I own a 2003 Audi A4 1.8t Quattro and my ABS Control Module died. After buying another and putting it in I now need to code it.
Here are the steps I take for trying to code it.
Plug in the OBDEleven bluetooth connector. Connect the app. Open the module selection menu. Open the breaks menu. Open the coding menu. Apply the new code which is 5 numbers and something along the lines of 04752 I can't remember the exact numbers. It says there's an error.
I've also tried the same process but with the added step of opening the security tab and logging in. It then says the login is accepted and I try to code again. I then try to code again and it says the code is accepted however the code remains 00000 and does not change. When I open the change history logs it shows that the code was changed and it displays the old code and new code. 00000 Changed to 04752 But the code does not change.
I cannot get the code to change and I'm not sure what the issue is. Are there additional steps I need to take before coding the ABS Module?
I've tried to find how to code it online but found little information specific to what I'm trying to do. However, while searching someone mentioned I needed to program my wheel angle sensor before the ABS Module, but this was just a comment on the forum post I found.
Any help on this issue would be amazing, if any additional information is needed let me know and I will post it.
Here is a nice guide that hopefully helps you out, if you have seen this before, look at the "Notes" it gives special login codes for certain vehicles. I have been struggling getting even just my initial log in code to take. I just now finally noticed that their "notes" call for a different code than i get following theq guide,only by 1 digit. i have not tried this yet, but could explain my issues. Just my $0.02 hope it helps.
Last Edit: Aug 29, 2017 19:32:14 GMT by hazzard017
Murrumbidgee: @seb221 its available on ios but has limited functionality
Sept 11, 2019 7:15:57 GMT
Audirey: Couldnt seem to find it, but has anyone adjust DRL led intensity on a Audi S5 B8?
Sept 11, 2019 16:03:15 GMT
RogerMoore: Guys have an A7 is the A5 camera module the same as 85 front camera that I have?
Sept 12, 2019 15:42:15 GMT
RogerMoore: Sorry 85 onboard camera? It's installed on the top of the windscreen gaging out
Sept 12, 2019 15:42:43 GMT
Sept 12, 2019 15:42:52 GMT
ViĆ: Quick question before I go and purchase a new door module for my Golf MK7.5, I have a "5Q4959393F" Driver side door module and want to upgrade to one that ends with 592. Is there a difference between the last letter, can I mix 592F with 593B or E ?
Sept 12, 2019 16:02:56 GMT
ViĆ: or does driver module and passenger module need had to have same last letter ?
Sept 12, 2019 16:03:17 GMT
Cupra ~r: Anyone know how to change km to the actual car I changed quadrant and wanted to put the actual km.
Sept 13, 2019 14:35:05 GMT
Cupra R: Anyone know how to change km to the actual car I changed quadrant and wanted to put the actual km.
Sept 13, 2019 14:35:32 GMT
Ward: Anyone knows how u dan clearing defect drive assist button not working ?
Sept 13, 2019 14:57:38 GMT
billbobaggins1: Does anyone know if there are any changes that can be made to Audi A1?
Sept 14, 2019 12:09:30 GMT
Audirey: Cupra, what do you mean by changing km to the actual car? like just the units?
Sept 16, 2019 15:34:24 GMT
testeronline: If you mean can you change the millage shown on the car then No.
Sept 16, 2019 18:10:47 GMT
marcos: Dears: I made some chancges in the settings of the rear lights of my golf GTI 2013/14 and despite several attempts I could not make them work properly. Would you able to send me the settings original rear lights, the break ligth ond the brake lights so
Sept 17, 2019 18:40:41 GMT
theoldboy: Marcos if you check you history it will show you all the changes you have made, just reverse them. Or if you did a backup have a look at that.
Sept 17, 2019 20:31:17 GMT
marcos: Obrigado pela ajuda. Ocorre que verifiquei no histórico que utilizei o app para o modelo 7.5 do Golf. Ocorre que o meu é MK7. Já tentei de tudo e não consigo alterar. Será que alguém poderia me fornecer as configurações originais das luzes de direção?
Sept 17, 2019 22:17:28 GMT
Berry: I use the app download VIDEO in motion for RMC, after that all monitor change to German language, I go to change language, but I can't change any language the monitor just show., any solution PLEASE.
Sept 18, 2019 14:28:50 GMT