|
|
Post by daniglimk5 on Jan 7, 2017 3:48:20 GMT
Hi, I am about to pull the trigger and buy the obdeleven, but before I do, I need to check and make sure that the software is cable to run the DSG - Adaptation - Re-calibration similar to VCDS Ross Wiki
Thanks! |
|
|
|
Post by rbpittman61 on Jan 9, 2017 5:05:01 GMT
Yes, the DSG calibration is something the OBDEleven can do. Just did mine the other day after a DSG service.
|
|
|
|
Post by Beasto on Feb 9, 2017 0:40:35 GMT
How did you do that exactly?
|
|
|
|
Post by Akusho on Feb 14, 2017 7:24:00 GMT
Would very much like to know as well.
|
|
|
|
Post by robpittman61 on Feb 16, 2017 4:44:39 GMT
Just follow the directions here but apply the actions to the OBD Eleven
Prerequisites:
## Fluid Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019.
## Selector Lever in P
## Ignition ON
## Engine ON (Idling) for one minute or more
## Brake Pedal operated (hold for the whole procedure)
## Throttle Pedal not operated
NOTE: Be sure to perform the following steps in the sequence shown, followed by the defined test drive.
[Select]
[02 - Transmission]
[Basic Settings - 04]
Transmission Tolerances (Engaged Calibration)
Group 061
[Go!]
## When you go to Basic Settings 061 and click GO the screen may look like this: Basic Settings 061
## Wait until the numbers quit moving and the trans will quit making noises. Basic Settings switches to On when finished: Basic Settings 061
Wait until Basic Settings has switched to ON and all numbers have stopped moving. This may take one minute.
Transmission Tolerances (Synch. Point. Measurement)
Group 060
[Go!]
## When you go to Basic Settings 060 and click GO the screen may look like this: Basic Settings 060
## Wait until the numbers quit moving and the trans will quit making noises. Basic Settings switches to On when finished: Basic Settings 060
Wait until Basic Settings has switched to ON and all numbers have stopped moving.
|
|
|
|
Post by Matthew on Feb 16, 2017 20:57:38 GMT
^^^The above was from Ross-Tech, but the OBDeleven equivalent doesn't actually "wait" until the process completes, so you may have to attempt it 2 or 3 times for it to really complete successfully.
|
|
|
|
Post by robpittman61 on Feb 21, 2017 20:47:17 GMT
Thank you Matthew, I forgot to add that into the instructions.
|
|
|
|
Post by Shredman on May 27, 2017 15:29:54 GMT
What about clutch adaptation? Is that that part of the process? I see tech Ross includes clutch as part of the whole process
|
|
|
|
Post by Matthew on May 28, 2017 6:06:28 GMT
I'll try the clutch adaptation tomorrow on my MK5 Golf GTI and see if it works.
|
|
|
|
Post by Shredman on May 28, 2017 19:08:03 GMT
I tried it yesterday and was getting errors on 062 and not available on 067, 068, 065 and 063 Groups. My DSG software is above 0800. Any ideas why I failed clutch adaptation??
|
|
|
|
Post by Shredman on Jun 2, 2017 16:49:21 GMT
Any updates on this??
Thanks
|
|
|
|
Post by Matthew on Jun 2, 2017 20:45:48 GMT
My clutch adaptation "never completes" in OBDeleven, but completes just fine with VCDS. I suspect that the OBDeleven app does not "listen" for feedback from the module, but relies on a timed interval to assume that the process is completed.
|
|
|
|
Post by Shredman on Jun 2, 2017 22:18:07 GMT
Intersting. What year and model is your GTI?
|
|
|
|
Post by Matthew on Jun 7, 2017 3:22:36 GMT
Intersting. What year and model is your GTI? My GTI is a 2008 Autobahn package I have the Eurodyne Stage2 engine flash, and the Eurodyne Stage1 DSG flash I'm currently putting down 286whp and 332whp on nitrous oxide. No issues with the DSG so far since the torque is transferred through the clutch packs without any slipping |
|
|
|
Post by Westindies on Sept 6, 2017 15:55:02 GMT
Hello,
I'm having issues with this reset on a S tonic Q3, obd getting (13) error message and i can't make it run.
Any clue?
|
|
|
|
Post by Hansdampf on Sept 8, 2017 16:00:52 GMT
You're in the VW Golf V Section here ...
Some types of resetting work by disconnecting the batterie for a few hours. Reconnecting and engine start will produce some adapting processes.
|
|
imran
New Member
Posts: 5
|
Post by imran on Jul 13, 2019 19:02:06 GMT
Sir Please suggest me. How too do basic setting with obd eleven pro please give me the full details
|
|
imran
New Member
Posts: 5
|
Post by imran on Jul 13, 2019 19:03:19 GMT
Skoda superb dsg 7 mechatronics setting
|
|
|
|
Post by Matthew on Jul 14, 2019 18:57:31 GMT
|
|
ok
New Member
Posts: 1
|
Post by ok on Jul 5, 2022 21:44:05 GMT
I have a 2010 Audi TT when I perform this re-cal using OBDeleven. When it is done the drive would not engage.
|
|
|
|
Post by Matthew on Jul 19, 2022 22:08:50 GMT
Did you get a message saying "implausible gear disengagement"?
|
|
