|
|
Post by marcelsgti on Apr 14, 2017 10:06:02 GMT
Hi Guys,
just started using my ODB11 and i am loving it so far. :-)
I want to code Traffic Sign Recognition. I am located in Germany so no problem with the usage here.
Unfortunately i ran into a problem coding Traffic Sign recognition:
Traffic Sign Assist Activation
Select Control unit 5F (Information Electrical)
Adaptation
Select channel (63) vehicle function list BAP traffic_sign_recognition_0x21 Found
Değer=Active
Select channel (151) vehicle menu operation-menu_display_road_sign_identification Found
Değer=Active
Select channel (153) vehicle menu operation-menu_display_road_sign_identification_over_threshold_high Found
Değer=Active
Control unit A5 (front / advance camera)
Security access
Access Code 20103
Control unit Long Coding
Byte 1
Bit 0 Activate - "01 Traffic Sign Recognition (FTE) active" Found
Select Control unit 17 (Dashboard)
Control unit Long Coding
Byte 5
Bit 2 Aktivate Found
Control unit A5 (front / advance camera)
Adaptation
Select : channel numbers indicate end of speed limit (Not found)
Importance to actively invest Show Valid suffix
View Channel Valid suffix
Corresponding value adjust default: 00100111
I don't really understand and can't find the last section anywhere? Could you please help me get this running?
Thanks!!!
Best regards,
Marcel
|
|
|
|
Post by dv52 (Australia) on Apr 14, 2017 12:01:31 GMT
^^Hmm..... just a guess but try this:
Control unit A5 (front / advance camera)
Security Access
20103
Adaptation
Select: " Zeichen Ende der Geschwindigkeitsbegrenzung" (mark the end of the speed limit)> set to "active"
Don
|
|
|
|
Post by marcelsgti on Apr 14, 2017 12:33:11 GMT
Hi Don, i also found that but the description looks totally different to this simple activation  Has anybody already done it and is able to help? Marcel |
|
|
|
Post by marcelsgti on Apr 14, 2017 20:06:38 GMT
^^Hmm..... just a guess but try this: Control unit A5 (front / advance camera) Security Access 20103 Adaptation Select: " Zeichen Ende der Geschwindigkeitsbegrenzung" (mark the end of the speed limit)> set to "active" Don Just looked it up in the VCDS coding list and this seems to be the correct value. But there is a corresponding value to it, which has to be set to 00100111... But How?? And where can i find the value?? |
|
|
|
Post by dv52 (Australia) on Apr 14, 2017 23:23:01 GMT
^^Hmm..... just a guess but try this: Control unit A5 (front / advance camera) Security Access 20103 Adaptation Select: " Zeichen Ende der Geschwindigkeitsbegrenzung" (mark the end of the speed limit)> set to "active" Don Just looked it up in the VCDS coding list and this seems to be the correct value. But there is a corresponding value to it, which has to be set to 00100111... But How?? And where can i find the value?? marcel - it's just another adaptation channel in the A5 module. Here's the complete list of channels:
Activation speed for high beam assistant > 57 km/h
Body height left front wheel house edge > 670 mm
Body height left rear wheel house edge > 681 mm
Body height right front wheel house edge > 667 mm
Body height right rear wheel house edge > 681 mm
Calibration platform distance > 1500 mm
(1)-Calibration result-Static calibration; pitch angle > -58030537600.01 ?
(2)-Calibration result-Static calibration; yaw angle > 180218583348.76 ?
(3)-Calibration result-Static calibration; roll angle > -56751813128.11 ?
(4)-Calibration result-Static calibration; camera height > 1.06778e+012 mm
Direct. stab. assist speed threshold during towing mode > 300 km/h
Directional stab. assist.; intensity; power steering support > Medium
Directional stab. assist.; intensity; steering wheel vibration > Medium
Directional stabilization assist driver inact deactiv threshold > Medium
Display end of speed limit symbol > not activated
Display no passing allowed > activated
Display valid additional signs > 100111
Intervention moment > late (setting via menu)
Night vehicle detection activation brightness > 3 lx
Night vehicle detection deactivation brightness > 20 lx
Operating mode > vibration_on
Personalization of lane dept. warning Cl. 15 on > Last setting
Predictive route data run time > 0 ms
Road sign detection fusion mode > Road sign fusion
Speed threshold for high beam recommendation off > 27 km/h
Static calibration (end of assembly line) > 76 0F B4 0F 8C 0A 78 0A 6C 0A A4 0A A4 26 70 4A 18 17 64 26 70 32 E8 17 64 26 70 4A 18 0E 1C 26 70 32 E8 0E 1C
Windshield heat. direct. stabilize. assist. activation duration > 2 min
BAP_Personalisierung > not activated
CCP_interface > not activated
Country_Code_Signal_Consideration_Active > inputsignal_considered
Dev_Messages_EHR_deaktivation > Dev_Messages_not_activated
Dev_Messages_FDD_FLA_deaktivation > Dev_Messages_not_activated
Dev_Messages_HCA_deaktivation > Dev_Messages_not_activated
Dev_Messages_MOD_deaktivation > Dev_Messages_not_activated
Dev_Messages_VZE_deaktivation > Dev_Messages_not_activated
Dev_Messages_VZF_deaktivation > Dev_Messages_not_activated
Function_Module_Main_Beam_Assist > activated
Function_Module_Road_Sign_Recognition > activated
Hands_Off_Gong > Gong Typ 2
Hands_Off_Gong_Verzoegerung > 0.0 s
HCA_On_State > Menu
HCA_Warning_Intensity > Medium
Main_Beam_Assist_Urban_Area_Detection > On
Mask_error_reactions_for_development > not activated
(1)-Masked_fault_classes- > 255
(2)-Masked_fault_classes- > 255
(3)-Masked_fault_classes- > 255
(4)-Masked_fault_classes- > 255
Urban_Leaving_Velocity > 255 km/h
VZE_Prioritize_moisture > not activated
VZE_show_administrative_speed_limits > show_always
VZE_Show_valid_additional_signs > activated
VZE_Sorting_alternative_signs > 425
VZE_Sorting_valid_signs > 174
VZF_Country_Code > 0
VZMin_Attributierungs_Guete_Hauptverkehrszeichen > 0
VZMin_Attributierungs_Guete_Zusatzzeichen > 0
VZMin_Klassifizierungs_Guete_Hauptverkehrszeichen > 0
(1)-Windscreen_heater_for_lane_departure_warning_settings-par_Min_heating_time > 2 min
(2)-Windscreen_heater_for_lane_departure_warning_settings-par_Min_idle_time > 3 min
(3)-Windscreen_heater_for_lane_departure_warning_settings-par_Max_camera_temp > 85 ?C
(4)-Windscreen_heater_for_lane_departure_warning_settings-par_Max_activation_temp > 75 ?C
(5)-Windscreen_heater_for_lane_departure_warning_settings-par_Qualification_time > 0 s
(6)-Windscreen_heater_for_lane_departure_warning_settings-par_Init_heating_time > 4 min
(7)-Windscreen_heater_for_lane_departure_warning_settings-par_Low_threshhold_temp > -20 ?C
(8)-Windscreen_heater_for_lane_departure_warning_settings-par_High_threshhold_temp > 2 ?C
(9)-Windscreen_heater_for_lane_departure_warning_settings-par_Heater_Control_Power_Level > 9.0 W
So, just search for the channel name Display valid additional signs and enter the value (I suspect that it's already set to the correct value) Don |
|
|
|
Post by marcelsgti on Apr 15, 2017 14:33:20 GMT
Thanks!
Will test it today or tomorrow and then share a proper tutorial in OBD11 language :-)
Best regards,
Marcel
|
|
|
|
Post by marcelsgti on Apr 17, 2017 21:18:09 GMT
Information Control Unit (5F)
Adaption
Car_Function_List_BAP_Gen2
traffic_sign_recognition_0x21
Not activated -> Activate
Car_Function_Adaptions_Gen2
menu_display_road_sign_identification
Not activated -> Activate
menu_display_road_sign_identification_over_threshold_high
Not activated -> Activate
Front Sensors Driver Assistance System (A5)
Security access
Access Code 20103
Coding
Byte 1
Bit 0 Activate
Dashboard (17)
Coding
Byte 5
Bit 2 Activate
Front Sensors Driver Assistance System (A5)
Adaption
Display end of speed limit symbol
Not activated -> Activate
Display valid additional signs
Set value to 00100111
Works fine for me! But of course no guarantees ;-)
|
|
rolf
New Member
Posts: 4
|
Post by rolf on Jun 1, 2018 11:47:42 GMT
I have a MK7.5 R in the US (2018). The below code worked for me, however I get the "Limited function" warning sometimes. Also, my car thinks that the road signs are in KPH despite everything in my car being set to MPH. If anyone knows how to fix, please reply.
Information Control Unit (5F)
Adaption
Car_Function_List_BAP_Gen2
traffic_sign_recognition_0x21
Not activated -> Activate
Car_Function_Adaptions_Gen2
menu_display_road_sign_identification
Not activated -> Activate
menu_display_road_sign_identification_over_threshold_high
Not activated -> Activate
Front Sensors Driver Assistance System (A5)
Security access
Access Code 20103
Coding
Byte 1
Bit 0 Activate
Dashboard (17)
Coding
Byte 5
Bit 2 Activate
Front Sensors Driver Assistance System (A5)
Security Access 20103
Adaptation
Road Sign Detection fusion mode = road sign detection (default was road sign fusion)
Front Sensors Driver Assistance System (A5)
Long Coding
Byte 16
Bit 4 - Uncheck this box
|
|
|
|
Post by greg123 on Feb 13, 2019 22:21:59 GMT
Hi !
I have the same problem ! I don’t have “Select : channel numbers indicate end of speed limit” in the Adaptation to A5 unit control
I had search everywhere but nothing ...
do you have any solution for make it appears ?
Thank you !
|
|
|
|
Post by ofektal8 on Feb 14, 2019 10:31:24 GMT
Thats the coding I Followed to enable it, Give it A Shot
Traffic sign Assist:
Controller 5F (Information Electrical)
10 - Adaptations
Select channel: (63) Car_Function_List_BAP_Gen2-traffic_sign_recognition_0x21
Adjust Value to activated
Channel: (151) Car_Function_Adaptations_Gen2-menu_menu_display_road_sign_identification
Adjust Value to activated
Controller A5 (Front / front view camera)
07 - Coding
Byte 1
Bit 0 Enable - "01 traffic sign recognition (FTE) active"
Controller 17 (Instruments)
07 Coding
Byte 5
Bit 2 Enable - "Traffic Sign Recognition installed"
Controller 5F (Information Electr.)
07 - Coding
Byte 24 Bit 6 - tick Traffic Sign Display (VZA) active
Controller A5 (Front / front view camera)
07 - Coding
Byte 16
Bit 4 - tick this box (currently there are no descriptions for A5 longcoding)
|
|
|
|
Post by newty on Feb 14, 2019 10:49:34 GMT
Hi ! I have the same problem ! I don’t have “Select : channel numbers indicate end of speed limit” in the Adaptation to A5 unit control I had search everywhere but nothing ... do you have any solution for make it appears ? Thank you ! What is the part-no of your camera? A5-Cameras starting with 3Q0 are not having this adaption anymore. Just skip it. Please not that also Byte 0 Bit 1 enable is only applicable to 5Q0-Cameras. Enable 16/4 instead and leave 0/1 as it is. (Hint:3Q0 are sitting at the exact center of the car, while 5Q0 are slightly off next to the rain sensor). In the adaption, you might want to check "Road sign fusion mode" which shall be set to "Fusion" - but I never seen any other data from factory. |
|
|
|
Post by greg123 on Feb 14, 2019 18:30:21 GMT
Hi ! I have the same problem ! I don’t have “Select : channel numbers indicate end of speed limit” in the Adaptation to A5 unit control I had search everywhere but nothing ... do you have any solution for make it appears ? Thank you ! What is the part-no of your camera? A5-Cameras starting with 3Q0 are not having this adaption anymore. Just skip it. Please not that also Byte 0 Bit 1 enable is only applicable to 5Q0-Cameras. Enable 16/4 instead and leave 0/1 as it is. (Hint:3Q0 are sitting at the exact center of the car, while 5Q0 are slightly off next to the rain sensor). In the adaption, you might want to check "Road sign fusion mode" which shall be set to "Fusion" - but I never seen any other data from factory. Hi ! Thank you for your answer  The part-no of my camera is 3Q0980654H I had activate byte 16 bit 4, psd (in A5 and 5F) and I put fusion mode but that not working. I haven’t error message but no signs show in my display Have you another idea ? Do you know the good message bus in 5F -> adaptation -> BAP2 -> road sign 0x21 msg bus ? Thank you so much |
|
|
|
Post by greg123 on Feb 14, 2019 19:37:00 GMT
Thats the coding I Followed to enable it, Give it A Shot Traffic sign Assist: Controller 5F (Information Electrical) 10 - Adaptations Select channel: (63) Car_Function_List_BAP_Gen2-traffic_sign_recognition_0x21 Adjust Value to activated Channel: (151) Car_Function_Adaptations_Gen2-menu_menu_display_road_sign_identification Adjust Value to activated Controller A5 (Front / front view camera) 07 - Coding Byte 1 Bit 0 Enable - "01 traffic sign recognition (FTE) active" Controller 17 (Instruments) 07 Coding Byte 5 Bit 2 Enable - "Traffic Sign Recognition installed" Controller 5F (Information Electr.) 07 - Coding Byte 24 Bit 6 - tick Traffic Sign Display (VZA) active Controller A5 (Front / front view camera) 07 - Coding Byte 16 Bit 4 - tick this box (currently there are no descriptions for A5 longcoding)[/quote Thank you for your answer ! But don’t working for me ... |
|
|
|
Post by ofektal8 on Feb 14, 2019 21:40:37 GMT
Thats the coding I Followed to enable it, Give it A Shot Traffic sign Assist: Controller 5F (Information Electrical) 10 - Adaptations Select channel: (63) Car_Function_List_BAP_Gen2-traffic_sign_recognition_0x21 Adjust Value to activated Channel: (151) Car_Function_Adaptations_Gen2-menu_menu_display_road_sign_identification Adjust Value to activated Controller A5 (Front / front view camera) 07 - Coding Byte 1 Bit 0 Enable - "01 traffic sign recognition (FTE) active" Controller 17 (Instruments) 07 Coding Byte 5 Bit 2 Enable - "Traffic Sign Recognition installed" Controller 5F (Information Electr.) 07 - Coding Byte 24 Bit 6 - tick Traffic Sign Display (VZA) active Controller A5 (Front / front view camera) 07 - Coding Byte 16 Bit 4 - tick this box (currently there are no descriptions for A5 longcoding)[/quote Thank you for your answer ! But don’t working for me ... Thats Probably because what newty Said, my camera is 5Q0, and yours is the 3Q0. P.S Dont forget to enable sign assist in the car's menu. |
|
|
|
Post by greg123 on Feb 15, 2019 6:12:11 GMT
Thats Probably because what newty Said, my camera is 5Q0, and yours is the 3Q0. P.S Dont forget to enable sign assist in the car's menu. Yes I think too I have enable sign assist in the car’s menu but it don’t working I have update the satnav map but nothing ... there is a special update for sign assist ? And what is your msg bus in 5F -> adaptation -> BAP2 -> 0x21 msg bus sign assist ? Thank you 😊 |
|
|
|
Post by newty on Feb 15, 2019 7:55:34 GMT
Did you enable Predictive Routee Data in 5F (24/7)
Please check 17 (cluster) once again:
09/04 (Compass Display postion) enabled to be bottom
05/02 (Traffic Sign Rec.) enabled
And of course: Enable Traffic Sign display on the Infotainment in Driving Assistance.
Also, you can enable the traffic sign tab in the cluster customation found in car -> setup somewhere
Both display modes are independant, so please check and enable both
|
|
|
|
Post by greg123 on Feb 15, 2019 15:32:45 GMT
Did you enable Predictive Routee Data in 5F (24/7) Please check 17 (cluster) once again: 09/04 (Compass Display postion) enabled to be bottom 05/02 (Traffic Sign Rec.) enabled And of course: Enable Traffic Sign display on the Infotainment in Driving Assistance. Also, you can enable the traffic sign tab in the cluster customation found in car -> setup somewhere Both display modes are independant, so please check and enable both[/] Yes I had enable all that except “compass display position” so I go check that Thank you ! |
|
|
|
Post by greg123 on Feb 15, 2019 17:28:11 GMT
Did you enable Predictive Routee Data in 5F (24/7) Please check 17 (cluster) once again: 09/04 (Compass Display postion) enabled to be bottom 05/02 (Traffic Sign Rec.) enabled And of course: Enable Traffic Sign display on the Infotainment in Driving Assistance. Also, you can enable the traffic sign tab in the cluster customation found in car -> setup somewhere Both display modes are independant, so please check and enable both[/] Yes I had enable all that except “compass display position” so I go check that Thank you ! After check, Yes I had already enable “compass display position” No best result  Do you know the good message bus in 5F -> adaptation -> BAP2 -> road sign 0x21 msg bus ? Read more: forum.obdeleven.com/thread/1576/traffic-sign-recognition-problem#ixzz5fcc0GS91 |
|
|
|
Post by schniefelus on Nov 6, 2020 7:34:24 GMT
Hello, I have a Golf 7 BY 2016 (so not the facelift version). I have coded TSR using this instruction: forum.obdeleven.com/thread/167/golf-mk7-coding-adaptationsTSR seems to work as it should but I get an intermittent error "Databus error value received" with fault code U112300. It seems the error occurs when I start the car because the speed is at 0.00 km/h. Does someone have the same problem? How can I fix this? I am pretty sure I didn't miss a setting, I compared many instructions of Golf 7 (pre face lift) and all seem to be the same. Infos about the car: I have the dynamic light assist, HW of the camera is 5Q0980653, SW is 5Q0980653G I attached the full backup of the control units. Attachments:full coding.txt (453.93 KB)
|
|
|
|
Post by excalepar61 on May 18, 2021 4:47:18 GMT
Hi
I can not find 5F (Information Electrical)
|
|
Do you know the good message bus in 5F -> adaptation -> BAP2 -> road sign 0x21 msg bus ?