Post by vwrobot on May 30, 2018 10:53:19 GMT
Hi All,
First post on these forums, unfortunately one for help. I am using the OBDeleven currently only for running diagnostics on a car I just bought. Had a problem today when adding some gateways to the car so I could run diagnostics that were not on by default (i.e to check faults on the KESSY etc) it completely made things go a little haywire temporarily and faults were everywhere (too many to list) up the car. After setting/resetting and removing the coded gateways back to the default list one by one the main residual fault is the deactivation of the ABS due to the module being incorrectly coded. I did not even touch the coding. Original coding was 0008214 which showed as a fault, then I set it to 0000000 to reset. Fault info below. Any idea on what the correct ABS code is? (or is the original 0008124 correct and I just need to set it back from 000000 again? To note the car has a missing front parking sensor that's been dislodged on delivery, could that have caused the ABS to deactivate (the ACC was putting up and error for a few runs). Note I added the All Wheel drive module by mistake in the first tun (the car has no AWD), I removed that gateway coding, but the fault remains.
**************************
03 Brakes
System description: J104 C2 450M VDCB
Software number: 3AA614109BM
Software version: 0040
Hardware number: 3AA614109BM
Hardware version: K03
Serial number: 00000008261047
Coding: 0008124
Trouble codes:
01044 - Control module incorrectly coded
static
Priority: 2
Frequency counter: 1
Driving cycle: 203
01324 - All wheel drive control module
static
************************
03 Brakes
System description: J104 C2 450M VDCB
Software number: 3AA614109BM
Software version: 0040
Hardware number: 3AA614109BM
Hardware version: K03
Serial number: 00000008261047
Coding: 0000000
Trouble codes:
01044 - Control module incorrectly coded
static
First post on these forums, unfortunately one for help. I am using the OBDeleven currently only for running diagnostics on a car I just bought. Had a problem today when adding some gateways to the car so I could run diagnostics that were not on by default (i.e to check faults on the KESSY etc) it completely made things go a little haywire temporarily and faults were everywhere (too many to list) up the car. After setting/resetting and removing the coded gateways back to the default list one by one the main residual fault is the deactivation of the ABS due to the module being incorrectly coded. I did not even touch the coding. Original coding was 0008214 which showed as a fault, then I set it to 0000000 to reset. Fault info below. Any idea on what the correct ABS code is? (or is the original 0008124 correct and I just need to set it back from 000000 again? To note the car has a missing front parking sensor that's been dislodged on delivery, could that have caused the ABS to deactivate (the ACC was putting up and error for a few runs). Note I added the All Wheel drive module by mistake in the first tun (the car has no AWD), I removed that gateway coding, but the fault remains.
**************************
03 Brakes
System description: J104 C2 450M VDCB
Software number: 3AA614109BM
Software version: 0040
Hardware number: 3AA614109BM
Hardware version: K03
Serial number: 00000008261047
Coding: 0008124
Trouble codes:
01044 - Control module incorrectly coded
static
Priority: 2
Frequency counter: 1
Driving cycle: 203
01324 - All wheel drive control module
static
************************
03 Brakes
System description: J104 C2 450M VDCB
Software number: 3AA614109BM
Software version: 0040
Hardware number: 3AA614109BM
Hardware version: K03
Serial number: 00000008261047
Coding: 0000000
Trouble codes:
01044 - Control module incorrectly coded
static