|
|
Post by blackpearl on Oct 18, 2020 12:03:50 GMT
![]() Did use the Scandinavian DRL app function after that the right inner tail light stays on until I lock the car, tried to reverse the app but did not matter the light still is on until the car gets locked 🙁 sometimes I leave it open on my yard at my house if I forget to lock it ofcourse finally will drain my battery - any ideas to get this turned off?  |
|
ViĆ
Full Member
Posts: 185
|
Post by ViĆ on Oct 18, 2020 16:18:34 GMT
Would you be so kind an share some more information.
if you go into
Central Electrics (09)
-Adaption
Then I would like you to take a screenshots of the values inside below submenus and share the screenshots here.
Leuchte16
Leuchte17
Leuchte23
Leuchte24
|
|
|
|
Post by blackpearl on Oct 25, 2020 11:19:46 GMT
|
|
ViĆ
Full Member
Posts: 185
|
Post by ViĆ on Oct 25, 2020 16:18:49 GMT
I think i found your problem.
Central Electrics (09)
-Adaption
--Leuchte16
---Lichtfunktion A 16
----Current value: Klemme30
----Change to: Standlicht algemein...
Press and hold green tick. it might ask for security code, enter 31347
Edited an hour after:
I got 2 questions for you
Do you have any errors/faults inside Central Electrics (09) ?
The reason I am asking this is because inside Leuchte16 -> "Fehlerort mittleres Byte DTC-DFCC 16:" is set to 0
Correct me if I am wrong. the only time I have seen it being set to 0 is when a Leuchte group is not in use which in your case it should be in use
Have you coded your outer taillights as indicators/blinkers?
The reason I am asking that is because i see the values "Blinken Links Hellphase" & "Blinken Rechts Hellphase" coded inside Leuchte23 and Leuchte24
Leuchte23 and Leuchte24 on my variant is the outer taillights
Either you have coded it yourself then just ignore it. if you havent coded it then one of the apps you used coded that then you might wanna change it back.
The "issue" wont be visible if you have scandinavian DRL enabled. Easiest way to check is with engine/igniton off and hazard lights on
|
|
|
|
Post by blackpearl on Oct 25, 2020 18:35:53 GMT
Thanks Vic
it was the klemme30 issue 👍🏻
The other issue I did not even know there was
The taillights blinks as they ofcourse should not 🙄
How do I set them to normal?
|
|
ViĆ
Full Member
Posts: 185
|
Post by ViĆ on Oct 25, 2020 18:57:00 GMT
Glad to hear it got sorted
What about my first question, do you have any error/faults on Central electrics?
To remove the taillight indicator/blinker
Central Electrics (09)
-Adaption
--Leuchte23
---Lichtfunktion A 23
----Current value: Blinken Links Hellphase
----Change to: Standlicht algemein...
_________________
--Leuchte24
---Lichtfunktion A 24
----Current value: Blinken Rechts Hellphase
----Change to: Standlicht algemein...
|
|
|
|
Post by blackpearl on Oct 25, 2020 21:34:25 GMT
Thanks again Vic now the blink is as it should too  and you are right about the fault code in central electrics as I really dont know where it goes to   |
|
ViĆ
Full Member
Posts: 185
|
Post by ViĆ on Oct 27, 2020 12:20:02 GMT
That fault has nothing to do with what i was thinking earlier. Could be from anything really.
Sorry cant help you further, maybe someone else can step in with any aditional knowledge about that error.
We got the most important issues solved. Which i am happy about.
|
|
|
|
Post by dv52 (Australia) on Oct 27, 2020 20:16:16 GMT
blackpearl : Try changing Leuchte17TFL R BLK SRB3TFL R BLK SR KC3-Fehlerort mittleres Byte DTC-DFCC 17 to 0Don
|
|
|
|
Post by blackpearl on Oct 29, 2020 14:46:52 GMT
Thats more than ok Don , Thank you so much 😊👍🏻
|
|
