tom
Closed beta tester
Posts: 1 
|
Post by tom on Jan 18, 2016 20:57:58 GMT
How can I set activation of the CCS to on? I've installed the cruise control wiring and stalk I just need to tell my Golf that it's there.
Any help would be appreciated. Thanks.
|
|
|
|
Post by OBDeleven on Jan 19, 2016 7:28:32 GMT
Hi,
Just go to your engine control unit and enter security access 11463 to enable CCS or 16167 to disable it.
|
|
jag
New Member
Posts: 3
|
Post by jag on Jun 19, 2017 11:44:40 GMT
I have tried this and get an error that the security access codes are invalid. It then locks me out. Any suggestions?
|
|
|
|
Post by Theoldboy on Jun 20, 2017 22:13:48 GMT
According to this video you have to go to engine control unit (01) then take login 11 and there you enter the 11463 or 16167.
Afraid i don't have this car so do not know what login 11 equals in obd11
|
|
|
|
Post by markan on Sept 30, 2019 14:17:34 GMT
I can’t even find CCS anywhere under control units and engine why ? Is it because I am using OBD 11 but not PRO?
|
|
|
|
Post by iangil on Jun 30, 2022 15:30:49 GMT
Sorry to resurrect an old thread but I have the same question and I'm wary off bricking the ecu if I do something wrong.
I have a 2002 Mk4 2.0ltr Gti (HL) with the AZJ engine and am waiting for my genuine VW controls and loom to arrive. I've never long coded anything and there doesn't seem to be any short way to enable this function using credits although I have Pro status and 100+ credits to play with.
All the instructions seem to show VagCom in some form although the version I found seems to contradict the above post as follows:
" For the latter the following is the 'generic' procedure for carrying out this enabling work:
Select engine control module by pressing "01Q".
Select read data function by pressing "08Q".
Read group 06 by pressing "06Q" or "006Q" depending on which version of VAG 1551 tool that you have.
The 1551 will display a bunch of numbers. The fourth group of numbers, on the far right of the display will be either "0" or "255". "0" means that cruise control is already enabled. If you see "255" then cruise control is locked, unlock it using the following steps.
Press the right arrow key.
For login procedure press "11Q".
Enter the unlock code "11463Q".
Now repeat the above steps and see if that "255" has changed to a "0".
When you switch the cruise control 'on' with the new stalk switch, and the ignition is 'on', the symbol should alight in the speedo.
Turn the iginition 'off', remove the key, then proceed as normal to drive the car.
Ensuring you have a clear open stretch of road, test the controls.
You must have the stalk switch in the 'on' position for it to work.
CHECK THE CRUISE CONTROL DISENGAGES WHEN THE BRAKE OR CLUTCH IS PRESSED (be ready to knock it out of gear when testing the clutch switch!)"
It would be much appreciated if someone in the know could take pity on a newb and break this down into something easy to follow on OBD11 as I'm sure I'm not the only planning this
|
|
|
|
Post by iangil on Jul 14, 2022 20:13:56 GMT
Ok,sorry,it really was that easy:
Engine Module - it gave me a choice of two codes,one of which was 11463 so just input that and ticked the box and voila . Job done.
|
|
|
|
Post by radders567 on Nov 27, 2022 15:37:17 GMT
Hi, i keep trying to put the code 11463 into the security access box and all the car says is "not enough time has passed" and does not let me do anything.
Any ideas?
|
|
