Post by Sam.r on Nov 12, 2024 22:46:55 GMT
Hello,
There is a post about different hacks for SQ7s one of them was to attempt to enable RS light animation but I made a stupid mistake and did not fully read that it is not supported. Long story short I reverted all the changes. However when I run a scan I keep getting faulty error U101400 Control module incorrectly coded under module 17-dashboard (Which I have not touched and there is on history of any changes)
The only issue I noticed is that the VC takes much longer to turn off after shutting off the car. I used to see the 4 Audi ring screen then it would go dark now the 4 rings comes up then it switch to the rev gage screen then about 10sec later it goes dark
Error code:
OBDeleven vehicle history log
Date: 2024-11-12 17:28:32
VIN: xxxxxxxxxxxx
Car: Audi SQ7
Year: 2021
Body type: UNKNOWN
Engine: DCUE kW ( hp) l
Mileage: 57371 km
---------------------------------------------------------------
17 Dashboard
System description: FBenUSA------
Software number: 4K0920890D
Software version: 0022
Hardware number: 4K0920890D
Hardware version: H24
Faults:
U101400 - Control module incorrectly coded
static
Priority - 5
Malfunction frequency counter - 1
Unlearning counter - 168
km-Mileage - 57380 km
date - 2024-11-12 00:22:21
I have compared the current module configs with one from back up they both match. The only difference I have found was that under Adaptation Control module switch-off, counter=43 The backup was equal to 42. Made the change but didn’t clear the error
I have been searching everywhere but don’t seem to find a fix please help!
Here are other changes I made earlier that day:
- Activated Maneuver assist, via long code
- Easy Entry, via pre-built app
- soundaktor via pre-built app
- Automatic PDC activation, via pre-built app
- Acceleration display, enabled via the pre-built app (The I disabled it via the long code because that was the only dashboard related change I made. Did not clear the error)
please let me know if any you need anything else
There is a post about different hacks for SQ7s one of them was to attempt to enable RS light animation but I made a stupid mistake and did not fully read that it is not supported. Long story short I reverted all the changes. However when I run a scan I keep getting faulty error U101400 Control module incorrectly coded under module 17-dashboard (Which I have not touched and there is on history of any changes)
The only issue I noticed is that the VC takes much longer to turn off after shutting off the car. I used to see the 4 Audi ring screen then it would go dark now the 4 rings comes up then it switch to the rev gage screen then about 10sec later it goes dark
Error code:
OBDeleven vehicle history log
Date: 2024-11-12 17:28:32
VIN: xxxxxxxxxxxx
Car: Audi SQ7
Year: 2021
Body type: UNKNOWN
Engine: DCUE kW ( hp) l
Mileage: 57371 km
---------------------------------------------------------------
17 Dashboard
System description: FBenUSA------
Software number: 4K0920890D
Software version: 0022
Hardware number: 4K0920890D
Hardware version: H24
Faults:
U101400 - Control module incorrectly coded
static
Priority - 5
Malfunction frequency counter - 1
Unlearning counter - 168
km-Mileage - 57380 km
date - 2024-11-12 00:22:21
I have compared the current module configs with one from back up they both match. The only difference I have found was that under Adaptation Control module switch-off, counter=43 The backup was equal to 42. Made the change but didn’t clear the error
I have been searching everywhere but don’t seem to find a fix please help!
Here are other changes I made earlier that day:
- Activated Maneuver assist, via long code
- Easy Entry, via pre-built app
- soundaktor via pre-built app
- Automatic PDC activation, via pre-built app
- Acceleration display, enabled via the pre-built app (The I disabled it via the long code because that was the only dashboard related change I made. Did not clear the error)
please let me know if any you need anything else