|
|
Post by daftmonkey on May 16, 2021 23:27:13 GMT
Hey i'm trying to do the below but am getting stuck With car lifted off the ground Enter Control Module 14- Adaptive Suspension Go to Adaptations Select “Adapting with deflected wheels” Take note of the values, as they should change later. Slide the green arrow to the right to write Enter security code 20103. It should say success. - screen just flashes and returns to "enter security code"
*Stuck*Don’t change any values, instead back out Enter Basic Settings Select “Adapting with deflected wheels” Slide to Start. It should run for a second and then say something like basic setting ended. Am i using the the wrong security code? has it changed between mk7 and mk7.5? does anyone know what it might be? someone leave their car in a garage hooked up to a battery charger for 8 hours to do a security code scren for me  or does this procedure just not work on mk7.5's at all? Thanks |
|
|
|
Post by jamstonmartames on Sept 5, 2021 9:50:52 GMT
Hey
Did you get this fixed?
I hear that you need ignition on, engine off, bonnet up. I'm about to embark on DCC retrofit shortly.
Preferably using ODIS or OBD. VCDS isn't plain sailing with this calibration.
Thanks
James
|
|
|
|
Post by dark5had0w on Sept 15, 2021 6:30:14 GMT
i did DCC re-calibration successfully on my Superb, with the following steps:-
Go to Control Module 14 - Adaptive Suspension
Enter security code 20103.
Go to Adaptations
Select “Adapting with deflected wheels”
Take note of the values, as they should change later.
Don’t change anything, instead back out.
Enter Basic Settings
Select “Adapting with deflected wheels”
Slide to Start or Press & hold Green tick to Start.
It should run for a second and then say something like basic setting ended.
That’s it, you’re done. Double check adaptations to make sure the values have changed and saved.
|
|
|
|
Post by ycymro on Sept 27, 2021 12:37:49 GMT
What’s the purpose of recalibration? Is it needed only if DCC is retrofitted, or is it periodically needed on cars with OEM DCC?
|
|
|
|
Post by dark5had0w on Sept 29, 2021 4:40:35 GMT
It's recommended to do if the car has been lowered with shorter springs.
|
|
|
|
Post by ycymro on Sept 29, 2021 23:11:57 GMT
Thanks
|
|
|
|
Post by daftmonkey on Nov 7, 2021 17:52:34 GMT
did you do this whilst he car was off the ground?
i ended up giving up on it since i this forum/post wasn't as activeas i hoped it would be, but would be interested to try again! once someone else gives it a crack and confirms it works!
|
|
|
|
Post by dblhelix on Nov 28, 2021 1:49:27 GMT
It's recommended to do if the car has been lowered with shorter springs. Curious how this would have any impact of done on a lift with wheels fully dropped. How would the module know you are lowered? Same droop if lowered or not. |
|
|
|
Post by dark5had0w on Jan 12, 2022 0:57:41 GMT
incorrect - when the car is lowered, it has shorter springs, hence the drop is less compared to the factory springs.
|
|
|
|
Post by koldico on Sept 11, 2023 11:22:43 GMT
Hello everyone, I just installed some blistein b16damptronic, would it be necessary to do the basic adjustment of the dcc?
|
|
|
|
Post by koldico on Sept 15, 2023 2:45:40 GMT
I have done it with the ignition on, front hood open without handbrake and in position N of the gearbox, it may be that it should be in P and the handbrake applied
|
|
|
|
Post by koldico on Sept 15, 2023 15:42:26 GMT
Nothing has been possible, I have put it in P and I have put on the handbrake, with the android tablet with the android mobile and nothing has come up, I enter the security code and it picks up 20103 without problems, I go to Adaptation and Asking me again goes into a loop and there is no way to continue
|
|
|
|
Post by koldico on Sept 16, 2023 9:27:30 GMT
I have found this other way.
Looking at the service manual, it talks about performing
a Basic Setting "DCC" is reset when something in the
The suspension is changed (ball joint, springs, etc.).
The basic configuration screen for the DCC module has three
options
Adaptation with offset wheels
* Reset control module delivery status
maker
* Restore vehicle specific data
Does anyone know what these three options do? And what
Does it correspond to performing a dcc reset?
The VCDS forums state that you have to lift the car in the air (so that
suspension is in full droop), then perform a DCC
Reset basic settings.
Address 14: Susp. Elect. (J250) Login: 31564, Basic
Settings: Channel: 1 On/Off
I hope it works
|
|
|
|
Post by arandax on Sept 29, 2023 19:04:26 GMT
I've done it on my S3 8Y at dealer.
It's a day / night difference.
I wasn't able to do it with OBD11, but for sure there are 2 steps:
1. car lifted (no wheels touching the floor) first basic setting;
2. car onto the ground, second setting.
hope it helps
|
|
or does this procedure just not work on mk7.5's at all?
