|
|
Post by stickitdecals on Feb 8, 2017 1:51:36 GMT
So apparently I've screwed something up to where my headlights don't work when I turn the wheel while driving. Also, the side markers in my headlights that come on when I turn at low speed isn't working.
It started when I changed from nar to ese. Got a warning of an adaptive fault and switched back.
How do I fix what I screwed up?
Also, I'm in USA.
|
|
|
|
Post by Random guest on Feb 8, 2017 15:43:45 GMT
So apparently I've screwed something up to where my headlights don't work when I turn the wheel while driving. Also, the side markers in my headlights that come on when I turn at low speed isn't working. It started when I changed from nar to ese. Got a warning of an adaptive fault and switched back. How do I fix what I screwed up? Also, I'm in USA. TO FIX HEADLIGHT ISSUE: Hi! i executed the procedure described above: Headlight Adjustment [Select] [55 - Xenon Range] [Basic Settings - 04] Select Basic headlamp setting from the drop-down menu. [Go!] to activate the Basic Setting. The meas. block field will show Running. Adjust the headlights using their manual adjusting screws as referenced against a suitable aiming target. [Stop] after any needed mechanical adjustments are completed. Select Acknowledge basic setting [Go!] to activate the Basic Setting. After the result of Finished Correctly appears click [Stop] The adjustment should now be learned. [Done, Go Back] Don't forget to check/clear fault codes afterwards. [Close Controller, Go Back - 06] |
|
2017gti
New Member
2017 PURE WHITE GTI AUTOBAHN, DCC
Posts: 6 
|
Post by 2017gti on Mar 10, 2017 4:28:07 GMT
Check settings in the car...
The prior answer was referring to height adjustment not side to side i think.
|
|
|
|
Post by njdsina on Mar 17, 2017 23:41:14 GMT
Same boat, reset and applied basic setting which removed the error, but no more cornering light or rotating headlights. Adaptive lighting is also checked in the car menu. Any further help would be appreciated it anyone was able to resolve it.
|
|
Anthony anthony anthony
Guest
|
Post by Anthony anthony anthony on Mar 18, 2017 0:15:13 GMT
Have you not got a log history of what you had changed? Go back through a reset everything recent.
If you show me the menu you have adjust I can print screen mine. I'm in UK
|
|
a777
New Member
Posts: 3
|
Post by a777 on Dec 20, 2017 18:25:57 GMT
I am having same problem, put rain sensor on headlights then got fault Adaptive Light
Failure removed rain sensor still have fault.
In module 55 when I go into fault it comes up no basic setting
I don't do long code is there anyway to get basic settings set without long code?
Thanks
|
|
|
|
Post by dv52 (Australia) on Dec 21, 2017 20:25:55 GMT
^^^ try the basic setting procedure on the 2nd post above
Don
|
|
|
|
Post by stickitdecals on Jan 9, 2018 20:07:20 GMT
Did the above and it worked perfectly. Forgot to respond, but wanted to let others know that it does work.
|
|
|
|
Post by mk7gtiguy on May 22, 2018 14:01:25 GMT
Do I need to do this if I lower the car?
|
|
|
|
Post by dv52 (Australia) on May 23, 2018 6:08:39 GMT
Do I need to do this if I lower the car? mk7gtiguy: Yes - unless your lowering exercise has been ridiculously accurate on all 4 wheels!!
Don
|
|
|
|
Post by kzolt79 on Apr 15, 2021 13:40:07 GMT
Hi!
The car is Octavia 2016 with adaptive xenon. But after I click on Go (marked with blue), it automatically stops after a few seconds. I don't have time to adjust and to click on stop after that (part marked with red).
I tought that I click go, don't wait to stop automatically, but I click on stop after a few seconds, then adjust the headlights and then do the part marked with green? Do you think it's OK like that? Or any suggestions?
Thx.
Headlight Adjustment
[Select]
[55 - Xenon Range]
[Basic Settings - 04]
Select Basic headlamp setting from the drop-down menu.
[Go!] to activate the Basic Setting.
The meas. block field will show Running.
Adjust the headlights using their manual adjusting screws as referenced against a suitable aiming target.
[Stop] after any needed mechanical adjustments are completed.
Select Acknowledge basic setting
[Go!] to activate the Basic Setting.
After the result of Finished Correctly appears click [Stop]
The adjustment should now be learned.
[Done, Go Back]
Don't forget to check/clear fault codes afterwards.
[Close Controller, Go Back - 06]
|
|
