|
Post by zebster on Dec 13, 2016 12:42:53 GMT
Hi! I've been trying to enable mirror dip but i can't find "control access 2" under the Adaptarion menu in the Module 09 - Electronic. Any other way?
There's no app also...
I followed this guide:
|
|
|
Post by zebster on Dec 16, 2016 15:29:19 GMT
figured it out, had to search for "spiegel" under the adaptations menu and then i found the "Menuesteuerung Spiegelabsenkung" and "Spiegelabsenkung bei Rueckwaertsfahrt"
|
|
|
Post by wiz2003 on Dec 20, 2016 22:28:02 GMT
figured it out, had to search for "spiegel" under the adaptations menu and then i found the "Menuesteuerung Spiegelabsenkung" and "Spiegelabsenkung bei Rueckwaertsfahrt" Looks good - I want this for my RHD, so do you know what the sequence is for Left Mirror please?
|
|
Tell
New Member
Posts: 13
|
Post by Tell on Jan 12, 2017 17:26:58 GMT
figured it out, had to search for "spiegel" under the adaptations menu and then i found the "Menuesteuerung Spiegelabsenkung" and "Spiegelabsenkung bei Rueckwaertsfahrt" The all important menu option on Adaptations is "Spiegelverstellung"... then all is good. Thanks Zebster.
|
|
Tell
New Member
Posts: 13
|
Post by Tell on Jan 12, 2017 17:35:08 GMT
Wiz2003.
Yes the switch goes to L for a RHD, R for LHD.
Once I found the menu option under "Spiegelverstellung" I then found the two menus. I've documented on the English Ateca board. I can't say the drop of the mirror adds that much visibility but it does drop and goes back up again:). Thank Zebster for pioneering it for the Ateca.
|
|
|
Post by zebster on Jan 29, 2017 23:10:36 GMT
You're welcome
|
|
|
Post by xavier on Feb 10, 2017 10:32:26 GMT
My codification:
Module 09 ---> Spiegelverstellung -------->Funk Spiegelanklappung Modus, set "by look command via remote control key" -------->Spiegelanklappen, set "active" -------->Menusteuerung Funk Spiegel anklappen, set "active" Confirm, code 31347
|
|
|
Post by Jannesm on Mar 20, 2017 11:01:18 GMT
Hi!
Can the mirrors be coded so that only by ignition on/off they'll be extending? At the moment the mirrors open close by locking/unlocking the car... Thanks!
|
|
|
Post by wiz2003 on Apr 2, 2017 8:46:26 GMT
Wiz2003. Yes the switch goes to L for a RHD, R for LHD. Once I found the menu option under "Spiegelverstellung" I then found the two menus. I've documented on the English Ateca board. I can't say the drop of the mirror adds that much visibility but it does drop and goes back up again:). Thank Zebster for pioneering it for the Ateca. Thank you very much... Will look at doing this today...
|
|
totte
New Member
Posts: 7
|
Post by totte on Nov 27, 2018 10:44:36 GMT
Wiz2003. Yes the switch goes to L for a RHD, R for LHD. Once I found the menu option under "Spiegelverstellung" I then found the two menus. I've documented on the English Ateca board. I can't say the drop of the mirror adds that much visibility but it does drop and goes back up again:). Thank Zebster for pioneering it for the Ateca. Thank you very much... Will look at doing this today...
|
|
totte
New Member
Posts: 7
|
Post by totte on Nov 27, 2018 10:52:28 GMT
Hi ! I am new forum user. I have an Ateca MY18 and the Dip mirror function does not work. Does anyone have a solution for who does not have the pro version. Excuse English, I'm French
|
|
|
Post by Thirsty on Nov 27, 2018 11:27:57 GMT
Hi ! I am new forum user. I have an Ateca MY18 and the Dip mirror function does not work. Does anyone have a solution for who does not have the pro version. Excuse English, I'm French You need the pro version in order to use the features like coding, long coding and adaptation. These are needed in order to achieve such things. If the one click apps don't work you have two options: 1) Wait until they work / get fixed 2) Buy PRO (it's really worth it)
|
|
totte
New Member
Posts: 7
|
Post by totte on Nov 27, 2018 17:14:28 GMT
Thanks for the answer, I bought this device only for this application. How to know when the function will be modified ? Regards
|
|
|
Post by Thirsty on Nov 27, 2018 17:39:11 GMT
Thanks for the answer, I bought this device only for this application. How to know when the function will be modified ? Regards No problem That's hard to say when it'll get fixed. I think the app itself should work but there are problems with the newer car models (2018). I heard of users complaining that the VIM app isn't working on 2018 cars that's why i think this is caused by newer models. However you can request one click apps here: forum.obdeleven.com/board/379/click-apps-requests (use the format given in the first post) That's the best way in my eyes. I'm sorry that i can't do more for you atm.
|
|
|
Post by streetrod60 on Jul 15, 2019 5:59:10 GMT
Passcode 31347 is not worked for me. Any toughts?
|
|
|
Post by carbonchaos on Feb 9, 2020 23:19:08 GMT
Wiz2003. Yes the switch goes to L for a RHD, R for LHD. Once I found the menu option under "Spiegelverstellung" I then found the two menus. I've documented on the English Ateca board. I can't say the drop of the mirror adds that much visibility but it does drop and goes back up again:). Thank Zebster for pioneering it for the Ateca. You know you can adjust the mirror whilst it’s in it’s dipped position to a view of your liking for reversing, and it will return to this position every time it’s activated. then it will return to its normal driving position when you drive off again .
|
|
ggmu
New Member
Posts: 2
|
Post by ggmu on Mar 5, 2021 11:40:35 GMT
I am trying to active the mirror dip function for my Audi A1 2016, however can't seem to find Control Access 2, Menuesteuerung Spiegelabsenkung and Spiegelabsenkung bei Rueckwaertsfahrt under the drop-down menu when when selection Adaptation when in Module 09. Is it possible to search for the above if not listed int he drop-down menu?
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Mar 5, 2021 14:57:29 GMT
ggmu i am afraid the instructions come from the MQB Platform and I dont think your A1 is the same.
|
|
|
Post by tcmoila on Mar 16, 2021 13:47:30 GMT
Hi! I've been trying to enable mirror dip but i can't find "control access 2" under the Adaptarion menu in the Module 09 - Electronic. Any other way? There's no app also... I followed this guide: Hey there, is it possible to provide an update with the proper version of this?
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Mar 16, 2021 14:27:20 GMT
Try this - Its from the Leon thread but your previous coding was also from the Leon thread.
* Applicable from MY17 * 1 - Module 52 - Passenger door electronics 2 - Extended coding (Bytes Mode) 3 - Byte 04 - (Activate Bits 2 and 3) 4 - Module 09 - Electronic control unit - Code (31347) 5 - Adaptation 6 - Spiegelverstellung 7 - Menuesteuerung Spiegelabsenkung - (Change value to On) 8 - Spiegelabsenkung bei Rueckwaertsfahrt - (Change value to On)
To memorize the reverse gear position, set the mirror selector to R. Engage reverse. Adjust to a position that suits you. Put the gear out of reverse and wait a few seconds. Change the selector to 0 and the mirror should return to the normal driving position.
If you want it as a one clieck app then you have to request on it on the one click app thread.
|
|
|
Post by tcmoila on Mar 16, 2021 17:11:01 GMT
Thank you, car is a MY19 S3, I did it as instructed and still nothing, even tried redoing the App method, only mod I can’t get right for some odd reason I have also created an app request as per the instructions and advise above, hopefully they add it *crossing fingers*
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Mar 16, 2021 20:38:18 GMT
Two things.
If you don't mind can you post up a backup of control unit 52 and 09 (if you prefer just PM it to me)
Secondly the mirror button(on a right hand car) has to be set in the passenger side otherwise it dont work.
|
|
|
Post by josephkalel on Dec 31, 2021 15:47:52 GMT
Hello.. talking about the mirror I have cupra ateca 2020 and I activated the auto close function when close the doors but there’s no mirror folding feature and before the activation of the auto close they do it when I close via kessy ... so .. anyone knows how to activate or change the values for the folding when auto close ?
|
|
|
Post by josephkalel on Dec 31, 2021 15:48:44 GMT
I have a FULL BACK UP of all modules of my cupra ateca 20202 works for ya? Or which ateca is yours ?
|
|
|
Post by pedjasmek on Aug 28, 2023 16:57:39 GMT
I've enable mirror dip for my Skoda Octavia but I would like the mirror to fold even more then I first set it up. Can you tell me how to so that? Thank you
|
|
|
Post by ultraaslan88 on Jan 19, 2024 19:43:37 GMT
hi guys,i have an ateca excellence from end 2019. im new to coding/odb stuff. today i got my odb11 adapter. i tried the mirror dip function (one main reason, why i bought odb11), but it didn´t work. so, i have a few questions: 1. in one click apps, only things i can really change, should appear in the list? so, there won´t be any functionalities that i can´t change right? 2. the one click app for mirror dipping didn´t work. so, is there any other way to code it manually? if so, do you have a link for me?
|
|
OwnerTR
Junior Member
Seat Ateca FR
Posts: 84
|
Post by OwnerTR on Jan 21, 2024 9:34:21 GMT
The mirror will not work without a memory module. Enter offline OBD. 52 In the module "Live data" tab, does "mirror memory" look like the one in the picture? If not it won't work.
|
|
kiz77
New Member
Posts: 2
|
Post by kiz77 on Feb 17, 2024 11:13:31 GMT
i take it this is for the PFL Cupra Ateca too (2018), if so could you send me instructions please
|
|