|
Post by Martynas Šileika on Apr 13, 2018 6:24:10 GMT
Fixed TP1.6 connection issue Fixed Adaptation history after test value Improved KWP1281 and KWP2000 measurements
Need to test vehicle mileage if someone still get negative value.
Also fixed crash in 0.9.3.3 caused by 0.9.3.2 on Android 4.4 devices
|
|
zooks
New Member
Posts: 3
|
Post by zooks on Apr 13, 2018 10:52:17 GMT
updated to 0.9.3.2 and now crashes on trying access various control modules 'unfortunately obdeleven has stopped'
|
|
|
Post by Martynas Šileika on Apr 13, 2018 10:57:32 GMT
updated to 0.9.3.2 and now crashes on trying access various control modules 'unfortunately obdeleven has stopped' Hi, please update the app again. Your issue is fixed now!!!
|
|
zooks
New Member
Posts: 3
|
Post by zooks on Apr 13, 2018 11:11:31 GMT
ok thanks
|
|
matt
Closed beta tester
Posts: 48
|
Post by matt on Apr 13, 2018 12:46:33 GMT
Are MAF sensor negative live data values fixed?
|
|
|
Post by Martynas Šileika on Apr 13, 2018 13:05:39 GMT
Are MAF sensor negative live data values fixed? Could you test and report is values look like ok? We worked on measured values calculation formulas, but had not possibility to test every single measurement.
|
|
matt
Closed beta tester
Posts: 48
|
Post by matt on Apr 13, 2018 13:12:44 GMT
I will test and report back. The values were turning negative at a certain point so it should be an easy problem to find/fix
|
|
|
Post by zeal8080 on Apr 14, 2018 13:46:28 GMT
I updated 0.9.3.3. But I still could not sent cording history by e-mail. I did sent the history 0.9.2.x. orrectly.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Apr 14, 2018 14:33:36 GMT
works ok for me using android 7 on samsung s6 for a seat 2014 can you give dev your details if it still dont work after you do a app data clear
|
|
|
Post by Martynas Šileika on Apr 14, 2018 17:38:57 GMT
I updated 0.9.3.3. But I still could not sent cording history by e-mail. I did sent the history 0.9.2.x. orrectly. Could you provide detailed information what happens when you try to send history log?
|
|
|
Post by krystian660 on Apr 15, 2018 22:53:18 GMT
Fixed TP1.6 connection issue Issue fixed but still there is problem with endless "status" looping. forum.obdeleven.com/post/10771There is issue with status looping after basic setting in brakes (stg 03 - TP1.6) and headlight range (stg 55). Seat Ibiza 6J FR 2013 Even if basic setting is finished the status bar still indicates "running"
|
|
|
Post by Martynas Šileika on Apr 16, 2018 6:52:43 GMT
Fixed TP1.6 connection issue Issue fixed but still there is problem with endless "status" looping. forum.obdeleven.com/post/10771There is issue with status looping after basic setting in brakes (stg 03 - TP1.6) and headlight range (stg 55). Seat Ibiza 6J FR 2013 Even if basic setting is finished the status bar still indicates "running" As i can see in headlight control module (55), once you change channel the status changes to 'OFF'. This is normal behavior on some control units and the status don't change until you close and reopen basic settings channel. What happens to Brakes control unit (03) needs better investigation. Maybe there is an issue with closing basic settings channel, but also could be the specific control unit behavior. Please do the basic settings in Brakes again as in video with changing channels after complete basic and send a 'Report error'. As of your current report, i see that the status 'ON' is coming from control unit.
|
|
|
Post by tomtee on Apr 17, 2018 0:45:17 GMT
Hi,
I have been using OBD11 for months to display & clear faults for my 1993 VW. It worked great until yesterday. There was an update for version 0.9.3.3 pending for the OBD11 app in the Play store. After updating it I connected to the software for a scan. After the scan a known fault in the Engine module is no longer being displayed. Also the ABS scan now takes about 5 seconds where in the past it used to take several minutes. Furthermore when testing the ABS system the app shows an error during when it loads data. The message is "Control unit not responding". The ABS light on the dash does blink on-off during the attempt to scan that module.
The OBD device connects to my tablet as transmits data since the lights (red, amber, and green) all blink.
To try and fix it, I tried to clear the cache & data, log in then log out, and also uninstall & re-install the OBDEleven software on my tablet. None of these attempts to fix it has worked. So right now it's a useless device. Can someone from development take a look into it. Let me know if more info is needed.
Thanks, Tom
|
|
|
Post by OBDeleven on Apr 17, 2018 7:42:45 GMT
Hi, I have been using OBD11 for months to display & clear faults for my 1993 VW. It worked great until yesterday. There was an update for version 0.9.3.3 pending for the OBD11 app in the Play store. After updating it I connected to the software for a scan. After the scan a known fault in the Engine module is no longer being displayed. Also the ABS scan now takes about 5 seconds where in the past it used to take several minutes. Furthermore when testing the ABS system the app shows an error during when it loads data. The message is "Control unit not responding". The ABS light on the dash does blink on-off during the attempt to scan that module. The OBD device connects to my tablet as transmits data since the lights (red, amber, and green) all blink. To try and fix it, I tried to clear the cache & data, log in then log out, and also uninstall & re-install the OBDEleven software on my tablet. None of these attempts to fix it has worked. So right now it's a useless device. Can someone from development take a look into it. Let me know if more info is needed. Thanks, Tom I have activated report error function for your account, please connect to your Engine control unit > go to Faults > press three dots in top right corner and report error, do same after you try to connect to ABS control unit.
|
|
|
Post by tomtee on Apr 17, 2018 13:25:25 GMT
Hi, I have been using OBD11 for months to display & clear faults for my 1993 VW. It worked great until yesterday. There was an update for version 0.9.3.3 pending for the OBD11 app in the Play store. After updating it I connected to the software for a scan. After the scan a known fault in the Engine module is no longer being displayed. Also the ABS scan now takes about 5 seconds where in the past it used to take several minutes. Furthermore when testing the ABS system the app shows an error during when it loads data. The message is "Control unit not responding". The ABS light on the dash does blink on-off during the attempt to scan that module. The OBD device connects to my tablet as transmits data since the lights (red, amber, and green) all blink. To try and fix it, I tried to clear the cache & data, log in then log out, and also uninstall & re-install the OBDEleven software on my tablet. None of these attempts to fix it has worked. So right now it's a useless device. Can someone from development take a look into it. Let me know if more info is needed. Thanks, Tom I have activated report error function for your account, please connect to your Engine control unit > go to Faults > press three dots in top right corner and report error, do same after you try to connect to ABS control unit. I created three error reports for you. These were titled as Engine, ABS, and Main. FYI the OBD app would not let me scan the ABS module since it cannot connect to the ABS controller so I created that report from the main menu. If you need more info from me let me know. Thank you for your fast response. If it matters I am running Android v4.2.2 Tom
|
|
|
Post by nnquynh on Apr 18, 2018 7:07:26 GMT
My OBD11 was working fine. But after newest OBD software update last month it could not read some control units (5F Information Control Unit, 62 Door Electronics Rear Left and 72 Door Electronics Rear Right). I have closed and unlocked all doors properly. Does anybody know how to fix this?
|
|
|
Post by zeal8080 on Apr 18, 2018 11:10:47 GMT
When I touched "Mail" Icon on Hirtory menu, "Generatiing log..." Icon was poped up but nothing happen. I already set my e-mail address on setting menu. I an using Huawei Media Pad M3 with Android 7.0 and EMUI 5.0.1.
|
|
matt
Closed beta tester
Posts: 48
|
Post by matt on Apr 18, 2018 12:34:03 GMT
MAF values appear to be correct however graphing data freezes and stops working until it is reset and then re freezes after a short time etc
|
|
|
Post by Martynas Šileika on Apr 18, 2018 13:15:23 GMT
MAF values appear to be correct however graphing data freezes and stops working until it is reset and then re freezes after a short time etc Could you provide a video of your problem? I dont clearly understand what is wrong?
|
|
|
Post by Martynas Šileika on Apr 18, 2018 13:20:18 GMT
I created three error reports for you. These were titled as Engine, ABS, and Main. FYI the OBD app would not let me scan the ABS module since it cannot connect to the ABS controller so I created that report from the main menu. If you need more info from me let me know. Thank you for your fast response. If it matters I am running Android v4.2.2 Tom Thank you, we have found your logs. Trying to investigate your issues.
|
|
|
Post by Martynas Šileika on Apr 18, 2018 13:27:56 GMT
My OBD11 was working fine. But after newest OBD software update last month it could not read some control units (5F Information Control Unit, 62 Door Electronics Rear Left and 72 Door Electronics Rear Right). I have closed and unlocked all doors properly. Does anybody know how to fix this? Hello, could you confirm that these control units were be accessed with previous version? Because we dont see that you have been accessed them any time before update.
|
|
|
Post by nnquynh on Apr 19, 2018 1:16:01 GMT
Oh, I am sory. I have checked and see that before it did not try to read these control units, but after update it try to read these units and could not (I do not change anything in setting).
|
|
|
Post by Martynas Šileika on Apr 19, 2018 7:14:00 GMT
Oh, I am sory. I have checked and see that before it did not try to read these control units, but after update it try to read these units and could not (I do not change anything in setting). So in your vehicle control units 62 and 72 are listed in the gateway list, but they cant be connected. this is your vehicle's behavior. About 5F control unit, what exact unit is fitted to your car? Any photo? Does it come pre-installed to your vehicle or is retrofitted.
|
|
|
Post by nnquynh on Apr 19, 2018 16:40:53 GMT
So in your vehicle control units 62 and 72 are listed in the gateway list, but they cant be connected. this is your vehicle's behavior. About 5F control unit, what exact unit is fitted to your car? Any photo? Does it come pre-installed to your vehicle or is retrofitted. I retrofit an android headunit (S160 from China)
|
|
|
Post by Martynas Šileika on Apr 19, 2018 17:33:55 GMT
I retrofit an android headunit (S160 from China) So maybe this head unit don't work the same way as original VW head units, or maybe it doesn't have diagnostic functionality at all. Have you tried to connect to it with other diagnostic tools?
|
|
|
Post by krystian660 on Apr 19, 2018 21:48:32 GMT
2.0 TDI BMR Live data Channel 68 Value 2 In most Internet opinion value 2 should be soot mass in DPF. We have got strange value.
|
|
|
Post by tomtee on Apr 20, 2018 13:25:33 GMT
I created three error reports for you. These were titled as Engine, ABS, and Main. FYI the OBD app would not let me scan the ABS module since it cannot connect to the ABS controller so I created that report from the main menu. If you need more info from me let me know. Thank you for your fast response. If it matters I am running Android v4.2.2 Tom Thank you, we have found your logs. Trying to investigate your issues. Hi Martynas, I know you are very busy but wanted to ask if you had a chance to look at the error logs I produced for you & if you have a way to fix the OBD11 problems? Regards, Tom
|
|
|
Post by Martynas Šileika on Apr 20, 2018 17:12:00 GMT
Hi Martynas, I know you are very busy but wanted to ask if you had a chance to look at the error logs I produced for you & if you have a way to fix the OBD11 problems? Regards, Tom Currently we found the same abs control module to test with, so i hope next week we find and fix this issue. With engine control module i see that when trying to read faults, software gets negative response from control module. This looks very strange. When was the last time you have connected to your car when you saw a fault? Have you done any changes to your vehicle? Maybe you have possibility to try with other diagnostic tool?
|
|
|
Post by tomtee on Apr 20, 2018 18:58:50 GMT
Hi Martynas, I know you are very busy but wanted to ask if you had a chance to look at the error logs I produced for you & if you have a way to fix the OBD11 problems? Regards, Tom Currently we found the same abs control module to test with, so i hope next week we find and fix this issue. With engine control module i see that when trying to read faults, software gets negative response from control module. This looks very strange. When was the last time you have connected to your car when you saw a fault? Have you done any changes to your vehicle? Maybe you have possibility to try with other diagnostic tool? The last time I connected was probably just a few weeks ago. I was using it regularly to diagnose a fault in the SAI system. No changes were done to my vehicle. The only recent change was the OBD11 app upgrade. I do not have another diagnostic tool on hand. My only options are pulling the VAG blink codes (which is how I displayed faults before buying OBD11) or bringing the car to a shop. It was mentioned in another thread about rolling back to another level/version of OBD11. This would be preferable to waiting for fixes as a short term measure. How difficult would it be for someone on your team to post a link here for downloading the executable software like in the Play store along with instructions on how to install it?
|
|
dazz
New Member
Posts: 12
|
Post by dazz on Apr 22, 2018 3:21:31 GMT
Hi, I am getting the same issue. OBDEleven Application prompts to Update. When you update the app, you try to hit "Connect", and screen tells you to update application. App doesn't connect to dongle.
Any help would be great.
Thanks
|
|