|
|
Post by ninjageezer on Jan 1, 2017 21:06:28 GMT
has anyone got any coding info on changing the discover media startup logos like in this video ? link |
|
|
|
Post by dv52 (Australia) on Jan 2, 2017 9:47:57 GMT
has anyone got any coding info on changing the discover media startup logos like in this video ? ninjageezer: Sure, this tweak is easy - just follow the screen shots below, then reset the MIB unit as described under the pictures:  In-car Procedure: Reset the MIBWith the MIB turned-on, press and hold-down the ON/OFF button until the MIB turns-off and then turns-on again (at least 10 seconds) Don |
|
|
|
Post by ninjageezer on Jan 2, 2017 16:01:12 GMT
has anyone got any coding info on changing the discover media startup logos like in this video ? ninjageezer: Sure, this tweak is easy - just follow the screen shots below, then reset the MIB unit as described under the pictures: In-car Procedure: Reset the MIBWith the MIB turned-on, press and hold-down the ON/OFF button until the MIB turns-off and then turns-on again (at least 10 seconds) Don Brill will give it a go thank you. |
|
|
|
Post by Extremeclimb on Jan 24, 2017 9:59:29 GMT
How come I do not have the 5F module in OBD11? How to I get the 5F module? ninjageezer: Sure, this tweak is easy - just follow the screen shots below, then reset the MIB unit as described under the pictures: In-car Procedure: Reset the MIBWith the MIB turned-on, press and hold-down the ON/OFF button until the MIB turns-off and then turns-on again (at least 10 seconds) Don Brill will give it a go thank you. |
|
|
|
Post by dv52 (Australia) on Jan 24, 2017 21:51:59 GMT
^ ^^^^^ What type of mk7 do you drive and what control modules do you see on the main screen (first screen in my picture)?
Don
|
|
|
|
Post by Extremeclimb on Jan 24, 2017 23:29:23 GMT
Hi
i am driving MK7 1.4TSI 2013
i have all the module as show in your pic. But I do not have information control unit 1 (5F)
this there anyway I can add that in.
thanks
|
|
|
|
Post by dv52 (Australia) on Jan 25, 2017 0:09:00 GMT
^^^^^^ That's real strange because it means that the Gateway module (@ address hex19) hasn't been told that the car has a MIB unit installed -so when you scan the car, the Gateway doesn't check for a module @ address hex 5F. Not sure why this would happen ?? Anyhow - you want it fixed, so try this: - On the first screen-shot below (which was taken from my test-bench - hence not many modules), select the red-pencil on the bottom right side of the picture.
- You should then see the 2nd screen below which is a full list of all the possible modules and those marked (in the box) are those modules that the Gateway has been told are installed on your car
- Scroll-down until you find 5F and mark the box
- Select OK to accept the change
- Be careful when adding modules to the Gateway list - select only those modules that you are certain are installed and don't inadvertently delete existing modules -or errors will result !
Don
|
|
|
|
Post by Extremeclimb on Jan 25, 2017 0:28:53 GMT
Hi
i just checked, under the gateway list coding, 5F is selected. But after the scan, the 5F module disappear again.
|
|
|
|
Post by dv52 (Australia) on Jan 25, 2017 0:33:37 GMT
^^^^^ post-up your scan report-please
|
|
