|
|
Post by ninjageezer on Mar 8, 2017 23:58:41 GMT
Can the OBDeleven do the dsg reset like the VCDS can ? MY17 golf R
|
|
|
|
Post by ninjageezer on Mar 10, 2017 20:12:48 GMT
I guess not then  |
|
|
|
Post by ninjageezer on Mar 10, 2017 20:40:53 GMT
I guess not then |
|
|
|
Post by dv52 (Australia) on Mar 11, 2017 3:31:56 GMT
I guess not then Don't see why OBD11 wouldn't do the procedures, but I've not done it myself.
Here are the VCDS instructions with translations to OBD11 where needed - Again, I've not done this procedure- so entirely untested!!
Don
Section 1: DSG Prerequisites:
Transmission fluid temperature between 30°C - 100°C. You can confirm these temperatures as follows:
- Select Automatic Transmission module @ address hex02
- Select Live Data
- Select Control Module temperature and Clutch temperature air / splash oil
Section 2: In-cabin Prerequisites
Make sure that:
- Selector lever is in Park
- Engine is at idle speed - do not press accelerator pedal during this procedure!!
- Parking brake and foot brake MUST be applied during the entire procedure. This can be confirmed by viewing Live Data values:
* Brake Light Switch
* Brake test switch
Section 3: Basic Settings Procedure:- Select Automatic Transmission module @ address hex02
- Select Basic settings
- Select Basic settings of transmission
- Set to Active and press Tick to start procedure
Notes - Basic Setting Procedure: - During the basic setting procedure, there may be loud gear shifting noises from the transmission, this is normal.
- Basic setting procedure may not complete successfully if:
- The transmission fluid temperature gets too hot.
- Hand Brake is released
- Foot brake is released
- Engine RPM is increased
[li]Once procedure is complete, - Basic Settings should report Finished Correctly and there should be an indication of this in the Status of Basic Settings in Live Data section
- Check for fault codes in the Automatic Transmission module -if Intermittent fault codes are stored - they should be cleared
[/li][/ul]
|
|
|
|
Post by Guesty on Mar 11, 2017 9:24:36 GMT
What's the purpose of this coding
|
|
|
|
Post by ninjageezer on Mar 12, 2017 22:32:46 GMT
resets all the settings for the dsg gearbox
|
|
|
|
Post by 2nr4lyf on Mar 12, 2017 22:56:58 GMT
There is no resetting the 16+ dsg. It has constant adaptive learning (according to local vw tech)
|
|
|
|
Post by dv52 (Australia) on Mar 13, 2017 12:39:32 GMT
^^^^ Yes, but the starting point for the adaptive learning process has to be somewhere - when the car rolls off the production line, there must be a predetermined set of engine revs/torque settings/ transmission oil temperatures that the DSG uses which are then modified for driver behaviour. I had thought that this was the point of the DSG resetting process - to take the transmission gear change curve back to the factory settings (perhaps?)
Don
|
|
jacko
Junior Member
Posts: 64 
|
Post by jacko on Mar 14, 2017 22:36:51 GMT
^^^^ Yes, but the starting point for the adaptive learning process has to be somewhere - when the car rolls off the production line, there must be a predetermined set of engine revs/torque settings/ transmission oil temperatures that the DSG uses which are then modified for driver behaviour. I had thought that this was the point of the DSG resetting process - to take the transmission gear change curve back to the factory settings (perhaps?) Don Can be this reset-procedure solution for an error P173400? The error below back even ignition on, but I don't feel any technical problem with transmission unit. 02 Transmission Control Module
System description: DQ250-6F MQB
Software number: 0D9300040A
Software version: 3613
Hardware number: 02E927770AN
Hardware version: H52
Serial number: TFK01304121529?
ODX name: EV_TCMDQ250021
ODX version: 001001
Long coding: 0014
Trouble codes:
P173400 - Starter release from the selector lever sensor system
Intermittent
|
|
|
|
Post by dv52 (Australia) on Mar 14, 2017 23:26:59 GMT
Jacko: No. i don't believe that this would work on your problem
|
|
|
|
Post by lebenfitti on Mar 15, 2017 16:39:17 GMT
Has anyone tried this? Is there a down side to attempting this?
|
|
|
|
Post by ninjageezer on May 25, 2017 19:17:54 GMT
^^^^ Yes, but the starting point for the adaptive learning process has to be somewhere - when the car rolls off the production line, there must be a predetermined set of engine revs/torque settings/ transmission oil temperatures that the DSG uses which are then modified for driver behaviour. I had thought that this was the point of the DSG resetting process - to take the transmission gear change curve back to the factory settings (perhaps?) Don Can be this reset-procedure solution for an error P173400? The error below back even ignition on, but I don't feel any technical problem with transmission unit. 02 Transmission Control Module
System description: DQ250-6F MQB
Software number: 0D9300040A
Software version: 3613
Hardware number: 02E927770AN
Hardware version: H52
Serial number: TFK01304121529?
ODX name: EV_TCMDQ250021
ODX version: 001001
Long coding: 0014
Trouble codes:
P173400 - Starter release from the selector lever sensor system
Intermittent
I have seen the same error on the 3 golfs ive scanned inc mine i think its normal .  |
|
|
|
Post by Westindies on Sept 15, 2017 16:31:35 GMT
Hello,i've been trying this procedure on a Q3 STronic and still getting error message 13 not executable,message too long etc..
Anyone tested this procedure on OBDeleven?
|
|
|
|
Post by kieran on Oct 27, 2017 11:26:33 GMT
I've been trying to do this and I get the error "(13) Function cannot be performed, mess. length or format incorrect" does anyone have any idea what I could be doing wrong?
|
|
|
|
Post by 2nr4lyf on Nov 5, 2017 12:32:47 GMT
There's a app, done it but doesn't change anything. Still drives the exact same afterwards.
|
|
|
|
Post by sjones182 on Feb 10, 2018 23:55:28 GMT
I am able to use the app for the dsg reset, but when I try to do basic settings to calibrate the synchros and other tolerances I can't get it to work always says error message too long. Can someone please help me to get the basic settings to work!
|
|
|
|
Post by gwileman on Feb 12, 2018 16:25:33 GMT
Can anyone confirm that this worked?
|
|
|
|
Post by blitz869 on Mar 1, 2018 14:28:56 GMT
Can anyone confirm that this worked? I can confirm it works, 2016 Golf R Canadian model. It was kind of making a slight clunk sound coming to a stop (around 14km/h) it seems to have smoothed out. There’s another procedure for resetting the clutch pack? Can anyone walk me through that? |
|
|
|
Post by importhotshot on May 18, 2018 21:09:03 GMT
Will this procedure work for an 07 passat with an 09G transmission? Had shift kit installed for maintenance reasons and need to reset trans to solve shifting issues.
|
|
|
|
Post by obduser on Jun 26, 2018 12:38:53 GMT
|
|
|
|
Post by spielwurfel on Jul 11, 2018 13:18:43 GMT
I haven't done the reset procedure using OBD11, but I've done on a third party workshop which happens to have the official VW electronic tool. DSG did some noises and etc. but I didn't feel absolutely no change to it's behavior. I did it because I though my DSG wasn't working too properly, but at the end I concluded it was only my impression... Probably the resetting will do something useful if you really have a problem with your DSG, which wasn't my case.
|
|
|
|
Post by spielwurfel on Sept 20, 2018 21:23:03 GMT
I've been trying to do this and I get the error "(13) Function cannot be performed, mess. length or format incorrect" does anyone have any idea what I could be doing wrong? I'm getting the same error as you... Does someone know why this is happening? |
|
|
|
Post by tautvydasv on Nov 22, 2018 14:09:43 GMT
I've been trying to do this and I get the error "(13) Function cannot be performed, mess. length or format incorrect" does anyone have any idea what I could be doing wrong? I'm getting the same error as you... Does someone know why this is happening? I also get the same error. 2015 GOLF R |
|
|
|
Post by panman on May 29, 2019 19:02:12 GMT
I'm getting the same error as you... Does someone know why this is happening? I also get the same error. 2015 GOLF R Any resolution to this bug? I just bought my OBDeleven last Monday and am encountering this problem left and right. Every transmission adaptation and basic setting actions I tried to perform resulted in this "(13) Function cannot be performed, mess. length or format incorrect" error. I have not tried to do adaptations or basic settings with other control units. I am aware of the transmission reset ONE-CLICK-APP, but it does not replace the other adaptation and basic setting functions. Any information or workaround is appreciated. North America 2015 Golf Sportwagen S TDI (EA288) with DSG (DQ250). OBDeleven app version 0.12.1, on Android 4.4.2, LG G2. Incidentally, the transmission reset ONE-CLICK-APP caused my DSG to be stuck in reverse immediately after the reset, for shifter positions D and S in addition to R. Luckily an engine shutdown and restart got it back to normal. If this is the expected behavior, it really should be documented in the ONE-CLICK-APP's description. If it's not the normal behavior, then there is either a bug in the ONE-CLICK-APP, or my DSG has gremlins. Again, thanks for the help. |
|
bagy
New Member
Posts: 4
|
Post by bagy on Sept 9, 2019 19:45:46 GMT
Hi everyone. I also have the same issue with the DSG Adaptation. Will there be a bugfix related to this problem? And also, i cannot find this one-click-app for DSG Basic Settings. Is this under "Garage -> Car -> Apps"? Because i dont see anything  Thanks |
|
|
|
Post by jrbendicho on Nov 21, 2019 2:48:45 GMT
Hi I'm having the same issue, trying to reset the adaptation values on my 2016 Audi a6 3.0T. has developed a rough downshift from 3-2 when coming to a stop. using obdeleven transmission - basic settings - reset all adaptation values and i get (13) Function can not be performed, mess. length or format incorrect. i noticed my software version for the transmission is 1002 and it says there is an update 1005, may that be the case, if soo how can update the software, can i use obdelven to do that.
btw how do i know if a have a s-tronic or tiptonic, im not quite sure wich one i have, any clue on how to find that out
thanks.
|
|
|
|
Post by giovanni on Dec 8, 2019 18:43:39 GMT
^^^^ Yes, but the starting point for the adaptive learning process has to be somewhere - when the car rolls off the production line, there must be a predetermined set of engine revs/torque settings/ transmission oil temperatures that the DSG uses which are then modified for driver behaviour. I had thought that this was the point of the DSG resetting process - to take the transmission gear change curve back to the factory settings (perhaps?) Don Can be this reset-procedure solution for an error P173400? The error below back even ignition on, but I don't feel any technical problem with transmission unit. 02 Transmission Control Module
System description: DQ250-6F MQB
Software number: 0D9300040A
Software version: 3613
Hardware number: 02E927770AN
Hardware version: H52
Serial number: TFK01304121529?
ODX name: EV_TCMDQ250021
ODX version: 001001
Long coding: 0014
Trouble codes:
P173400 - Starter release from the selector lever sensor system
Intermittent
|
|
|
|
Post by giovanni on Dec 8, 2019 18:47:29 GMT
Scusate l'intrusione io ho una golf 7 1.6 tdi non ho alcun problema al cambio dsg dq200 doppia frizione a secco, ma vorrei modificare alcuni parametri quali aumentare la coppia, attivare il launc control ecc qualcuno mi può aiutare
|
|
|
|
Post by tigeo on Sept 22, 2020 16:32:47 GMT
Let's revive this, same issues. I can use the app to to the basic settings no issue, but I can't use any of the other basic settings and was interested in the "start double clutch fast adaptation" one - I get "(13) Function cannot be performed, mess. length or format incorrect".
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Sept 22, 2020 16:59:45 GMT
I have tried several times using both Android and IOS but my Cupra 280 DSG Box just comes up with an error (Not available).
When I raised it with Support (not that that means anything) they said it was a know bug.....
|
|
