Post by r3ealnd on Dec 25, 2020 2:17:52 GMT
HUGE PROBLEMS AFTER CODING PROBABLY DUE TO WRONG CODING
First of all, Merry Christmas to you all. I hope you are healthy and y'all stay safe.
ATTENTION LONG TEXT - SORRY
I recently got a Passat CC 3.6 4 Motion US version. Since today I also have OBDEleven in the Pro version with IOS.
Years ago I had something to do with VCDS but am not an expert. I started to code the basics with apps, everything
worked (seat belt warning deactivated, seat heating save setting for 10 minutes, air circulation memory after ignition off, windows open and close with remote control, turn signals as position lights)
I read out and deleted the error memory beforehand. Some mistakes were and are rightly there. Everything that has to do with
radio and navigation system, because I have installed a Kenwood CarPlay radio, electric parking brake short circuit to ground - I have to change the switch.
and finally driver's door window up. It goes down automatically but not up. In addition, tire pressure control. The seller bought
other rims and installed the sensors there. I didn't buy the rims and the factory rims without sensors. I ordered sensors from Ebay
that will come next week. So far so good, now I've coded something for which there are no apps
Door open warning signal - region changed from USA to Germany. Works, the warning tone is gone. No new mistakes
After filling up, my fuel gauge was only a little over 3/4 full. For this there is an adaptation in the Ios version different
from Android. Here the value does not go from 120 to 136 with standard 128 but from 0 to 10. Needle went up at 10 but not to completely full. Tried different values from 1-10 and left it at 10. No new mistakes.
The speed display in my CC is very imprecise. 4-6 miles slower than shown. With KMH still bearable, with miles not anymore. Asked by Google and found out in module 17, dash panel insert K change value. If 4 was set according to the instructions, a smaller value indicates more speed and a larger value indicates a lower speed. So K value changed from 4 to 2.
When I wanted to drive off a little later to check the setting - AIRBAG LIGHT ON Error in the display Airbag Service- ESP AND ABS LIGHT ON (ESP can no longer be switched on or off
Error memory read out with the following results:
- BRAKE
3 errors cannot be deleted
Code 01317 static Instrument Cluster Control Module
Code 01044 static Control Module incorrectly coded
Code 0078 static Steering Angle sensor no or incorrect basic Setting / adaptation
- AIR CONDITION
1 error cannot be cleared
Code B10A715 static indirect ventilation door motor potentiometer
- AIRBAG
1 error can be deleted but comes back
Code 03551 static Function Restriction of Seat occupied recognition
- DRIVER DOOR
1 error can be deleted (probably defective switch)
Code 00932 static Motor for Window lift driver site no or incorrect basic Setting / adaptation
- STEERING ASSISTANCE
1 error cannot be deleted
Code 00778 static Steering Angle Sensor no or incorrect basic Setting / adaptation
- HEADLIGHT REGULATION
1 error cannot be cleared
Code 02988 static Left- / Right Hand driving switch-over active
- TIRE PRESSURE
1 error cannot be deleted because no sensors are currently installed
Code 01521 intermittent Tire Pressure Sensor No Signal / communication
The most important thing now is of course to get rid of the airbag and ABS errors and, ideally, to code everything back to the original.
But how. Long Coding bit Hex bit and bite I haven't done yet and don't have the right values for them. Can someone help me? I'm grateful
for all tips. We only have a very incooperative VW dealer in the region when it comes to cars that not sold through him.
The demand only to read out the error memory $ 180 plus tax
I say thank you in advance
First of all, Merry Christmas to you all. I hope you are healthy and y'all stay safe.
ATTENTION LONG TEXT - SORRY
I recently got a Passat CC 3.6 4 Motion US version. Since today I also have OBDEleven in the Pro version with IOS.
Years ago I had something to do with VCDS but am not an expert. I started to code the basics with apps, everything
worked (seat belt warning deactivated, seat heating save setting for 10 minutes, air circulation memory after ignition off, windows open and close with remote control, turn signals as position lights)
I read out and deleted the error memory beforehand. Some mistakes were and are rightly there. Everything that has to do with
radio and navigation system, because I have installed a Kenwood CarPlay radio, electric parking brake short circuit to ground - I have to change the switch.
and finally driver's door window up. It goes down automatically but not up. In addition, tire pressure control. The seller bought
other rims and installed the sensors there. I didn't buy the rims and the factory rims without sensors. I ordered sensors from Ebay
that will come next week. So far so good, now I've coded something for which there are no apps
Door open warning signal - region changed from USA to Germany. Works, the warning tone is gone. No new mistakes
After filling up, my fuel gauge was only a little over 3/4 full. For this there is an adaptation in the Ios version different
from Android. Here the value does not go from 120 to 136 with standard 128 but from 0 to 10. Needle went up at 10 but not to completely full. Tried different values from 1-10 and left it at 10. No new mistakes.
The speed display in my CC is very imprecise. 4-6 miles slower than shown. With KMH still bearable, with miles not anymore. Asked by Google and found out in module 17, dash panel insert K change value. If 4 was set according to the instructions, a smaller value indicates more speed and a larger value indicates a lower speed. So K value changed from 4 to 2.
When I wanted to drive off a little later to check the setting - AIRBAG LIGHT ON Error in the display Airbag Service- ESP AND ABS LIGHT ON (ESP can no longer be switched on or off
Error memory read out with the following results:
- BRAKE
3 errors cannot be deleted
Code 01317 static Instrument Cluster Control Module
Code 01044 static Control Module incorrectly coded
Code 0078 static Steering Angle sensor no or incorrect basic Setting / adaptation
- AIR CONDITION
1 error cannot be cleared
Code B10A715 static indirect ventilation door motor potentiometer
- AIRBAG
1 error can be deleted but comes back
Code 03551 static Function Restriction of Seat occupied recognition
- DRIVER DOOR
1 error can be deleted (probably defective switch)
Code 00932 static Motor for Window lift driver site no or incorrect basic Setting / adaptation
- STEERING ASSISTANCE
1 error cannot be deleted
Code 00778 static Steering Angle Sensor no or incorrect basic Setting / adaptation
- HEADLIGHT REGULATION
1 error cannot be cleared
Code 02988 static Left- / Right Hand driving switch-over active
- TIRE PRESSURE
1 error cannot be deleted because no sensors are currently installed
Code 01521 intermittent Tire Pressure Sensor No Signal / communication
The most important thing now is of course to get rid of the airbag and ABS errors and, ideally, to code everything back to the original.
But how. Long Coding bit Hex bit and bite I haven't done yet and don't have the right values for them. Can someone help me? I'm grateful
for all tips. We only have a very incooperative VW dealer in the region when it comes to cars that not sold through him.
The demand only to read out the error memory $ 180 plus tax
I say thank you in advance