|
Post by hannibalm on Jan 21, 2020 16:16:32 GMT
Good morning. A6 4G Facelift owners with Night Vision? I would need indications on coding
|
|
|
Post by hannibalm on Jan 13, 2021 18:38:47 GMT
Hello. Have you already installed all the correct components for the Facelift and installed the wiring?
First of all via the diagnosis interface - enter address 19 (Gateway) - Select the encryption / installation list - Activate and confirm address 84 (Night vision system) - Save and exit the control unit
- Enter address 84 (Night vision system) - Select encoding Now enter the appropriate coding depending on the model. - Example I have coded: 401100 (You can see the coding entries in the various bytes / bits) - Remove the component protection Requires Odis with online account or contact an AUDI / VW Service -Calibrate the infrared camera through basic adjustments (This requires the appropriate instrument Vas 6430/6 and VAS 6430/4) follow the instructions -Reset memory faults - Carry out the functional test and test the system with a test image Changes are set in Address 84 (Night Vision System) - Connect address 84 (Night vision system) - Select the final check diagnosis Select the test image -> select START. If a test image is now displayed in the speedometer, if your speedometer is capable of displaying, otherwise it must be replaced (Generally for Facelift with ACC system it must be replaced with a suitable one)
|
|
|
Post by jorgeth on Jan 17, 2021 10:12:05 GMT
Does anyone know the wiring diagram to nigh vision module to canbus module 19??
|
|
|
Post by hannibalm on Jan 17, 2021 16:06:51 GMT
Only the CAN-BUS line must be connected, the two twisted orange / brown + orange / gray cables to the collective CAN-BUS connector located in the driver's left footwell. Remove the CAN isolation connector (large gray connector) Unlock the pink latch to the right. Press the CAN isolation connector down and remove it. Activate the pink lock and remove the cover cap. Remove the additional pink safety lock and remove the connector housing. Insert both lines of the wiring in the following chambers: PIN 16 - CAN L PIN 16 - CAN H
|
|
pitty
New Member
Posts: 43
|
Post by pitty on Oct 17, 2023 23:11:58 GMT
Hello guys, I retrofitted the night vision into my A6 my21 but I'd like to know if I coded everything correctly. I coded the night vision into address 19, 17 and 5F. Do I need to code it into A5 or another ECU?
|
|
|
Post by hannibalm on Oct 18, 2023 17:02:57 GMT
I wouldn't know exactly about the Audi C8. For C7, control unit 84 (Night vision) must be enabled in 19, the menu must be activated in 5F and coded
|
|
pitty
New Member
Posts: 43
|
Post by pitty on Oct 20, 2023 11:05:15 GMT
This is the coding I've done so far:
19 Gateway > Select installation list > 84 (Night vision system) 84 Night vision system > Conding 07 > byte 0 > bit 0-3 country RdW byte 0 > bit 4-7 vehicle class AU581 (TOP) byte 1 > bit 0-3 with star&stop byte 1 > bit 4-7 LWR with two sensorLWR byte 2 > bit 0 with fas_profile byte 2 > bit 2 traffic_jam_assist installed 03-ABS Byte 9 > bit 1 - NOT SURE IF NEEDED AS IT'S NOT DESCRIBED 17-Instrument Byte 10 > bit 3 Nightvision yes Byte 13 > bit 4 Nightvision_BAP yes 82-Head up Display Byte 00 > bit 4 Nightvision system installed A5 Frt Sens. Drv. Assist Byte 16 > bit 6 FW_NV,installed 5F Multemedia > adaptations > Vehicle menu operation-menu display night vision activated 5F Multemedia > adaptations > Vehicle menu operation-menu display night vision over threshold high activated 5F Multemedia > adaptations > Vehicle function list BAP-night vision_0x18 activated 5F Multemedia > adaptations > Vehicle function list BAP-night vision_0x18 msg_bus Terminal 15
|
|