Post by kubinf on Jun 6, 2017 7:18:07 GMT
Hi,
does anyone know how to enable awareness assist function? I found some adaptations for it in Unit 09 (Central electrics) and now got the option in the settings, but every time I get error message "Function not available". Can you help me out?
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jun 6, 2017 10:48:55 GMT
kubinf can you please advise what model, year and sensors you have (eg do you have the radar and two sensors on your windscreen)
Also not fully sure what you mean by awareness assist could you give bit more info please (eg is this lane assist etc)
|
|
|
|
Post by kubinf on Jun 12, 2017 5:30:03 GMT
Hi,
thank you for answer.
Model is Leon ST X-Perience 2016 5F.
I do not have radar (acc) and front camera (lane assist).
By this assist I mean the function that keep the driver allert and suggests taking a break if the driver is going to fall asleep.
Also do you know if there is any way to adjust the range of the LED headlights using OBD? Mine are just to high and I would like to get them down.
Thank you
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jun 19, 2017 17:01:16 GMT
Sorry been away so catching up on stuff.
So what you are after is the Tiredness Detect function, what I have seen is that it monitors your steering wheel and accelerator usage. I don't have any code for this but will keep looking to see if I can find anything.
With regards to lights I am sure I have seen something on this on the Golf forums I will double check and get back later.
The other option as this is a 2016 car why don't you take it to the garage and get them to sort the lights..
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jun 20, 2017 10:26:53 GMT
Found the link for light adjustment have a read of this thread this is for an older model but expect its the same on yours. But the summary is if you want to adjust the up/down left/right you use the screws, if you want to adjust the motorway lights settings then you need vcds/obd11 (don't think you can change LED Brightness from memory) |
|
|
|
Post by kubinf on Jun 20, 2017 20:14:35 GMT
Thank you very much for your reply. Yes that is exactly that. I have found something in the General Electric, but now somehow I can't acces it anymore. Need to check it tommorrow.
|
|
|
|
Post by maxitaly on Jun 27, 2017 10:27:03 GMT
What about awareness assist function? Nothing found??
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jun 27, 2017 12:10:52 GMT
|
|
|
|
Post by xedos9er on Jun 28, 2017 20:00:07 GMT
Not possible, because SWaP
|
|
|
|
Post by kubinf on Jul 9, 2017 12:55:49 GMT
I have found something.
Can you please write here what number do you have in control unit 19 - long coding - mke_variante?
I have got it active and variante 5
|
|
|
|
Post by maxitaly on Jul 9, 2017 17:00:27 GMT
I just have this:
MKE Check box:
activated
|
|
|
|
Post by kubinf on Jan 30, 2018 19:55:33 GMT
I would like to open this topic once again. Is there anyone with a car that has this feature (Weariness recognition known as the Driver fatigue assistant) fitted from the factory? If so, could you please read the instructions below and write here what are your settings of these adaptations or codings? I found something on an Audi A4 forum, but it did not work for me. So up to today my process of trying and finding came to this: In control unit 19 (CAN Gateway) (you need to switch on the bytes and bites look) Byte 17 -> activated bit 0 (it is labelled as MKE checkbox or weariness recognition). Byte 18 is not labelled, but what I have found is that you need to have the coding of bits 00, so all bits should be deactivated if you deactivate all bits you should see a label "Variante 1". Control unit 5F (information control) Adaptations Car_function_adaptations_gen2 (there are 3 quite similar adaptations, so be sure to open the one without words "CAN" or "BAP") menu_display_weariness_rcognition -> change value to ACTIVATED menu_display_weariness_rcognition_over_threshold_high -> change value to ACTIVATED There are two other adaptations for weariness recognition, but leave them not activated These adaptations in Unit 5F are just to make this function visible in the car settings menu on the screen (I get a whole new submenu called "Drivers assistants", but when I want to open it I just got a message saying "Function not available") So this is the last step I got and I would be really grateful for any help. I understand and so did the guys on Audi forum, that you should code something in the Steering assistance unit or Drivers column unit, because this feature monitors the driving wheel. But I did not find anything like that. I will appreciate every response, it is not that I need this function, it is just the challenge of managing it till the end as I am sure you understand  |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 30, 2018 21:12:01 GMT
this is what I have on my 2014 car - I think it has the function fitted although I have never seen it in action.
menu_display_weariness_recognition:
activated
menu_display_weariness_recognition_clamp_15_off:
Not activated
menu_display_weariness_recognition_over_threshold_high:
activated
menu_display_weariness_recognition_standstill:
Not activated
menu_display_weariness_recognition_after_disclaimer:
Not activated
weariness_rcognition_0x22:
activated
weariness_rcognition_0x22_msg_bus:
Databus Infotainment
This is the adaptions I have on the steering wheel
Control unit: 44 Steering Assistance
System description: EPS_MQB_ZFLS
Software number: 3Q0909144F
Software version: 5043
Hardware number: 3Q0909144F
Hardware version: 503
ODX name: EV_SteerAssisMQB
ODX version: 010031
Backup name: steering 06 05 17
Long coding:
9103
Adaptations:
Activating and deactivating all development messages:
Development messages:
not active
Characteristic curve of steering assistance:
Driving profile selection button
Activation of pwr steering asst without engine running:
not active
XCP calibration protocol:
not active
Software end stop:
active
Straight line running:
active
Support power:
100%
Driving profile switchover:
Incremental, controlled over time
Download without rest bus:
Suspension data bus:
not active
RPM monitoring:
active
I will check out the control unit 19 later.
|
|
|
|
|
|
Post by kubinf on Feb 1, 2018 14:14:47 GMT
I checked your settings with mine and switch these two adaptations you listed above.
weariness_rcognition_0x22:
activated
weariness_rcognition_0x22_msg_bus:
Databus Infotainment
But the I still got the message "Function not available" on the center screen.
Do you see the option "weariness recognition" in the car - settings - drivers assistance?
The coding in Steering unit is the same, so I do not know if there is anything to change.
|
|
|
|
Post by itdisnawork on Sept 3, 2018 12:13:30 GMT
Has anybody been able to get this working? Trying to do this on my Kodiaq with no luck so far.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Sept 3, 2018 14:23:42 GMT
when you say no luck so far, do you mean you have an error or you have just not seen it work.
I have had it on my car from stock and I have only seen it come up max twice.
|
|
|
|
Post by kikihr on Sept 3, 2018 18:35:01 GMT
Not possible because of SWAP function. As well you can not activate pedestrian monitoring.
|
|
celia
New Member
Posts: 32
|
Post by celia on Feb 25, 2022 17:40:10 GMT
hi , how to buy SWap thanks
|
|
