|
|
Post by zedocoding on Oct 23, 2023 2:14:22 GMT
11A035710 Broadband loudspeaker The other is no longer in production.
The 10A035710 is the harman kardon woofer for id3 rear, full range. 2ohm 50w, large coil. I instaled it on my id3. understand. - With the Harman Kardon system 2. The front woofers have 4 wires going to them - why? Because hk front woofer have double coil. A very good speaker. Here's the 6 speaker system  Where is connected the center speaker on the dash? I'm thinking disconnect it size I have focal on front. ___/_/_________ Other thing, 1clickapp for rear speakers retrofit set the topology to 19. In my case I feel lack of front bass and excessive bass on rear . 😐 |
|
ID.3
Full Member
Posts: 210
|
Post by ID.3 on Oct 23, 2023 17:33:38 GMT
I don't know where the central speaker is plugged in, but you should leave it as it is, it's normally the one that will give you an alert in the event of a crash, but check? If you don't want to have it any more, just disconnect it directly at the bottom of the speaker.
If not, you need to follow the wires to see if it's connected in parallel to the other front speakers?
As for the type of signal, you can leave it as it is, personally I don't hear any difference.
|
|
|
|
Post by seiger on Oct 31, 2023 19:53:22 GMT
Hi ,
to activate the fader screen and related DSP settings, in addition to highlighting channels 1 and 4, it is necessary to set the topology flow parameter, in id3 it should basically be at 16, it should be set at 19, I have a Born, it was at 17 I tried all the values from 18 to 21, the rear speakers are activated but the center channel and the fader/dsp settings have disappeared
|
|
papad
New Member
Posts: 13
|
Post by papad on Nov 20, 2023 20:41:49 GMT
There seems to be a 1-click app now under retrofits for this, 50 credits I used the 1-click app, worked perfect for me. Also, since you need to connect JTP(junior timer power)-crimp pins in the socket, the pins are paired 1+,5- and 4+,8- for the two speakers. If you look closely into the connector of the infotainment unit, the numbers are seen for the two missing pair connectors. In the schematic here these numbers are missing/faulty. |
|
|
|
Post by tghazi on Jan 20, 2024 23:27:50 GMT
Hi guys
Please where can I fin signal flow topology in OBDeleven
I searched for it in 5f module but I didn't find it
|
|
|
|
Post by bornv2 on Jun 1, 2024 17:45:34 GMT
Hi All
I'm about to attempt this on my Cupra Born, I'm just waiting on the looms to be delivered.
Has anyone managed to progress this with the Cupra Born so that the fader works, my initial investigation says it's possible but I wonder if they are creating a custom dataset for 8125 based on some work carried out that isolates the Seat products as being the only setup with the standard 5 channels.
I'm interested to find anyone that has the ability to channel map all the adaptations on 8125 after having a kufatec coding done, the topolgy for those still looks like its set to 15 which is confusing.
Anyway I'm keen to get this work for the Cupra Born people :-)
Cheers
Scott
|
|
|
|
Post by thesaladcrouton on Aug 1, 2024 1:28:27 GMT
Sorry for the late reply. Finally it has been resolved. I went back to the installer and connected the speakers (front + rear) without the amp. Everything worked fine. Connected the speakers via an Axton 452dsp amp with a resistor piece on the cable. Bam - everything worked! So either it was an issue with the Focal amp or it was the resistor causing the issues with the parking sensors. Although this process caused some time and effort, the result was very satisfying! Thanks for all your help on figuring out the issues. Hey there! I wanted to try and get a bit more info on your resolution. I have the exact same issue. Recently installed the Focal impulse amp in my VW Caddy and now none of the parking sensors are working. Did you end up getting it resolved with the focal amp? If is, could you detail the fix or resolution for me? Any help would be greatly appreciated! |
|
