|
|
Post by selin46 on Mar 10, 2021 8:15:30 GMT
Hi everybody,
Looking for anybody that successfully lowered their C8 with OBDeleven. My previous C7 was no problem but heard the newer platforms were different from a Audi mechanic. Any inputs?
Thanks
|
|
enry68
Junior Member
Posts: 54
|
Post by enry68 on Mar 25, 2021 16:42:47 GMT
Hello, if I'm not in mistake, the C8 has Magnetic Suspension, so if true the coding may be different.
Enrico
|
|
|
|
Post by svre46 on Mar 26, 2021 17:37:22 GMT
Hi everybody, Looking for anybody that successfully lowered their C8 with OBDeleven. My previous C7 was no problem but heard the newer platforms were different from a Audi mechanic. Any inputs? Thanks I think the issue is getting the security access code for module based on my VCDS experience. ODIS is the only way I have heard thus far. |
|
bzqq7
New Member
Posts: 3
|
Post by bzqq7 on Jul 24, 2022 11:32:04 GMT
Hi
Is something new for lowering car?
Any codes?
Best Regards
Bz
|
|
|
|
Post by dezurita07 on Jul 31, 2022 14:53:41 GMT
Would love a resolution for this as well. 2022 s6 and can’t adjust the ride hight on the car…
|
|
|
|
Post by dkajfes on Aug 29, 2022 1:58:22 GMT
There should be a setting to enable it. I have an S6 in Australia and i can adjust height in the drive mode screen. Suspension should allow for it provided its the same world wide. I do have the adaptive air suspension fitted to my vehicle.
|
|
|
|
Post by darkqueen55tfsi on Sept 16, 2022 23:27:09 GMT
Switch on ignition - Drive Select -AUTO
Open engine hood
Control unit 74 Chassis control
Read out adjustment values
Body height of front left wheel arch edge
Body height of front right wheel arch edge
Body height of rear left wheel arch edge
Body height of rear right wheel house edge
Basic setting
Activate level control
Approach reference level
Adjustment Enter new values
Body height of front left wheel arch edge (value old plus x)
Body height, wheel housing edge, front right (value old plus x)
Body height of rear left wheel housing edge (value old plus x)
Body height of rear right wheel arch edge (value old plus x)
Basic setting
Switch to normal level control function
Activate level control
Clear fault memory
|
|
dejan
New Member
Posts: 1
|
Post by dejan on Oct 11, 2022 11:32:07 GMT
Dear, I follow your step and read out values, but in next step under the Basic setting -Activate level control can't set to active it says only not active and not allowed to be changed and second window lower it say only config1 and that is only option. Normally without this step I can not input new values because it say that procedure is not correct. Can it be some car restriction or else. Any suggestion...
Thank you
|
|
bzqq7
New Member
Posts: 3
|
Post by bzqq7 on Dec 19, 2022 17:41:12 GMT
Open front hood/leave car in AUTO
1.ADAPTATION
read high of all 4 wheels
2.BASIC settings/Activate level control
3.BASIC settings/Set reference level
- - - - beep fault system- - - -
4.ADAPATION /put new hights(higher than factory)
5.BASIC settings/switch to normal level function
6.BASIC settings/ Activate level control
7. clear faults
Best
Blaz
|
|
|
|
Post by avant2413 on Dec 21, 2022 21:25:00 GMT
FYI “BASIC settings/Set reference level” isn’t an option in OBDeleven at least on my rs6.
|
|
bzqq7
New Member
Posts: 3
|
Post by bzqq7 on Dec 23, 2022 15:01:49 GMT
or start up reference level control
|
|
|
|
Post by rxmxsh on Dec 24, 2022 1:04:28 GMT
New guy here as well. I played around with this on my 21 RS6. Ran into some issues and tried roll back to stock. I was mostly successful but now the suspension doesn’t adjust at higher speeds (stuck at 3 bars) and I’m unable to adjust the height when in motion above ~21 mph. Any tips here? Less concerned about lowering the car at this point and just want to get this back to OEM. Thanks!
|
|
|
|
Post by donpalme on May 5, 2023 12:31:47 GMT
Switch on ignition - Drive Select -AUTO Open engine hood Control unit 74 Chassis control Read out adjustment values Body height of front left wheel arch edge Body height of front right wheel arch edge Body height of rear left wheel arch edge Body height of rear right wheel house edge Basic setting Activate level control Approach reference level Adjustment Enter new values Body height of front left wheel arch edge (value old plus x) Body height, wheel housing edge, front right (value old plus x) Body height of rear left wheel housing edge (value old plus x) Body height of rear right wheel arch edge (value old plus x) Basic setting Switch to normal level control function Activate level control Clear fault memory Hi all, I followed these steps and it worked, thanks for sharing. However I needed to readjust some heights an faultfully did it in dynamic mode. Now I have an not deletable error "C1046F6 axle load definition not performed". How do I get rid of that or do I have to go to Audi service now? Regards, David |
|
robta
New Member
Posts: 2
|
Post by robta on Aug 15, 2024 9:37:05 GMT
Found the solution for that right now:
Achslastbestimmung
STG74 - Fahrwerk >
[Grundeinstellung-04] >
IDE09282 MAS00675-Normalniveau in enger Regeltoleranz anfahren
IDE09279 MAS00675-Kalibrierung der Niveauregelung für Achslastbestimmung
IDE09283 MAS00675-Umschaltung auf normale Niveauregelfunktion
IDE03751 MAS00675-Niveauregelung aktivieren
Nun den Fehlerspeicher löschen und die Zündung für 1 min ausschalten.
|
|
|
|
Post by walker923 on Sept 5, 2024 22:37:52 GMT
Confirmed... This works 100%. Lowered the car 12mm, just enough to close that wheel well gap.
|
|
