|
|
Post by chrisdraggers3 on Sept 25, 2021 10:26:02 GMT
2016 Audi RS3 sportback rear LED turn signals not functioning properly. The outer turn signals operate normal. The left inner turn signal on tail gate does not work. The right turn signal on tail gate does not work but when the headlights are on, it turns on but does not flash.
Scanned vehicle..central electric ..module incorrectly coded. Is this error related to the issue and is there a code to fix this
|
|
|
|
Post by chrisdraggers3 on Sept 25, 2021 10:49:26 GMT
The fault code
OBDeleven vehicle history log
Date: 2021-09-25 05:48:01
VIN:
Car: Audi RS3
Year: 2016
Body type: Sportback
Engine: CZGB 270 kW (367 hp) 2.5l
Mileage: 36935 km
---------------------------------------------------------------
09 Central Electrics
System description: BCM MQBAB H
Software number: 5Q0937084CL
Software version: 0175
Hardware number: 5Q0937084AN
Hardware version: H24
Serial number: 01061616100318
Faults:
U101400 - Control module incorrectly coded
static
Priority - 2
Malfunction frequency counter - 1
Unlearning counter - 12
km-Mileage - 36871 km
Terminal 15 status - On
Terminal 50 status - Off
Voltage - 12.1 V
Outside air temperature - 31.5 °C
Status Bremslichtschalter (HW) - Off
Status Bremslichtschalter (CAN) - Off
Off - operated
Parking light - not activated
Automatic high beam assist - not activated
Low beam - not activated
Parking light left - not activated
Parking light right - not activated
Letzte Weckursache/ Werte [00;2E] - keine Störschutzursache
CAN-Bus aktiv - On
date - 2021-09-23 17:21:59
|
|
|
|
Post by chrispat19893 on Oct 13, 2021 12:24:28 GMT
Have you made any changes to the coding prior to this issue arising? Take a look under the history tab in the control module and see what it says.
|
|
gors
New Member
Posts: 3
|
Post by gors on Sept 16, 2023 23:10:01 GMT
Hi, I have the same issue. Bought a RS3 8V and the rear turn signals where both not blinking. I did something with coding about pace blink and fixed the inside blinkers but outside doesnt flash. Same error and no back ups. Did u find a solution?
|
|
|
|
Post by dv52 (Australia) on Sept 17, 2023 21:20:21 GMT
gors Hi. hmm......... it's 2 x years since the previous post!! Post-up screenshots of Leuchte18BLK HLA6. To be clear, I need to see ALL 19 x channel values in your screenshots
Don
|
|
gors
New Member
Posts: 3
|
Post by gors on Sept 19, 2023 7:59:58 GMT
  Hi don! Thanks for youre fast reply. Hereby my screenshots, hopefully u can help me! Thanks in advance! |
|
|
|
Post by weldlyfe88 on Sept 19, 2023 20:46:21 GMT
Check the wiring, specifically the hinge on the left side of the trunk lid, the wiring follows the hinge there. Over the course of time from opening and closing the trunk the wires effectively shear themselves.. ask me how I know.
|
|
|
|
Post by dv52 (Australia) on Sept 19, 2023 20:46:33 GMT
gors: hmm......... very odd leuchte-programming for a rear turn signal lamp!!
To fix - do this: Leuchte18BLK HLA60 - Lichtfunktion A 18 > Blinken links Hellphase
- Dimmwert AB 18 > 127
Leuchte19BLK HRC31 - Lichtfunktion A 19 > Blinken rechts Hellphase
- Dimmwert AB 19 > 127
Don
|
|
gors
New Member
Posts: 3
|
Post by gors on Sept 21, 2023 20:03:17 GMT
dv52 (Australia) you my man, are a f***ing hero!!! Thanks a lot and much love! Appreciate it.
|
|
