magas
New Member
Posts: 2
|
Post by magas on Sept 22, 2022 13:20:16 GMT
USA 2017 Audi Q7 8B (ACC) module showing two C110300 errors (sensor misalignment) on cruise control module 8B. Module 13 is showing 1 (different) fault as well, perhaps due to 8B's issue. Trying to reset personalized settings after using the only available security code 20103 on my NextGen OBDeleven device with PRO license doesn't seem to do anything. There is also no option to reset misalignment angle as seen in someone's S6 video (https://www.youtube.com/watch?v=SlmP7EBCtyI&t=398s).
I tried manually entering 91153 and 89531 under security access with no luck.
Is it possible to reset misalignment values on this Q7? Live data shows angles within tolerance (less than 0.8 degree, assuming that's the spec/max deviation).
P.S. The ACC stopped working after 3 hours of highway driving with heavy load + trailer. Soon after unloading the error went away. On the way back (heavy load + trailer) it stopped working again, right after about 3 hours of driving. And this time the error didn't go away.
|
|
|
|
Post by drsnowmon on Mar 10, 2023 15:00:38 GMT
Hi, did you ever get to fix this problem? I'm having the same issue on my GTI. Just like you, mine was intermittent. It worked for 1 day, then the next day it stopped working. After about 2 weeks of having this issue, it became permanent with a message "Front Assist Not Available" on the middle dashboard
|
|
maz
New Member
Posts: 2
|
Post by maz on May 24, 2023 11:31:15 GMT
Hi!
To reset, you’ll first have to switch to “End of Assembly Line”, then follow the A6 video you saw on your tube by Mr-Fix. He didn’t show us that particular step (probably didn’t need it in his case or was already in another service mode “developer”).
Good luck.
|
|
|
|
Post by thiplf on Oct 26, 2023 2:18:53 GMT
USA 2017 Audi Q7 8B (ACC) module showing two C110300 errors (sensor misalignment) on cruise control module 8B. Module 13 is showing 1 (different) fault as well, perhaps due to 8B's issue. Trying to reset personalized settings after using the only available security code 20103 on my NextGen OBDeleven device with PRO license doesn't seem to do anything. There is also no option to reset misalignment angle as seen in someone's S6 video (https://www.youtube.com/watch?v=SlmP7EBCtyI&t=398s). I tried manually entering 91153 and 89531 under security access with no luck. Is it possible to reset misalignment values on this Q7? Live data shows angles within tolerance (less than 0.8 degree, assuming that's the spec/max deviation). P.S. The ACC stopped working after 3 hours of highway driving with heavy load + trailer. Soon after unloading the error went away. On the way back (heavy load + trailer) it stopped working again, right after about 3 hours of driving. And this time the error didn't go away. I'm facing the same problem. Did you figure it out? Hi! To reset, you’ll first have to switch to “End of Assembly Line”, then follow the A6 video you saw on your tube by Mr-Fix. He didn’t show us that particular step (probably didn’t need it in his case or was already in another service mode “developer”). Good luck. I switched to End of Assembly Line and I still can't see the option "Reset Misalignment" inside of Basic Settings. I also tried in Developer mode and it was the same. |
|
|
|
Post by gliptopolis on Nov 26, 2023 2:35:46 GMT
My 2019 Q7 has the reverse of the bolt setups I see online. The torx is on the front. My alignment was out by 2.02 and in order to bring it back to near 0 I ended up making my adjustments on the lower right side screw instead of the upper left screw. I figured out through trial and error (and several miles of driving) that I could get the changes I needed by using the "wrong" screw. It worked and the ACC works now so who am I to argue?
Anyway, it took about one and a half full turns to get it to almost perfect. It was my 8B driver's side that was faulting. I turned to the right. Be sure you're looking at the correct section for the one your adjusting... there's one for the driver's side and one for the passenger side.Make sure you're adjusting the side with the misalignment error. I did the key on key off reset once and then just let the system recalibrate over several miles of driving.
|
|
