|
Post by abousnina on Sept 27, 2018 11:10:38 GMT
I purchased the following OPS package for my Golf 7, got installed. Now when I try to perform the coding Parking Assistance (Module 76) I get function not available. Any idea why ? Attached are the coding details I couldn't find module 10 the 76 showed up instead vw_golf_mk7-_pdc_ang_v10.pdf (745.3 KB)
|
|
|
Post by ofektal8 on Sept 27, 2018 12:13:45 GMT
I purchased the following OPS package for my Golf 7, got installed. Now when I try to perform the coding Parking Assistance (Module 76) I get function not available. Any idea why ? Attached are the coding details I couldn't find module 10 the 76 showed up instead View AttachmentHey, had this issue and got it fixed. Does this happen when you are trying to code the park assist module? And what is the current coding of the park assist module
|
|
|
Post by abousnina on Sept 27, 2018 12:24:16 GMT
Hey, had this issue and got it fixed.
Does this happen when you are trying to code the park assist module? And what is the current coding of the park assist module Yes it happens when i try apply the values i changed (all set to default before change) FYI the 76 shows in red (is that a problem) ? Thank you !
|
|
|
Post by ofektal8 on Sept 27, 2018 14:13:06 GMT
Yes it happens when i try apply the values i changed (all set to default before change) FYI the 76 shows in red (is that a problem) ? Thank you ! Yes thats what happend to me, can you please post a scan of the park assist module? When it is red it means there are faults, but after proper coding it should turn green.
|
|
|
Post by abousnina on Sept 27, 2018 14:26:38 GMT
I've noticed that there are several other errors so here is the full list
|
|
|
Post by ofektal8 on Sept 27, 2018 15:38:25 GMT
I've noticed that there are several other errors so here is the full list Ok, did you have those faults(not in the park assist module) before installing the ops kit? And what pins did you connect the module to in the gateway? One suggestion i have now is to first go to security access and enter the code it will give you and then try to code it.
|
|
|
Post by abousnina on Sept 27, 2018 17:37:30 GMT
I did not have any errors prior to that, as for the pins i followed the guide that i attached on the initial post
Connect orange wire (can high) to pin number 17 in CAN gateway. Connect brown wire (can low) to pin number 7 in CAN gateway.
|
|
|
Post by ofektal8 on Sept 27, 2018 17:53:01 GMT
I did not have any errors prior to that, as for the pins i followed the guide that i attached on the initial post Connect orange wire (can high) to pin number 17 in CAN gateway. Connect brown wire (can low) to pin number 7 in CAN gateway. Ok, And Here is the problem. OPS is connected to pins 8(LOW) and 18(High), you connected it to canbus extended and not to running gear sensors. im not sure if it can do any damage to the car but be on the safe side and switch them as fast as possible.
|
|
|
Post by abousnina on Sept 27, 2018 18:39:48 GMT
|
|
|
Post by ofektal8 on Sept 27, 2018 18:55:39 GMT
so if i understand you properly - the attached guide is not correct ? the attached guide says 8 and 18 look in the pictures
|
|
|
Post by abousnina on Sept 27, 2018 21:30:10 GMT
sorry it's in 8 and 18 as described i don't really know why i've said 7 and 17.
what do you advice next ?
|
|
|
Post by ofektal8 on Sept 27, 2018 22:23:52 GMT
sorry it's in 8 and 18 as described i don't really know why i've said 7 and 17. what do you advice next ? Have you tried this? "One suggestion i have now is to first go to security access and enter the code it will give you and then try to code it."
|
|
|
Post by caritaxd24 on Jan 4, 2019 15:25:06 GMT
Hi friends. I have the same problem. I followed all the instructions. Can bus are in 8/18. But module comes in 000000000 not let coding. Have same errors. When I tried to write the long code it doesn’t receive. 0031151011
|
|
|
Post by ofektal8 on Jan 4, 2019 16:36:42 GMT
Hi friends. I have the same problem. I followed all the instructions. Can bus are in 8/18. But module comes in 000000000 not let coding. Have same errors. When I tried to write the long code it doesn’t receive. 0031151011 After looking at His scan i now see His module is missing parameters and probably yours too. You need someone with access to Geniune VCP Or ODIS Online to upload those parameters
|
|
|
Post by caritaxd24 on Jan 16, 2019 3:36:13 GMT
Hi friends. I have the same problem. I followed all the instructions. Can bus are in 8/18. But module comes in 000000000 not let coding. Have same errors. When I tried to write the long code it doesn’t receive. 0031151011 After looking at His scan i now see His module is missing parameters and probably yours too. You need someone with access to Geniune VCP Or ODIS Online to upload those parameters No one of them works. I went to a dealer we tried with Odis even online solution and nothing. Previously I was proved with other module of an S3 and it works well. That’s mean that wires connections are well. Maybe the problem it’s just the module.
|
|
|
Post by ofektal8 on Jan 16, 2019 10:03:29 GMT
After looking at His scan i now see His module is missing parameters and probably yours too. You need someone with access to Geniune VCP Or ODIS Online to upload those parameters No one of them works. I went to a dealer we tried with Odis even online solution and nothing. Previously I was proved with other module of an S3 and it works well. That’s mean that wires connections are well. Maybe the problem it’s just the module. Thats what i said, the module is missing parameters, so you wont be able to code it ever with anything until you upload them. Your dealer doesnt know how to use ODIS Then, Try to find someone with Geniune VCP he can upload it in 2 mins, or find a better dealer xD
|
|
con
New Member
Posts: 1
|
Post by con on Sept 10, 2019 11:39:44 GMT
Hi Guys,
New to coding, but after reading a lot, I think, we can all nut this out together. 2018 golf mk7.5
Purchased a kit from aliexpress, same kit as carsys. installed and tried to code it and same thing error 31. the park assist comes up as control unit #76 not #10, this cannot be changed as #10 does not appear in the installation list of gateway #19. the long coding I was told to use is:- 003151011 after doing some searching I came across a forum with long code:-0451141811 I entered it and code was excepted.
I did all the other coding required. no errors in any control units.
I get all the graphics and the beep when I shift to reverse and big car graphic when shifting into drive.
but I get no moving sensor bars on the graphics of infotainment unit or audio beeping through the buzzers from park assist module as im reversing or driving toward an object.
I disconnected the front connector of the ops module and an error came up showing that front sensors not working.
OMG what is going on, has anybody got an idea, so close yet so far away :-) BTW VW MQB HIGH GATEWAY
|
|